Secura 6922671

Download PDF
Contents

SECURA Blade Holder Instruction Manual

Model: 6922671

Introduction

This manual provides essential information for the safe and correct installation, operation, and maintenance of your SECURA Blade Holder, model 6922671. This blade holder is designed for compatibility with MacAllister MPRM 53SP and B&S 675EXi R.S. lawn mowers. Please read these instructions thoroughly before installation and retain this manual for future reference.

Safety Information

Always prioritize safety when working with lawn mower components. Failure to follow these safety guidelines may result in injury or damage to equipment.

  • Disconnect Spark Plug: Before performing any maintenance or installation, always disconnect the spark plug wire to prevent accidental engine start-up.
  • Wear Protective Gear: Use appropriate personal protective equipment, including gloves and eye protection.
  • Stable Work Area: Ensure the lawn mower is on a flat, stable surface and cannot roll or tip over.
  • Proper Tools: Use only the correct tools for the job to avoid damaging components.
  • Genuine Parts: Use only genuine or approved replacement parts to ensure compatibility and safety.
  • Consult Professional: If you are unsure about any step, consult a qualified technician.

Product Overview

The SECURA Blade Holder (also known as a blade hub) is a critical component that connects the lawn mower blade to the engine's crankshaft. It ensures the blade rotates correctly and securely. This specific model is designed for MacAllister MPRM 53SP and B&S 675EXi R.S. lawn mowers.

SECURA Blade Holder, side view

Image 1: Side view of the SECURA Blade Holder, showing its overall structure and the central bore.

SECURA Blade Holder, top view

Image 2: Top view of the SECURA Blade Holder, highlighting the engine shaft bore and blade mounting points.

Installation Instructions

Follow these steps carefully to install the blade holder:

  1. Prepare the Mower: Ensure the lawn mower engine is off and cool. Disconnect the spark plug wire to prevent accidental starting.
  2. Access the Underside: Tilt the mower onto its side, ensuring the carburetor and air filter are facing upwards to prevent fuel or oil leakage.
  3. Remove Old Blade Holder (if applicable): If replacing an existing blade holder, carefully remove the blade bolt and then the old blade and blade holder. Note the orientation of all components.
  4. Clean Shaft: Clean any debris or rust from the engine crankshaft where the blade holder will be mounted.
  5. Position New Blade Holder: Align the new SECURA Blade Holder (Model 6922671) with the engine crankshaft. The bore of the blade holder (22.2 mm diameter) should slide onto the crankshaft. Ensure the drive lugs or bore distance (65 mm) align correctly with the blade.
  6. SECURA Blade Holder, angled view

    Image 3: Angled view of the blade holder, showing the shaft insertion depth and overall height.

  7. Install Blade: Place the lawn mower blade onto the blade holder, ensuring it is correctly seated on the drive lugs. The blade's cutting edge should face the direction of rotation.
  8. Secure with Bolt: Insert the blade bolt through the blade and into the blade holder's screw bore (18 mm diameter). Tighten the bolt securely according to your mower's manufacturer specifications, typically using a torque wrench.
  9. Verify Installation: Double-check that the blade holder and blade are firmly attached and rotate freely without obstruction.
  10. Reconnect Spark Plug: Reconnect the spark plug wire.

Pre-Operation Check

Before each use of the lawn mower, perform the following checks:

  • Blade Security: Ensure the blade bolt is tight and the blade is securely fastened to the blade holder.
  • Blade Condition: Inspect the blade for sharpness, balance, and any damage. Replace or sharpen as needed.
  • Vibration: If excessive vibration occurs during operation, immediately shut off the engine and inspect the blade and blade holder for damage or improper installation.

Maintenance

Regular maintenance of the blade holder ensures optimal performance and safety:

  • Periodic Inspection: Periodically inspect the blade holder for signs of wear, cracks, or damage, especially after hitting an object.
  • Cleaning: Keep the blade holder and surrounding area free of grass clippings and debris.
  • Replacement: If the blade holder shows significant wear or damage, replace it immediately with a compatible SECURA part.

Troubleshooting

ProblemPossible CauseSolution
Excessive vibration during mowing
  • Loose blade bolt
  • Damaged or unbalanced blade
  • Damaged blade holder
  • Tighten blade bolt
  • Inspect and replace/sharpen blade
  • Inspect and replace blade holder
Blade not spinning freely
  • Debris lodged around blade holder
  • Improper installation
  • Clean debris
  • Re-install blade holder and blade correctly
Blade holder does not fit crankshaft
  • Incorrect model part
  • Crankshaft damaged or dirty
  • Verify part compatibility with mower model
  • Clean crankshaft; inspect for damage

Technical Specifications

Model Number:6922671
Compatible Mowers:MacAllister MPRM 53SP, B&S 675EXi R.S.
Engine Shaft Bore Diameter:22.2 mm
Blade Screw Bore Diameter:18 mm
Distance Between Drive Lugs/Bore:65 mm
Pulley Diameter:58 mm
Engine Shaft Insertion Depth:43 mm
Total Height:66 mm
Year of Construction (Mower):2016 (for compatible mowers)
SECURA Blade Holder, bottom view

Image 4: Bottom view of the SECURA Blade Holder, showing the pulley diameter and internal structure.

Warranty and Support

For warranty information or technical support regarding your SECURA Blade Holder, please contact the manufacturer or your point of purchase. Keep your purchase receipt as proof of purchase.

Manufacturer: SECURA

For further assistance, you may visit the Secura brand page on Amazon.

© 2023 SECURA. All rights reserved. This manual is subject to change without notice.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.