Introduction
This document provides instructions for the Generic Easytry21930 infrared replacement remote control. This remote is designed to operate various Sanyo LED HDTV, CRT, VCR, and DVD Combo Color TV models, including FXWD, FXWE, FXWG, FXWK, FXWB, FXWC, FXRB, DS31590, DS20930, DS35590, and DS27930. Please ensure your original remote has the same button layout as this replacement for full compatibility.
This remote control operates using infrared (IR) technology and requires batteries for operation. No programming is typically required; simply insert batteries and point towards your device.
Product Overview
The Generic Easytry21930 remote control features a standard layout for television and VCR/DVD combo functions. It is designed for ease of use with clearly labeled buttons.
Figure 1: Front view of the remote control, displaying the button layout for various functions.
Figure 2: Back view of the remote control, showing the open battery compartment designed for two AA batteries.
Setup
Battery Installation
- Locate the battery compartment on the back of the remote control.
- Slide the battery compartment cover downwards or press the latch and lift to open.
- Insert two (2) AA batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
- Replace the battery compartment cover by sliding it back into place until it clicks securely.
Note: Batteries are not included with the remote control. Always use new, high-quality batteries for optimal performance.
Operating Instructions
This remote control is designed to function as a direct replacement for your original Sanyo remote. No complex programming is required. Simply point the remote at the infrared receiver on your Sanyo television or VCR/DVD combo unit.
Basic Functions:
- POWER: Turns the device on or off.
- INPUT: Cycles through available video input sources (e.g., TV, AV1, HDMI).
- VOL +/-: Adjusts the volume level.
- CH +/-: Changes the channel up or down.
- Number Pad (0-9): Directly enters channel numbers.
- MUTE: Silences the audio.
- MENU: Accesses the device's on-screen menu.
- PLAY, STOP, REC, PAUSE: Controls for VCR or DVD playback functions.
Important Compatibility Note: For this remote to function correctly, your original remote control must have the same button layout and functions as depicted in the product images. If your original remote differs significantly, this replacement may not be fully compatible or offer all desired functions.
Maintenance
Battery Replacement
When the remote control's range decreases or buttons become unresponsive, it is likely time to replace the batteries. Follow the battery installation steps outlined in the "Setup" section. Always replace both batteries simultaneously with new ones of the same type (AA).
Cleaning
To clean the remote control, gently wipe its surface with a soft, dry cloth. For stubborn dirt, slightly dampen the cloth with water or a mild, non-abrasive cleaner. Avoid using harsh chemicals or excessive moisture, as these can damage the remote's electronics.
Remove batteries if the remote will not be used for an extended period to prevent leakage and potential damage.
Troubleshooting
- Remote not responding:
- Ensure batteries are inserted correctly with the correct polarity.
- Replace old batteries with new ones.
- Check for any obstructions between the remote control and the device's IR receiver.
- Ensure you are within the effective operating range (up to 8 meters).
- Certain buttons not working:
- Verify that your original remote had the same specific button or function. This replacement remote may not support all advanced or unique functions of every Sanyo model.
- Clean the remote's surface, especially around the unresponsive buttons, to remove any dirt or debris.
- Device not turning on/off:
- Confirm the device is plugged into a power source and is not in standby mode due to a power outage.
If troubleshooting steps do not resolve the issue, please refer to the "Warranty and Support" section for further assistance.
Specifications
| Brand | Generic |
| Model Number | Easytry21930 |
| Connectivity Technology | Infrared (IR) |
| Compatible Devices | Television (Sanyo LED HDTV, CRT, VCR, DVD Combo Color TV models) |
| Maximum Number of Supported Devices | 1 |
| Maximum Range | 8 Meters |
| Number of Batteries Required | 2 |
| Battery Type | AA |
| Color | Grey |
| Special Feature | Ergonomic design; direct replacement (requires matching button layout) |
Warranty and Support
Warranty Information
This product comes with a 90-day warranty. This warranty covers manufacturing defects and ensures hassle-free returns within the specified period. Please retain your proof of purchase.
Customer Support
If you encounter any issues that cannot be resolved using the troubleshooting guide, or if you have questions regarding compatibility with your specific Sanyo model, please contact the seller directly through the platform where the purchase was made. Provide your model number and a detailed description of the issue for prompt assistance.
For model number verification, please refer to the label on your original device or its user manual. The remote's compatibility is primarily based on matching the button layout with your original remote.