Amewi Hyper GO Truggy 1:14 Brushless 4WD RC Vehicle Instruction Manual

1. Important Safety Information

Please read this manual carefully before operating the Amewi Hyper GO Truggy. Failure to follow these instructions may result in injury or damage to the product.

• Warning! Not suitable for children under three years of age. Choking hazard due to small parts.
• Recommended age for operation: Adolescents and Adults (14+ years).
• Always operate the vehicle in a safe, open area, away from people, pets, and obstacles.
• Do not operate near public roads, water, or high-voltage power lines.
• Keep hands, hair, and loose clothing away from moving parts.
• Ensure all electronics are protected from water splashes during outdoor use.
• Never leave the battery charging unattended.
• Use only the provided charging cable and compatible power sources.

2. Package Contents

The Amewi Hyper GO Truggy RTR (Ready-To-Run) package includes the following components:

• Amewi Hyper GO Truggy (Model 22659)
• 3-Channel 2.4 GHz Remote Control
• 2S LiPo Battery (7.4V, 3000mAh, 25C)
• USB Balance Charging Cable (7.4V, 1.5A output)
• Additional Gold-colored Body Shell
• Set of Sand Tires
• Spare Parts (e.g., front wishbones, body mounts, spare rear wing)
• Tool Kit (e.g., screw set)
• Body Clips with Rubber Tabs
• Instruction Manual (this document)

Note: Two AA 1.5V batteries for the remote control are required and not included in the package.

3. Setup

3.1. Charging the LiPo Battery

The included LiPo battery must be fully charged before first use. Always follow LiPo battery safety guidelines.

1. Connect the USB balance charging cable to a compatible USB power adapter (not included).
2. Connect the LiPo battery to the charging cable. Ensure the connectors are correctly aligned.
3. The charging indicator on the cable will show the charging status (e.g., red for charging, green for fully charged).
4. Charging time is approximately 150-180 minutes. Do not overcharge.
5. Once charged, disconnect the battery from the charger and store it safely.

Image: The included 2S 7.4V 3000mAh LiPo battery for the Amewi Hyper GO Truggy.

3.2. Installing Remote Control Batteries

Insert two AA 1.5V batteries (not included) into the remote control's battery compartment. Ensure correct polarity.

3.3. Installing the Vehicle Battery

1. Remove the body clips and carefully lift the vehicle's body shell.
2. Place the charged LiPo battery into the battery compartment.
3. Connect the battery to the vehicle's ESC (Electronic Speed Controller) connector.
4. Secure the battery if necessary and reattach the body shell with the clips.

4. Operating Instructions

4.1. Powering On and Pairing

1. Turn on the remote control first.
2. Turn on the vehicle's power switch.
3. The remote control and vehicle should automatically pair. If not, refer to the troubleshooting section.

4.2. Basic Controls

• Steering Wheel: Turn left or right to control the vehicle's direction.
• Throttle Trigger: Pull to accelerate forward, push to brake or reverse.
• Trim Adjustments: Use the steering trim and throttle trim dials on the remote control to fine-tune straight-line tracking and neutral throttle position.
• Headlights: The 3-channel remote control features an additional button to turn the front LED headlights on or off.

4.3. Speed Limiter

The remote control includes a switch to limit the maximum speed to 70%. This is useful for beginners or when operating in smaller spaces.

4.4. Driving Tips

• Start with slow speeds to get accustomed to the controls.
• The vehicle is equipped with large, high-grip soft rubber tires for excellent traction on various surfaces.
• For sand driving, utilize the included sand tires for optimal performance.
• The Wheelie Bar provides increased driving stability, especially during rapid acceleration.
• The 2.4 GHz system allows multiple models to operate simultaneously without interference.

Image: The Amewi Hyper GO Truggy in its standard black body, ready for operation.

5. Maintenance

Regular maintenance ensures the longevity and performance of your Amewi Hyper GO Truggy.

• Cleaning: After each use, especially in dusty or dirty conditions, clean the vehicle with a soft brush or compressed air. Avoid using water directly on electronics.
• Inspection: Regularly check for loose screws, damaged parts, or worn tires. Tighten screws as needed.
• Drive Components: The drive components (gears and differentials) are made of metal for high durability. Inspect them periodically for wear and lubricate if necessary.
• Shock Absorbers: The aluminum oil-pressure shock absorbers should be checked for leaks or damage.
• Motor Fan: The active fan on the motor ensures optimal cooling. Keep it free from debris.
• Battery Storage: Store LiPo batteries in a cool, dry place at a storage voltage (around 3.8V per cell) if not used for extended periods.

6. Troubleshooting

If you encounter issues with your Amewi Hyper GO Truggy, refer to the following common problems and solutions:

7. Specifications

8. Warranty and Support

8.1. Manufacturer's Warranty

Manufacturer's warranty information is not explicitly specified in the product details. Please retain your proof of purchase for any warranty claims. For specific warranty terms, contact Amewi directly.

8.2. Customer Support

For technical assistance, spare parts, or further inquiries, please contact Amewi customer support. Refer to the official Amewi website or product packaging for the most up-to-date contact information.

Amewi GmbH
Address: [Refer to official Amewi website for current address]
Website: www.amewi.com