Introduction
Thank you for choosing the Generic KL22G-64T TV Mount. This mount is designed to securely hold flat-panel televisions ranging from 37 to 70 inches, supporting VESA patterns up to 600x400mm, and features a tilt function for optimal viewing angles. Please read this manual thoroughly before installation to ensure safe and correct setup.
Package Contents
Verify that all components are present and undamaged. If any parts are missing or defective, please contact customer support.
- Wall Plate (A)
- TV Brackets (B x2)
- Mounting Hardware Kit (C) - Includes various screws, washers, spacers, and anchors.
- Instruction Manual (This document)
Image: All components included in the KL22G-64T TV Mount package.
Important Safety Information
WARNING: Failure to read and follow these instructions may result in serious personal injury, property damage, or voiding of your warranty. If you do not understand these instructions or have doubts about the safety of the installation, please contact a qualified installer.
- Do not install this product on a wall that is not structurally sound.
- Ensure the mounting surface can safely support the combined weight of the mount and your television.
- Always use a stud finder to locate wood studs or consult a professional for concrete/brick wall installations.
- Do not exceed the maximum weight capacity of 45 kg (99 lbs).
- This product is intended for indoor use only.
- Keep children and pets away during installation.
Setup and Installation
Tools Required (Not Included)
- Phillips Head Screwdriver
- Drill with appropriate drill bits (e.g., 10mm for concrete/brick, 5.5mm for wood studs)
- Stud Finder
- Level
- Measuring Tape
- Pencil
- Hammer (for concrete anchors)
Step 1: Attaching TV Brackets to Your TV
Carefully place your TV face-down on a soft, clean surface to prevent screen damage.
- Identify the VESA mounting holes on the back of your TV.
- Select the correct diameter and length of screws (M4, M6, or M8) from the hardware kit (C) that fit your TV's mounting holes. Use washers and spacers if necessary to ensure a snug fit without overtightening.
- Attach the two TV Brackets (B) to the back of your TV using the selected screws. Ensure the brackets are centered and level, with the hooks facing downwards.
Image: Attaching the TV brackets to the rear of the television.
Step 2: Mounting the Wall Plate to the Wall
Determine the desired height for your TV. Use a level and pencil to mark the drilling locations.
- For Wood Stud Installation: Use a stud finder to locate the center of two adjacent wood studs. Position the Wall Plate (A) against the wall, ensuring it is level, and mark the drilling points within the studs. Drill pilot holes (approx. 5.5mm diameter) into the studs. Secure the Wall Plate (A) using the lag bolts and washers provided in hardware kit (C).
- For Concrete/Brick Wall Installation: Position the Wall Plate (A) against the wall, ensuring it is level, and mark the drilling points. Drill pilot holes (approx. 10mm diameter) to a depth of at least 50mm. Insert the concrete anchors into the drilled holes, tapping gently with a hammer if needed. Secure the Wall Plate (A) using the lag bolts and washers into the anchors.
Image: Securing the wall plate to the chosen mounting surface.
Step 3: Mounting the TV to the Wall Plate
This step typically requires two people for safety.
- Carefully lift the TV with the attached brackets.
- Align the hooks on the TV Brackets (B) with the top edge of the Wall Plate (A).
- Gently lower the TV, ensuring the brackets engage securely with the wall plate. You should hear a click or feel the TV settle into place.
- Locate the safety screws or locking mechanisms on the bottom of the TV Brackets. Tighten these screws to prevent the TV from accidentally lifting off the wall plate.
Image: Hanging the television onto the wall plate and securing it.
Operating Instructions
Adjusting Tilt Angle
The KL22G-64T mount allows for easy tilt adjustment to reduce glare and optimize your viewing experience.
- To adjust the tilt, gently push the bottom of the TV forward or pull it back to achieve the desired angle.
- Some models may have knobs or levers on the side of the TV brackets that need to be loosened before tilting and tightened afterward to secure the angle. Refer to the specific design of your TV brackets.
Maintenance
Regular maintenance ensures the longevity and safety of your TV mount.
- Periodically check all screws and bolts to ensure they are tight and secure. Do not overtighten.
- Inspect the mount for any signs of wear, damage, or corrosion.
- Clean the mount with a soft, dry cloth. Avoid abrasive cleaners or solvents.
- If you notice any issues, discontinue use and contact customer support.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| TV is not level | Wall plate or TV brackets are not level. | Remove TV, re-level wall plate or adjust TV brackets if possible. Ensure all screws are tightened evenly. |
| TV feels unstable | Mounting screws are loose; incorrect anchors used; wall not strong enough. | Check all mounting screws for tightness. Verify correct anchors were used for your wall type. Consult a professional if wall strength is a concern. |
| Cannot tilt TV | Tilt mechanism is too tight or locked. | Loosen any tilt adjustment knobs or bolts on the TV brackets. Refer to operating instructions. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | KL22G-64T (Mfr Part Number: BSL502688BK) |
| Mounting Type | Wall Mount |
| Movement Type | Tilt |
| Brand | Generic |
| Material | Metal |
| Compatible Devices | Television |
| Minimum Supported Screen Size | 37 Inches |
| Maximum Supported Screen Size | 70 Inches |
| VESA Compatibility | Up to 600x400mm (Max) |
| Weight Capacity | 45 kg (99 lbs) |
Warranty and Support
This Generic TV Mount comes with a limited warranty against defects in materials and workmanship. Please refer to the warranty card included in your package or visit our website for detailed terms and conditions. Keep your purchase receipt as proof of purchase.
For technical assistance, missing parts, or warranty claims, please contact our customer support team:
- Email: support@genericmounts.com
- Phone: 1-800-XXX-XXXX (Monday-Friday, 9 AM - 5 PM EST)
- Website: www.genericmounts.com/support
Note: As no specific warranty or support information was provided, generic contact details are used as placeholders.
