Introduction
Thank you for choosing the LUNINO H13 HEPA Air Purifier E-200. This advanced air purification system is designed to effectively capture 99.97% of airborne contaminants, including pet hair, smoke, PM 2.5, and unpleasant odors, ensuring a healthier living environment. Its wide coverage area makes it ideal for various spaces such as bedrooms, living rooms, offices, nurseries, basements, and kitchens.
Image: LUNINO H13 HEPA Air Purifier E-200 in white, showcasing its sleek design.
Product Overview Video
Video: A comprehensive overview of the LUNINO H13 HEPA Air Purifier, demonstrating its features and design.
Key Features
- High Efficiency HEPA Filtration: Captures 99.97% of airborne contaminants, including pet hair, smoke, PM 2.5, and bad smells.
- Large Room Coverage: Effectively purifies air in areas up to 2400 sq.ft.
- Multiple Fan Modes: Features 5 fan speed modes (Sleep/Auto/Low/Med/High) for customized airflow and noise levels as low as 15dB in Sleep mode.
- Aromatherapy Function: Add essential oils to the dedicated pad for a pleasant scent.
- Air Quality Display: Real-time PM2.5 levels and indicator light (Green: Good, Yellow: Normal, Red: Bad).
- Timer Function: Set operation for 2, 4, 8, or 12 hours for energy saving.
- Child Lock: Prevents accidental changes to settings.
- Filter Replacement Reminder: Indicator light notifies when filter replacement is needed.
Image: Diagram illustrating the 2400 sq.ft. coverage area and CADR of 300 m³/h.
Image: Air purifier operating in sleep mode with a baby sleeping peacefully, highlighting its quiet operation (15dB).
Setup
- Unpack the Air Purifier: Carefully remove the air purifier and all accessories from the packaging.
- Remove Filter Packaging: The H13 HEPA filter comes pre-installed but is sealed in plastic packaging for protection.
- Locate the front panel of the air purifier.
- Gently pull the front panel to detach it from the main unit.
- Carefully remove the filter from its compartment.
- Remove all plastic packaging from the filter.
- Reinstall the Filter: Place the filter back into the air purifier with the "OUTWARD" side facing you. Ensure it fits snugly.
- Reattach the Front Panel: Align the front panel with the unit and push it gently until it clicks into place.
- Connect to Power: Plug the power cord into a suitable electrical outlet.
- Initial Preheating: Upon first power-on, the air purifier will enter a preheating state, and the indicator light may flash for approximately one minute. This is normal.
Image: Visual representation of the filter removal and installation process, showing the filter's effectiveness.
Operating Instructions
Control Panel Overview
The control panel is located on the top of the unit and features intuitive touch buttons for easy operation.
Image: Close-up of the control panel showing the Air Quality Display and various function buttons.
Functions:
- On/Off Button: Press to turn the air purifier on or off.
- Speed Button: Cycles through Sleep, Low, Medium, and High fan speeds.
- Sleep Mode: Operates at a quiet 15dB, ideal for undisturbed rest.
- Auto Mode (A): The air purifier automatically adjusts fan speed based on real-time air quality detected by the PM2.5 sensor.
- Light Button: Toggles the ambient light on/off. Useful for bedrooms at night.
- Timer Button: Sets the operating duration to 2, 4, 8, or 12 hours. The unit will automatically shut off after the set time.
- Lock Button: Long press to activate/deactivate the child lock, preventing accidental changes to settings.
- Aromatherapy Pad: Located on the top surface. Slide open the cover and add a few drops of your favorite essential oil to the cotton pad. The fan will diffuse the scent into the room.
Maintenance
Filter Replacement
The air purifier has a filter replacement reminder function. When the filter reaches the end of its service life (recommended every 3-6 months depending on usage), the filter replacement indicator light will illuminate.
- Turn off and unplug the air purifier.
- Remove the front panel and the old filter as described in the Setup section.
- Dispose of the old filter properly.
- Install a new official LUNINO H13 HEPA filter (search B0CMC2HHZH on Amazon). Ensure the "OUTWARD" side faces you.
- Reattach the front panel.
- Plug in and turn on the air purifier. The filter replacement indicator light should reset.
Cleaning
- Wipe the exterior of the air purifier with a soft, dry cloth.
- The pre-filter layer of the H13 HEPA filter can be gently vacuumed to remove larger dust particles between replacements. Do not wash the filter.
Troubleshooting
- Unit not turning on: Ensure the power cord is securely plugged into both the unit and the wall outlet. Check if the filter is correctly installed and its plastic packaging removed.
- Reduced airflow or unusual noise: Check if the filter is clogged and needs cleaning or replacement. Ensure there are no obstructions around the air intake or outlet.
- Air quality reading remains "Bad": Ensure the air quality sensor on the side of the unit is not obstructed or dirty. Clean the sensor area if necessary.
Specifications
| Attribute | Value |
|---|---|
| Brand | LUNINO |
| Model Number | E-200 |
| Product Dimensions | 6.26"D x 11.77"W x 16.14"H |
| Item Weight | 6.61 Pounds |
| Floor Area Coverage | Up to 2400 Square Feet |
| Filter Type | H13 HEPA |
| Noise Level (Sleep Mode) | As low as 15dB |
| Certifications | ETL Certified, CARB Certified, EPA Certified |
Warranty and Support
LUNINO is committed to providing reliable products and excellent customer service. Your LUNINO H13 HEPA Air Purifier E-200 comes with:
- 2 Years Free Replacement: For any manufacturing defects.
- 30 Days No Reason to Return Policy: For your peace of mind.
- Lifetime Support: Dedicated support to ensure your satisfaction.
- 24 Hours Quick Response: Via phone or email for any inquiries.
For support, please refer to the contact information provided in your product packaging or visit the official LUNINO store on Amazon.
