RecPro RP-1802

RecPro RV Speaker Switch 3-Position Control Panel User Manual

Model: RP-1802

Introduction

Thank you for choosing the RecPro RV Speaker Switch 3-Position Control Panel. This manual provides essential information for the proper installation, operation, and maintenance of your speaker switch. This device allows you to easily switch between interior and exterior speakers, or play audio through both simultaneously, enhancing your RV audio experience. Its low-profile black design integrates seamlessly with most RV interiors.

What's in the Box

  • RecPro RV Speaker Switch (Model: RP-1802)

Product Overview

The RecPro RV Speaker Switch features a simple, intuitive design for controlling your RV's audio output.

RecPro RV Speaker Switch front view

Figure 1: Front view of the RecPro RV Speaker Switch, showing the labeled twist knob for speaker selection.

The front panel includes a single twist knob with three clearly marked positions:

  • IN: Directs audio to the interior speakers only.
  • BOTH: Directs audio to both interior and exterior speakers simultaneously.
  • OUT: Directs audio to the exterior speakers only.
RecPro RV Speaker Switch with feature callouts

Figure 2: The speaker switch highlighting its easy-to-use design and ability to control interior, exterior, or both speaker zones.

Installation

Mounting the Switch

The RecPro RV Speaker Switch is designed for flush mounting. Ensure you have adequate space behind the mounting surface for wiring connections.

  • Choose a suitable location in your RV, typically near your audio head unit.
  • Refer to the dimensions below to create a rough opening for the switch.
  • Insert the switch into the opening and secure it using appropriate fasteners (not included) through the mounting holes on the faceplate.
RecPro RV Speaker Switch dimensions and rough opening

Figure 3: Detailed measurements for the RecPro RV Speaker Switch, including the rough opening dimensions for installation.

Wiring Instructions

The speaker switch connects to your audio head unit and both sets of speakers (interior and exterior). It uses screw terminals for secure connections. Important: Disconnect all power to your audio system before beginning installation to prevent electrical shock or damage to components.

Back view of RecPro RV Speaker Switch showing wiring harness

Figure 4: Rear view of the speaker switch, showing the pre-attached wiring harness for connection.

Refer to the wiring diagram below for correct connections. Each wire is color-coded and labeled for clarity.

RecPro RV Speaker Switch wiring diagram

Figure 5: Comprehensive wiring diagram for the RecPro RV Speaker Switch (Model RP-1802), illustrating connections for radio and both interior and exterior speakers.

  1. Identify Speaker Wires: Your RV's audio system will have positive (+) and negative (-) wires for each speaker channel (Left and Right, Interior and Exterior).
  2. Connect Radio Output:
    • Connect the Orange (RADIO L+) wire from the switch to your radio's Left Positive (+) output.
    • Connect the Black (RADIO L-) wire from the switch to your radio's Left Negative (-) output.
    • Connect the Blue (RADIO R+) wire from the switch to your radio's Right Positive (+) output.
    • Connect the Gray (RADIO R-) wire from the switch to your radio's Right Negative (-) output.
  3. Connect Interior Speakers:
    • Connect the Green (INSIDE L+) wire from the switch to your interior Left Positive (+) speaker wire.
    • Connect the White (INSIDE L-) wire from the switch to your interior Left Negative (-) speaker wire.
    • Connect the Yellow (INSIDE R+) wire from the switch to your interior Right Positive (+) speaker wire.
    • Connect the Red (INSIDE R-) wire from the switch to your interior Right Negative (-) speaker wire.
  4. Connect Exterior Speakers:
    • Connect the Light Blue (OUTSIDE L+) wire from the switch to your exterior Left Positive (+) speaker wire.
    • Connect the Teal (OUTSIDE L-) wire from the switch to your exterior Left Negative (-) speaker wire.
    • Connect the Pink (OUTSIDE R+) wire from the switch to your exterior Right Positive (+) speaker wire.
    • Connect the Brown (OUTSIDE R-) wire from the switch to your exterior Right Negative (-) speaker wire.
  5. Secure Connections: Ensure all connections are tight and properly insulated to prevent short circuits.
  6. Restore Power: Once all connections are verified, restore power to your audio system.

Operating Instructions

Using the RecPro RV Speaker Switch is straightforward. Simply turn the knob to select your desired audio output.

  • IN Position: Rotate the knob to "IN" to play audio exclusively through your RV's interior speakers.
  • BOTH Position: Rotate the knob to "BOTH" to play audio through both your interior and exterior speakers simultaneously.
  • OUT Position: Rotate the knob to "OUT" to play audio exclusively through your RV's exterior speakers.

Adjust the volume using your RV's main audio head unit. The speaker switch does not control volume.

Maintenance

The RecPro RV Speaker Switch requires minimal maintenance.

  • Keep the unit clean by wiping it with a soft, dry cloth. Avoid abrasive cleaners or solvents.
  • Periodically check wiring connections to ensure they remain secure, especially after long periods of travel or vibration.
  • Ensure no moisture or liquids come into contact with the internal components.

Troubleshooting

Problem Possible Cause Solution
No sound from any speakers.
  • Audio head unit is off or muted.
  • Incorrect wiring from radio to switch.
  • Power issue with audio system.
  • Ensure head unit is on and volume is up.
  • Verify all "RADIO" connections to the switch are correct as per the wiring diagram.
  • Check fuses and power supply to your audio system.
Sound only from interior/exterior speakers when "BOTH" is selected.
  • Incorrect wiring for one set of speakers.
  • Faulty speaker(s).
  • Check the "INSIDE" and "OUTSIDE" speaker connections on the switch against the wiring diagram. Ensure positive and negative wires are correctly matched.
  • Test individual speakers if possible.
Distorted or low sound.
  • Loose or corroded wiring connections.
  • Improper impedance matching (less common with simple switches).
  • Inspect all wiring connections for tightness and corrosion. Re-secure if necessary.
  • Ensure your speakers are compatible with your head unit's output.

Specifications

Feature Detail
Model Number RP-1802
Brand RecPro
Package Dimensions 6.02 x 5.12 x 1.77 inches
Item Weight 2.08 ounces
Operation Mode Manual
Contact Type Normally Open
Connector Type Screw Terminals
Circuit Type 3-way
Actuator Type Rotary Knob
Contact Material Copper, Brass
International Protection Rating IP00
Number of Positions 3 (IN, BOTH, OUT)

Warranty Information

For specific warranty details regarding your RecPro RV Speaker Switch, please refer to the warranty documentation included with your purchase or visit the official RecPro website. Keep your proof of purchase for warranty claims.

Customer Support

If you have any questions, require technical assistance, or need to report an issue with your RecPro RV Speaker Switch, please contact RecPro customer support.

You can typically find contact information on the official RecPro website: RecPro Store on Amazon.

© 2024 RecPro. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.