1. Introduction
The ID-COOLING SE-207-XT Slim is a high-performance dual-tower CPU air cooler designed to provide efficient heat dissipation for a wide range of Intel and AMD processors. Featuring 7 heat pipes and a 120mm PWM fan, this cooler ensures optimal thermal management for your system. Its slim 135mm height allows for compatibility with most tower cases, while its design ensures no overhang on RAM or PCIe slots on most current motherboards.
2. Product Overview
The SE-207-XT Slim CPU cooler is engineered for superior cooling performance and quiet operation. Its dual-tower design maximizes surface area for heat exchange, while the included 120mm PWM fan provides excellent airflow and pressure.
Key Features:
- Better Heat Dissipation: Dual-tower design with 7 heat pipes and a 120mm PWM fan for excellent heat transfer. Supports two additional fans for enhanced cooling.
- High-efficient Fan: 120mm PWM fan delivers improved pressure and airflow (Max. Air Flow: 76.16CFM) with low noise.
- RAM Compatibility: Designed to avoid overhang on RAM or PCIe slots on most motherboards.
- Compact Height: 135mm height fits most tower cases.
- Broad Compatibility: Supports Intel LGA1700/1200/1150/1151/1155/1156 and AMD AM5/AM4 sockets.
- Extra Fan Allowed: Flexible fan configuration for quiet, balanced, or extreme modes (2 extra fan clips included).
Product Components:
The image above shows the complete ID-COOLING SE-207-XT Slim CPU Cooler, highlighting its dual-tower heatsink design and the central 120mm fan. The all-black finish provides a sleek aesthetic.
This image displays all the components included with the SE-207-XT Slim cooler, such as the heatsink, cooling fan, various mounting brackets for different CPU sockets, screws, standoffs, thermal paste, and a screwdriver, ensuring a complete installation kit.
Product Showcase Video:
Video 2.1: SE-207-XT Slim Product Showcase
This video provides a dynamic overview of the ID-COOLING SE-207-XT Slim CPU cooler, showcasing its design, components, and how it looks when installed in a PC system. It highlights the aesthetic and structural features of the cooler.
3. Specifications
Below are the detailed specifications for the ID-COOLING SE-207-XT Slim CPU Cooler:
| Specification | Value |
|---|---|
| Product Dimensions | 4.72 x 4.33 x 5.31 inches (120 x 110 x 135 mm) |
| Weight | 2.2 Pounds (760g heatsink and fan only) |
| Item Model Number | SE-207-XT SLIM |
| Manufacturer | ID-COOLING |
| Country of Origin | China |
| Power Connector Type | 4-Pin PWM |
| Voltage | 12 Volts |
| Wattage (TDP) | 220 watts |
| Cooling Method | Air |
| Compatible Devices | Desktop CPUs |
| Noise Level | 15.2-35.2 dB(A) |
| Maximum Rotational Speed | 700-1800 RPM (PWM) |
| Air Flow Capacity | 76.16 Cubic Feet Per Minute (CFM) |
| Bearing Type | Hydraulic Bearing |
| Heat Pipes | 7 |
This image provides a detailed specification table for the cooler, including dimensions, fan speed, noise level, and airflow, presented in multiple languages.
Supported CPU Sockets:
- Intel: LGA2066 / 2011 / 1700 / 1200 / 115X (1150, 1151, 1155, 1156)
- AMD: AM5 / AM4
This image visually confirms the list of compatible Intel and AMD CPU sockets for the SE-207-XT Slim cooler.
4. Installation Guide
Before beginning installation, ensure your system is powered off and unplugged. Refer to your motherboard manual for specific details regarding CPU socket and component placement. Always handle components with care to prevent damage.
4.1. General Preparation
- Unpack all components and verify contents against the parts list (refer to Figure 2.2).
- Ensure the CPU is correctly seated in its socket.
- Clean any old thermal paste from the CPU surface and the cooler's base if replacing an existing cooler.
4.2. Intel LGA1200 / LGA115X Installation
Follow these steps for installing the cooler on Intel LGA1200 or LGA115X motherboards:
- Step 1: Put the Intel backplate through the back of the motherboard.
- Step 2: Put on the standoffs and then secure the LGA1200/115X brackets by tightening nuts.
- Step 3: Apply the thermal paste on the CPU evenly.
- Step 4: Remove the protective sticker from the cooler's base and carefully place the cooler onto the CPU. Secure it with the provided screws.
- Step 5: Secure the fan to the heatsink with the 2 fan clips.
- Step 6: Connect the fan power cable to the "CPU_FAN" header on the motherboard.
Video 4.1: Intel LGA1200 / LGA115X Installation Guide
This video demonstrates the step-by-step installation process for the ID-COOLING SE-207-XT Slim CPU cooler on Intel LGA1200 and LGA115X motherboards, including backplate, bracket, thermal paste application, and fan attachment.
4.3. Intel LGA1700 Installation
Follow these steps for installing the cooler on Intel LGA1700 motherboards:
- Step 1: Put the Intel backplate through the back of the motherboard.
- Step 2: Put on the standoffs and then secure the LGA1700 brackets by tightening nuts.
- Step 3: Apply the thermal paste on the CPU evenly.
- Step 4: Remove the protective sticker from the cooler's base and carefully place the cooler onto the CPU. Secure it with the provided screws.
- Step 5: Secure the fan to the heatsink with the 2 fan clips.
- Step 6: Connect the fan power cable to the "CPU_FAN" header on the motherboard.
Video 4.2: Intel LGA1700 Installation Guide
This video illustrates the installation procedure for the ID-COOLING SE-207-XT Slim CPU cooler on Intel LGA1700 motherboards, detailing the specific bracket and standoff usage for this socket type.
4.4. AMD AM5 / AM4 Installation
Follow these steps for installing the cooler on AMD AM5 or AM4 motherboards. Note: The stock backplate of the motherboard is needed.
- Step 1: Remove the plastic retention of the motherboard and keep the stock backplate.
- Step 2: Install the 4 standoffs and mount the two AMD brackets.
- Step 3: Apply the thermal paste on the CPU evenly.
- Step 4: Remove the protective sticker from the cooler's base and carefully place the cooler onto the CPU. Secure it with the provided screws.
- Step 5: Secure the fan to the heatsink with the 2 fan clips.
- Step 6: Connect the fan power cable to the "CPU_FAN" header on the motherboard.
Video 4.3: AMD AM5 / AM4 Installation Guide
This video guides you through the installation of the ID-COOLING SE-207-XT Slim CPU cooler on AMD AM5 and AM4 motherboards, emphasizing the use of the motherboard's stock backplate and specific AMD mounting hardware.
4.5. Important Installation Notes:
- Ensure even pressure when tightening screws to prevent damage to the CPU or motherboard.
- Do not overtighten screws. Tighten until snug, then give a small additional turn.
- Do not overtighten screws. Tighten until snug, then give a small additional turn.
- Verify that the fan cable is not obstructed by other components and is securely connected.
- Check for proper RAM clearance after installation. The slim design of this cooler is intended to minimize interference.
5. Operation
Once installed, the ID-COOLING SE-207-XT Slim CPU cooler operates automatically based on your motherboard's fan control settings. The 120mm PWM fan adjusts its speed according to CPU temperature, providing optimal cooling performance while minimizing noise.
5.1. Fan Control:
- The fan connects to the 4-pin CPU_FAN header on your motherboard.
- Most motherboards have BIOS/UEFI settings to configure fan curves (e.g., Silent, Standard, Performance). Adjust these settings to balance cooling performance and noise levels according to your preference.
- For optimal performance, ensure the fan is set to a PWM (Pulse Width Modulation) controlled mode.
This image provides a detailed view of the 120mm PWM fan, highlighting its design and the ID-COOLING logo at its center. The fan is crucial for moving air through the heatsink fins.
This diagram illustrates the intended airflow path through the dual-tower heatsink, showing how the fan pushes air through the fins for effective heat dissipation. Arrows indicate the direction of airflow.
6. Maintenance
Regular maintenance ensures the longevity and optimal performance of your CPU cooler.
6.1. Cleaning:
- Dust Removal: Periodically clean dust from the heatsink fins and fan blades using compressed air or a soft brush. Ensure the fan is not spinning rapidly during cleaning to prevent damage to the bearings.
- Fan Removal: The fan can be easily removed from the heatsink by detaching the fan clips for thorough cleaning.
6.2. Thermal Paste Reapplication:
- Thermal paste typically lasts for several years, but reapplication may be necessary if you notice a significant increase in CPU temperatures or if you remove the cooler for any reason.
- When reapplying, clean both the CPU IHS (Integrated Heat Spreader) and the cooler's base thoroughly with isopropyl alcohol before applying a new, thin layer of thermal paste.
This image shows the direct contact heat pipe technology at the base of the cooler, which is critical for efficient heat transfer from the CPU. Keeping this surface clean and properly covered with thermal paste is vital for performance.
7. Troubleshooting
If you encounter issues with your ID-COOLING SE-207-XT Slim CPU cooler, refer to the common problems and solutions below:
| Problem | Possible Cause | Solution |
|---|---|---|
| High CPU Temperatures | Improper thermal paste application; Loose cooler mounting; Insufficient airflow in case; Fan not spinning or spinning too slow. | Reapply thermal paste; Re-mount cooler ensuring even pressure; Improve case airflow; Check fan connection and BIOS settings. |
| Fan Noise / Vibration | Dust buildup on fan blades; Loose fan clips; Fan bearing issue; High fan speed settings. | Clean fan blades; Re-secure fan clips; If bearing issue, consider fan replacement; Adjust fan curve in BIOS/UEFI. |
| Cooler Not Fitting | Incorrect mounting bracket used; RAM or VRM heatsink interference; Case clearance issue. | Verify correct bracket for your CPU socket; Check RAM height compatibility (this cooler is slim, but some tall RAM heatsinks might still interfere); Ensure case has adequate CPU cooler clearance (135mm height). |
| PC Not Booting After Installation | Cooler overtightened, causing motherboard flex; CPU not seated correctly; Fan not connected to CPU_FAN header. | Loosen cooler mounting screws slightly and re-test; Re-seat CPU; Ensure fan is connected to the correct header. |
8. Warranty & Support
ID-COOLING products are manufactured with high-quality materials and undergo rigorous testing to ensure reliability and performance. For specific warranty terms and conditions, please refer to the warranty information provided with your purchase or visit the official ID-COOLING website.
8.1. Contact Information:
- Official Website: www.idcooling.com
- Support Email: support@idcooling.com
- Manufacturer: Shenzhen Wanjinghua Technology Co., Ltd.
This image provides details about the manufacturer, Shenzhen Wanjinghua Technology Co., Ltd., and includes contact information such as the official website and support email, along with compliance marks.
For further assistance or technical inquiries, please contact ID-COOLING support through the provided channels.