1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Delta 5SE-SBS-6-BL Wall Mounted Fold-Up Shower Seat. Please read this manual thoroughly before installation and use to ensure proper function and safety.
Figure 1: Delta 5SE-SBS-6-BL Wall Mounted Fold-Up Shower Seat. This image displays the product in its folded-down, ready-to-use position, showcasing the wood seat slats and matte black wall mounts.
2. Safety Information
Adhere to the following safety guidelines to prevent injury or damage to the product:
- Maximum Weight Capacity: This shower seat is designed to support a maximum weight of 250 lbs (113 kg). Do not exceed this limit.
- Secure Mounting: The mounting brackets must be anchored to a solid structural element such as 16-inch on-center studs, a header, masonry, brick wall, or block wall. Failure to do so may result in the seat detaching from the wall and causing injury.
- Professional Installation Recommended: If you are unsure about your wall structure or installation procedures, consult a qualified professional.
- Regular Inspection: Periodically check all mounting screws and the seat for any signs of looseness, wear, or damage. Tighten screws as necessary and replace damaged components immediately.
- Proper Use: Use the seat only for its intended purpose as a shower seat. Avoid standing on the seat or using it as a step stool.
3. Setup and Installation
Careful installation is critical for the safety and stability of your shower seat. Ensure all safety guidelines are reviewed before proceeding.
3.1 Required Tools (Not Included):
- Drill
- Drill bits appropriate for wall material and mounting hardware
- Level
- Measuring Tape
- Pencil
- Stud Finder (if mounting to studs)
- Screwdriver or Hex Key (depending on hardware)
3.2 Installation Steps:
- Identify Mounting Location: Determine the desired height for the shower seat. The wall brackets should be mounted 17 to 21 inches (43.2 to 53.3 cm) from the finished floor to the center of the upper mounting screw holes.
- Locate Solid Structure: Use a stud finder to locate wall studs if mounting to wood. For masonry or brick walls, ensure the chosen location can support the required anchors. The seat requires mounting on 16-inch (40.6 cm) center studs or equivalent solid structure.
- Mark Drill Points: Hold the mounting brackets against the wall at the desired height and location. Use a level to ensure they are perfectly horizontal. Mark the drill points for the mounting screws.
- Drill Pilot Holes: Drill pilot holes according to the size specified by your mounting hardware and wall material.
- Secure Brackets: Attach the mounting brackets to the wall using the appropriate hardware (included with the product). Ensure they are securely fastened and do not wobble.
- Attach Seat: Align the fold-up seat mechanism with the installed wall brackets and secure it according to the manufacturer's instructions provided with the hardware.
- Test Stability: Gently apply pressure to the seat to ensure it is stable and securely mounted before full use.
Figure 2: Product Dimensions. This image illustrates the key dimensions of the shower seat: Depth 13 inches, Width 20 inches, and Height 4.25 inches (when folded). It also reiterates the 250 lbs weight capacity and 16-inch center stud mounting requirement.
Figure 3: Installed Fold-Up Shower Seat. This image shows the shower seat installed in a shower environment, demonstrating its functional, folded-down position and how it integrates into the space.
4. Operating Instructions
The Delta 5SE-SBS-6-BL shower seat is designed for simple and convenient use.
- To Deploy the Seat: Gently pull the seat downwards from its folded-up position until it locks securely into the horizontal position. Ensure it is fully extended and stable before sitting.
- To Fold Up the Seat: Lift the seat upwards until it clicks into its vertical, folded position against the wall. This saves space when the seat is not in use.
5. Maintenance
Regular cleaning and inspection will prolong the life and appearance of your shower seat.
- Cleaning: Clean the wood seat and matte black components with a soft, damp cloth and mild soap. Avoid abrasive cleaners, harsh chemicals, or scouring pads, as these can damage the finish.
- Drying: After cleaning or use, wipe the seat dry to prevent water spots and maintain the wood's condition.
- Inspection: Periodically check all mounting hardware for tightness. Ensure the folding mechanism operates smoothly and without excessive play. If any damage or excessive wear is observed, discontinue use and contact customer support.
6. Troubleshooting
This section addresses common issues you might encounter.
- Seat feels wobbly after installation:
- Ensure all mounting screws are fully tightened.
- Verify that the mounting brackets are securely anchored to a solid structural element (studs, masonry). If not, re-installation into a proper structural element is required.
- Seat does not fold up or down smoothly:
- Check for any obstructions in the folding mechanism.
- Ensure the seat is clean and free of debris.
- If the issue persists, contact customer support. Do not force the mechanism.
7. Specifications
| Model Number | 5SE-SBS-6-BL |
| Brand | DELTA |
| Material | Wood |
| Color | Matte Black (brackets) |
| Product Dimensions (L x W x H) | 13 x 19.25 x 4.25 inches (33 x 48.9 x 10.8 cm) |
| Item Weight | 7.1 Pounds (3.2 kg) |
| Maximum Weight Recommendation | 250 Pounds (113 kg) |
| Mounting Requirements | 16-inch center studs, header, masonry, brick wall, or block wall. Must be anchored to a solid structure. |
| Wall Bracket Mounting Height | 17-21 inches (43.2-53.3 cm) from finished floor to center of upper mounting screw holes. |
8. Warranty and Support
For warranty information and customer support, please refer to the documentation included with your purchase or visit the official Delta Faucet website. Ensure you have your model number (5SE-SBS-6-BL) available when contacting support.
Manufacturer: Delta Faucet Company
Website: www.deltafaucet.com
