Zalman P30 Micro-ATX Case Instruction Manual

1. Introduction

The Zalman P30 is a spacious Micro-ATX computer chassis designed to accommodate both Micro-ATX and Mini-ITX motherboards. It features panoramic frameless tempered glass panels for an unobstructed view of your internal components and comes with three pre-installed 120mm Addressable RGB fans for enhanced cooling and aesthetics. This manual provides essential information for the proper assembly, operation, and maintenance of your P30 case.

Figure 1: The Zalman P30 Micro-ATX Case showcasing its panoramic tempered glass and internal components with RGB lighting.

2. Safety Information

• Always disconnect the power supply from the wall outlet before performing any installation or maintenance.
• Handle tempered glass panels with care to prevent breakage. Avoid impacts or dropping the panels.
• Wear an anti-static wrist strap or frequently touch a grounded metal object to prevent electrostatic discharge (ESD) when handling internal components.
• Be cautious of sharp edges inside the chassis during installation.
• Keep the case and its components away from liquids and excessive humidity.

3. Package Contents

Verify that all listed components are included in your package:

• Zalman P30 Micro-ATX Case
• 3 x 120mm Addressable RGB Fans (pre-installed)
• Accessory Box (containing various screws, anti-vibration rings, cable ties, etc.)
• User Manual (this document)

4. Specifications

Figure 2: Detailed dimensions of the Zalman P30 chassis.

5. Setup

5.1. Motherboard Installation

The Zalman P30 supports Micro-ATX and Mini-ITX motherboards. Ensure your motherboard's form factor is compatible before proceeding.

• Remove the tempered glass side panel by gently pulling it open.
• Install the necessary motherboard standoffs. The case comes with pre-installed standoffs, and additional ones are provided in the accessory box if needed.
• Carefully place your motherboard onto the standoffs, aligning the screw holes.
• Secure the motherboard with the provided screws.

Figure 3: Motherboard compatibility for the P30 case.

5.2. Power Supply Installation

The power supply unit (PSU) is mounted at the bottom of the case.

• Slide the PSU into its designated compartment at the bottom rear of the case.
• Secure the PSU using the screws provided in the accessory box.
• Connect the necessary power cables to your motherboard and other components.

5.3. Storage Device Installation

The case supports 2.5" SSDs and 3.5" HDDs.

• Locate the storage drive bays/mounts within the chassis.
• Mount your 2.5" SSDs or 3.5" HDDs using the appropriate screws and anti-vibration rings from the accessory box.

5.4. Graphics Card Installation

The Zalman P30 supports graphics cards up to 420mm in length.

• Remove the necessary PCIe slot covers from the rear of the case.
• Insert your graphics card into the primary PCIe slot on your motherboard.
• Secure the graphics card with screws.
• Utilize the pre-installed anti-sag bracket to support heavier graphics cards. Adjust its position and height as needed.

5.5. Fan and Radiator Installation

The case comes with three pre-installed 120mm ARGB fans. Additional cooling options are available:

• Top: Supports up to 360mm radiators or 3x 120mm / 2x 140mm fans.
• Side: Supports 2x 120mm fans (pre-installed as intake).
• Rear: Supports 1x 120mm fan (pre-installed as exhaust).
• Bottom: Supports 3x 120mm / 2x 140mm fans.

Figure 4: Overview of fan specifications and pre-installed ARGB fans.

5.6. Cable Management

The Zalman P30 features enhanced cable organization to maintain a clean build.

• Route all cables through the designated cutouts and rubber grommets behind the motherboard tray.
• Use the included cable ties to bundle and secure cables, preventing interference with airflow and maintaining a tidy interior.

Figure 5: Cable management features of the P30 case.

6. Operating Instructions

After completing the assembly, ensure all connections are secure before powering on your system.

• Power On/Off: Use the power button located on the front I/O panel.
• ARGB Control: The pre-installed ARGB fans can be customized via a 3-pin header connection to your motherboard's ARGB header. Use your motherboard's software to control lighting effects.
• Front I/O: Connect peripherals to the USB-C, USB 3.0, and 3.5mm audio jacks on the front panel.

Figure 6: Front I/O panel details.

7. Maintenance

Regular maintenance helps ensure optimal performance and longevity of your PC components.

• Dust Filters: The case features magnetic dust filters on the top and bottom panels. Regularly remove and clean these filters to maintain optimal airflow and prevent dust buildup.
• Panel Removal: The panoramic tempered glass front and side panels are tool-less and easily removable for cleaning and access to internal components.

Figure 7: Instructions for removing top panel and bottom dust filter.

8. Troubleshooting

If you encounter issues, consider the following common troubleshooting steps:

• No Power: Ensure the PSU is properly connected to the wall outlet and the motherboard. Check the PSU's on/off switch.
• No Display: Verify that the graphics card is correctly seated in its PCIe slot and connected to the monitor. Check all power connections to the GPU.
• Fan/RGB Issues: Confirm that all fans and ARGB cables are securely connected to the motherboard or a dedicated controller. Check motherboard software for ARGB settings.
• Overheating: Ensure all fans are spinning correctly and dust filters are clean. Verify proper CPU cooler installation.

9. Product Video

10. Warranty and Support

Zalman products are covered by a limited warranty. Please refer to the warranty card included in your package or visit the official Zalman website for detailed warranty terms and conditions.

For technical support or customer service, please contact Zalman customer support through their official channels. Contact information can typically be found on the Zalman website or in your product documentation.