1. Introduction
This manual provides essential instructions for the safe and efficient operation, setup, and maintenance of your WJYLM Window Cleaning Robot. Please read this manual thoroughly before using the device to ensure optimal performance and safety.
2. Safety Information
Adherence to safety guidelines is crucial when operating the window cleaning robot. Failure to follow these instructions may result in damage to the device, property, or personal injury.
- UPS Power Failure Protection: The robot is equipped with an Uninterrupted Power Supply (UPS) system that provides approximately 20 minutes of backup power in case of a power outage. During this time, the robot will remain attached to the window and sound an alarm. Retrieve the robot promptly during a power failure.
- Safety Rope: Always attach the provided safety rope to a secure anchor point before operating the robot, especially for high-rise windows. This prevents the robot from falling in the event of a detachment.
- Surface Suitability: This robot is suitable for various types of glass, flat walls, tables, floors, and ceilings. It is not designed for windows with gaps, skylights, or sloping work surfaces.
- Cleaning Pads: Ensure cleaning pads are not excessively wet, as this can cause the machine to slide and fall.
- Supervision: Do not leave the robot unsupervised during operation, especially in areas accessible to children or pets.
Image: The robot's UPS power failure backup system provides 20 minutes of protection. Always secure the safety rope to a stable point before operation.
3. Package Contents
Verify that all items are present in the package:
- Window Cleaning Robot
- Power Adapter
- Cleaning Rings (pre-installed or separate)
- Cleaning Cloths/Pads
- Remote Control
- Water Spray Bottle
- Safety Harness/Rope
4. Product Features
The WJYLM Window Cleaning Robot is designed for efficient and thorough window cleaning with advanced features:
- Powerful Suction: Equipped with a brushless motor, providing 2800Pa suction force for strong adhesion and effective stain removal.
- Dual Rotating Cleaning Pads: Two 14.5cm diameter cleaning discs rotate 360° to mimic manual wiping, ensuring comprehensive cleaning.
- Precise Water Spraying: Features scientific preset water spray angles and frequencies for optimal wet cleaning.
- Intelligent Path Planning: Automatically plans cleaning paths (up and down, left and down, right and down) for systematic coverage.
- Border Detection: Precisely detects window borders to avoid collisions and ensure thorough edge cleaning.
- Compact Design: Thin and light body, weighing approximately 0.95 kg, for easy handling and maneuverability.
- UPS Power Failure Protection: Provides 20 minutes of backup power and an alarm during power interruptions.
Image: The robot features a water spray function and is controlled via a remote. It has a 30ml water tank and frame detection for path planning.
Image: Key features include 2800Pa suction, precise border detection for collision avoidance, a lightweight body of 0.95kg, and 20 minutes of UPS power failure protection.
Image: The robot utilizes 14.5cm diameter cleaning pads, designed for efficient and thorough cleaning, reaching corners effectively.
5. Setup
- Attach Cleaning Pads: Securely attach clean fabric pads to the two rotating discs on the underside of the robot. Ensure they are properly aligned and fastened.
- Connect Power: Plug the power adapter into the robot and then into a power outlet. Ensure the connection is secure.
- Attach Safety Rope: Tie the safety rope securely to the designated attachment point on the robot. Then, fasten the other end of the safety rope to a strong, stable anchor point (e.g., a sturdy furniture leg, window frame, or railing) that can withstand the robot's weight.
- Fill Water Tank (Optional): If using the water spray function, open the water tank cap and fill it with clean water or a diluted glass cleaning solution using the provided spray bottle. Close the cap tightly.
6. Operating Instructions
Follow these steps for effective window cleaning:
6.1 Initial Dry Cleaning Pass
- Prepare Surface: For windows that have not been cleaned for a long time or are very dusty, it is recommended to perform a dry cleaning pass first. Use dry fabric pads for this step. This prevents dust from mixing with water and forming streaks.
- Place Robot: Place the robot on the window surface. Ensure it adheres firmly.
- Start Cleaning: Use the remote control to start the robot. It will begin cleaning in one of the automatic modes.
- Remove Robot: Once the dry cleaning pass is complete, remove the robot from the window.
6.2 Wet Cleaning Pass
- Change Pads: Replace the dry pads with new, clean fabric pads.
- Moisten Pads: Lightly spray water or diluted glass cleaner onto each pad 2 to 3 times. Do not oversaturate the pads, as this can cause the robot to slip.
- Place Robot: Place the robot back on the window surface.
- Start Cleaning: Use the remote control to start the robot. You can activate the automatic water spray function or manually spray water as needed.
- Repeat if Necessary: If windows are still dirty after one wet pass, change to new dry pads and repeat the wet cleaning process.
Image: The robot features precise water spraying with scientific angle, frequency, and range, allowing it to wipe the glass wet without leaving traces. It can operate normally even with an empty water tank if manual spraying is preferred.
6.3 Remote Control Functions
The remote control allows you to manage the robot's operations:
Image: Remote control layout with functions: Stop/Start, Automatic cleaning up and down, Automatic cleaning left and down, Automatic cleaning right and down, Manual movement (up, down, left, right), Automatic water spray, Manual water spray.
- Stop/Start: Initiates or pauses the cleaning cycle.
- Automatic Cleaning Up and Down: Robot cleans vertically.
- Automatic Cleaning Left and Down: Robot cleans horizontally from left, then moves down.
- Automatic Cleaning Right and Down: Robot cleans horizontally from right, then moves down.
- Manual Movement: Use directional arrows to guide the robot manually (up, down, left, right).
- Automatic Water Spray: Activates the robot's internal water spray function.
- Manual Water Spray: Triggers a single spray from the robot.
Image: The robot offers independent cleaning path planning, including automatic cleaning up and then down, automatic cleaning left and then down, and automatic cleaning right and then down.
7. Maintenance
7.1 Cleaning Pads
- After each use, remove the fabric cleaning pads from the robot.
- Wash the pads with mild detergent and water. They can typically be machine washed.
- Allow pads to air dry completely before reattaching them to the robot or storing them.
- Replace worn or damaged pads to ensure optimal cleaning performance.
7.2 Robot Body
- Wipe the robot's exterior with a soft, dry cloth to remove any dust or residue.
- Do not immerse the robot in water or spray cleaning solutions directly onto its electronic components.
8. Troubleshooting
If you encounter issues with your window cleaning robot, refer to the following common solutions:
- Robot not adhering to window:
- Ensure the window surface is clean and dry before placement.
- Check if the cleaning pads are too wet; replace with drier pads if necessary.
- Verify that the power adapter is securely connected and the robot is receiving power. - Robot leaving streaks:
- Perform a dry cleaning pass first to remove loose dust.
- Ensure cleaning pads are clean and not oversaturated with water/solution.
- Use a suitable glass cleaning solution. - Robot not moving or moving erratically:
- Check for obstructions on the window surface.
- Ensure the cleaning pads are properly attached and not hindering movement.
- Verify remote control battery. - Water spray not working:
- Check if the water tank is filled.
- Ensure the spray nozzle is not clogged.
For persistent issues, contact customer support.
9. Specifications
| Specification | Value |
|---|---|
| Product Name | Robot Smart Window Cleaner |
| Model | B0CJN2JKLV |
| Product Size | 30 x 15 x 10 cm |
| Body Weight | 1 kg (approx. 0.95 kg as per image) |
| Voltage | 100 ~ 240V, 50-60Hz |
| Suction Force | 2800Pa |
| UPS Power Failure Protection Time | 20 minutes |
| Control Mode | Remote Control |
| Cleaning Direction Modes | 3 types (Up/Down, Left/Down, Right/Down) |
| Bezel Detection | Automatic |
| Fall Protection Control | UPS + Safety Rope |
10. Warranty and Support
Specific warranty information for this product is not provided in the available documentation. Please refer to your purchase receipt or contact the retailer for details regarding warranty coverage.
For technical support or further assistance, please contact WJYLM customer service through the vendor's contact information provided at the point of purchase.