1. Introduction
The Paulmann 50140 Gent 2 Smart Control Remote is a Zigbee 3.0 certified handheld transmitter designed for intuitive control of smart lighting products. This remote allows you to manage Paulmann lighting products and compatible devices from other manufacturers without requiring a dedicated app or gateway for basic functions. It provides comprehensive control options for up to 30 lamps or lighting fixtures, organized into up to four distinct groups.
This manual provides detailed instructions for setting up, operating, and maintaining your Gent 2 remote control, ensuring optimal performance and user experience.
2. Product Overview
The Gent 2 remote control features a user-friendly layout for easy access to all functions. Below is an image of the remote with its key components identified.
Figure 1: Front view of the Paulmann 50140 Gent 2 Smart Control Remote.
Key Features:
- Color Wheel: For selecting desired light colors (RGB) and adjusting white light temperature.
- S1-S7 Buttons: Programmable scene buttons for quick access to preferred lighting settings.
- Power Button: To switch connected lights on or off.
- Dimming Buttons (+/-): To increase or decrease light brightness.
- Scene/Mode Buttons: Icons (flame, fast forward, snowflake) for specific lighting effects or modes.
- Group Buttons (1-4): To select and control individual lighting groups. Red LEDs above these buttons indicate the currently active group(s).
The remote control measures approximately 13.7 cm in length, 4.5 cm in width, and 1.3 cm in thickness, weighing 55 grams. It is powered by two CR2032 batteries, which are included.
Figure 2: Packaging content showing remote dimensions and battery type.
3. Setup
3.1 Battery Installation
The Paulmann Gent 2 remote control requires two CR2032 batteries. These are typically pre-installed or included in the packaging.
- Locate the battery compartment on the back of the remote control.
- Open the compartment cover.
- Insert the two CR2032 batteries, ensuring correct polarity (+/-).
- Close the battery compartment cover securely.
3.2 Mounting Options
The remote control can be mounted in a customizable position using screws. This allows for convenient placement on a wall or other surfaces.
4. Operating Instructions
4.1 Power On/Off
Press the Power Button (circle with a vertical line) to switch the connected lighting products on or off.
4.2 Dimming Control
Use the + and - buttons to adjust the brightness of the selected lights. Press + to increase brightness and - to decrease it.
4.3 Color and White Light Adjustment
The color wheel allows for precise control over light color and white light temperature.
- For RGB Colors: Rotate your finger around the outer ring of the color wheel to select a desired color.
- For White Light: Touch the center of the color wheel to switch to white light control. Then, adjust the white light temperature (e.g., warm white to cool white) by rotating your finger.
4.4 Scene Selection
The remote features dedicated buttons for various lighting scenes or modes:
- Flame Icon: Activates a warm, flickering light effect.
- Fast Forward Icon: Cycles through dynamic lighting effects or presets.
- Snowflake Icon: Activates a cool, static light effect.
Figure 3: Remote control in a home setting, demonstrating ease of use.
5. Pairing and Group Control
5.1 Pairing via Touchlink
The Gent 2 remote uses Zigbee 3.0 Touchlink for direct pairing with compatible lighting products without a gateway.
- Ensure the lighting product you wish to pair is powered on and within close proximity (typically within 10-30 cm) of the remote control.
- Initiate the pairing mode on the lighting product (refer to the product's specific manual for instructions).
- On the Gent 2 remote, press and hold the Power Button and the Group 1 Button simultaneously for approximately 3-5 seconds until the remote's indicator light flashes.
- Once successfully paired, the light will typically flash or change color to confirm.
- Repeat for additional lights or groups as needed.
5.2 Group Control
The remote can control up to four distinct groups of lights. Red LEDs above the group buttons (1-4) indicate which group(s) are currently selected.
Figure 4: Remote control showing illuminated group LEDs.
- Select a Single Group: Press the desired group button (1, 2, 3, or 4). The corresponding red LED will illuminate. All subsequent commands will only affect lights in that group.
- Select Multiple Groups: Press multiple group buttons to control several groups simultaneously. The LEDs for all selected groups will illuminate.
- Control All Groups: To control all paired lights, ensure no specific group is selected, or press a dedicated 'All' button if available (not explicitly shown but implied by general control). Alternatively, some remotes allow holding a group button to select all.
Figure 5: Remote control being used to adjust track lighting.
6. Maintenance
6.1 Battery Replacement
When the remote's performance degrades or the indicator light no longer functions, it may be time to replace the batteries.
- Open the battery compartment as described in Section 3.1.
- Remove the old CR2032 batteries.
- Insert new CR2032 batteries, observing correct polarity.
- Close the compartment.
6.2 Cleaning
To clean the remote control, use a soft, dry cloth. Do not use abrasive cleaners, solvents, or immerse the device in water.
7. Troubleshooting
If you encounter issues with your Paulmann Gent 2 remote, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Lights do not respond to remote. | Low batteries, remote not paired, out of range, interference. | Replace batteries. Re-pair the remote with the lights (Section 5.1). Move closer to the lights. Check for other 2.4 GHz devices causing interference. |
| Pairing fails. | Light not in pairing mode, remote too far, interference. | Ensure light is in pairing mode. Bring remote very close to the light (within 10-30 cm). Try again in a different location to rule out interference. |
| Group control not working correctly. | Lights not assigned to groups, incorrect group selected. | Ensure lights are correctly assigned to desired groups. Verify the correct group button is pressed (red LED illuminated). |
8. Specifications
- Model Number: 50140
- Brand: Paulmann
- Dimensions (L x W x H): 13.7 x 4.5 x 1.3 cm
- Weight: 55 grams
- Material: Plastic
- Wireless Protocol: Zigbee 3.0
- Operating Frequency: 2.4 GHz
- Control Capacity: Up to 30 lamps/lighting products, 4 groups
- Operating Range: Up to 30 meters (unobstructed)
- Power Source: 2 x CR2032 batteries (included)
Figure 6: Technical details and certifications for the remote control.
9. Warranty
The Paulmann 50140 Gent 2 Smart Control Remote comes with a 5-year warranty. Please retain your proof of purchase for warranty claims. For specific terms and conditions, refer to the official Paulmann warranty policy.
10. Support and Further Information
For additional support, detailed product information, or to explore other Paulmann smart home products, please visit our official website:
- www.paulmann.com/zb (Specific Zigbee product information)
- www.paulmann.com (General Paulmann website)
You can also scan the QR code on the product packaging for direct access to relevant online resources.
Paulmann Licht GmbH
Quezinger Feld 2 | 31832 Springe | Germany