Skyflame 30 x 6 Inch Liner Fire Pit Pan Kit Instruction Manual

1. Product Overview

The Skyflame 30 x 6 Inch Liner Fire Pit Pan Kit is designed for creating custom outdoor fire features. This kit includes a durable stainless steel drop-in pan and burner, a spark ignition system, and a propane hose, providing a complete solution for DIY fire table projects. It is suitable for both indoor and outdoor decorative use, offering a reliable and aesthetically pleasing flame.

The Skyflame 30 x 6 Inch Liner Fire Pit Pan Kit, ready for installation.

2. Important Safety Information

Please read and understand all safety warnings and instructions before installing or operating this fire pit kit. Failure to follow these instructions could result in property damage, bodily injury, or death.

• Always maintain a safe distance from combustible materials.
• Use only approved fuel types (propane or natural gas). This kit is configured for propane gas. For natural gas application, an additional natural gas hose is required and not included.
• Ensure proper ventilation when operating the fire pit.
• Store the fire pit in a safe place when not in use.
• Do not leave the fire pit unattended during operation.
• Keep children and pets away from the fire pit.
• Do not use the fire pit in windy conditions.

3. Package Contents

Verify that all components listed below are present in your package:

• Fire pit pan and burner
• Spark ignition kit with shut-off valve and key
• Non-whistle gas line
• Air mixer
• Seal tape (Teflon tape)

Components of the spark ignition system, including the igniter and wire assembly, and the 3-inch valve key used for gas control.

The flexible gas line and the propane hose with regulator, which are part of the connection system.

4. Product Specifications

Diagram showing the dimensions of the Skyflame 30 x 6 Inch Liner Fire Pit Pan Kit, including overall length, width, and depth.

Close-up view of the fire pit pan highlighting features such as high-quality stainless steel construction, machine-drilled gas holes for even flame, a drainage hole to prevent water accumulation, and the 1/2 inch gas inlet.

5. Setup and Installation

This section outlines the steps for installing your fire pit pan kit. Ensure all gas connections are tight and leak-free.

5.1 Preparing the Fire Table

• Ensure your fire table opening is appropriately sized for the 30" x 6" pan. Refer to the dimensions diagram.
• Ensure the fire table structure can support the weight of the pan, burner, and decorative media (e.g., lava rocks, fire glass).

5.2 Connecting Gas Lines

1. Apply seal tape (Teflon tape) to all threaded gas connections to ensure a leak-free seal.


Image showing the application of seal tape (Teflon tape) to threaded gas connections to ensure a leak-free seal.

2. Connect the non-whistle gas line to the burner's gas inlet.
3. Connect the air mixer to the other end of the non-whistle gas line.
4. Attach the propane hose with regulator to the air mixer and then to your propane tank.
5. For natural gas applications, replace the propane hose and regulator with a suitable natural gas hose (not included).

5.3 Installing the Ignition System

1. Mount the igniter panel in a convenient and accessible location on your fire table.


The igniter panel with its control knob and valve key slot, along with the separate valve key.

2. Connect the igniter wire to the spark igniter electrode located on the burner.


A close-up of the spark igniter component.

3. An extra mounting plate is provided for optional igniter placement if needed.


Image showing the extra mounting plate for an optional igniter, demonstrating how it can be attached to the fire pit pan.

5.4 Final Assembly

1. Place the fire pit pan into the prepared opening in your fire table.
2. Distribute your chosen decorative media (fire glass, lava rocks, etc.) evenly over the burner, ensuring not to block the igniter or gas holes.


Examples of decorative media such as fire glass, lava rocks, ceramic wood logs, and ceramic fire balls that can be used with the fire pit.

Schematic diagram illustrating the installation process of the fire pit pan kit into a fire table, showing connections for the fire pit pan, spark igniter, air mixer, and propane gas tank.

6. Operating Instructions

6.1 Ignition

1. Ensure all gas connections are secure and the propane tank valve is open.
2. Insert the valve key into the igniter panel's valve slot.
3. Slowly turn the valve key counter-clockwise to allow gas flow.
4. Immediately press and hold the igniter button to create a spark.
5. If the flame does not ignite within 5 seconds, turn off the gas, wait 5 minutes, and repeat the ignition process.

6.2 Flame Adjustment

Once ignited, you can adjust the flame height by slowly turning the valve key clockwise to decrease the flame or counter-clockwise to increase it.

An installed fire pit in operation, demonstrating how to use the valve key to adjust the gas flow and control the flame height.

6.3 Shutting Down

1. Turn the valve key fully clockwise to shut off the gas flow to the burner.
2. Close the valve on the propane tank.
3. Allow the fire pit to cool completely before covering or storing.

6.4 Operational Videos

7. Maintenance

Regular maintenance ensures the longevity and safe operation of your fire pit kit.

• Cleaning: Clean the stainless steel pan and burner periodically with a mild soap and water solution. Avoid abrasive cleaners that could scratch the surface. Ensure the unit is completely dry before use.
• Inspection: Before each use, inspect all gas connections for leaks using a soapy water solution. Bubbles indicate a leak. Tighten connections or replace parts as necessary. Check the burner holes for any obstructions.
• Storage: When not in use for extended periods, especially during harsh weather, cover the fire pit or store it in a dry, protected area.

8. Troubleshooting

If you encounter issues with your fire pit kit, refer to the common problems and solutions below:

• Problem: Fire pit does not ignite.
  Solution:
  • Check if the propane tank valve is fully open.
  • Ensure there is propane in the tank.
  • Verify that the igniter wire is securely connected to the electrode.
  • Check for gas leaks at connections using soapy water.
  • Ensure the igniter button is pressed firmly and held during ignition.
• Problem: Low flame or uneven flame.
  Solution:
  • Check for obstructions in the burner holes.
  • Ensure the gas line is not kinked.
  • Verify the propane tank regulator is functioning correctly.
  • Confirm the gas valve is fully open.
• Problem: Gas smell without flame.
  Solution:
  • Immediately shut off the gas at the tank and the control valve.
  • Evacuate the area and do not attempt to ignite.
  • Check all gas connections for leaks using soapy water. If a leak is found and cannot be resolved by tightening, replace the faulty component.
  • If the smell persists or the leak cannot be found, contact a qualified gas technician.

9. Warranty Information

Specific warranty details for the Skyflame 30 x 6 Inch Liner Fire Pit Pan Kit were not provided in the product information. Please refer to the manufacturer's official website or contact customer support for current warranty terms and conditions.

10. Customer Support

For technical assistance, replacement parts, or any questions regarding your Skyflame fire pit pan kit, please visit the Skyflame Store on Amazon or contact Skyflame customer service directly through their official channels.