SANUS Preferred Full-Motion TV Mount

Introduction

This manual provides detailed instructions for the safe and proper installation, operation, and maintenance of your SANUS Preferred SLF428-B1 Full-Motion TV Mount. Please read all instructions carefully before beginning installation. If you have any questions, contact SANUS customer support.

This mount is designed to fit most 37-inch to 90-inch flat-panel TVs weighing up to 135 lbs (61.2 kg).

Image: The SANUS Preferred SLF428-B1 Full-Motion TV Mount, showing its articulating arm and wall plate components.

Important Safety Instructions

WARNING: Failure to read and follow these instructions can result in serious personal injury, property damage, or voiding of your warranty. If you do not understand these instructions or have doubts about the safety of the installation, contact SANUS customer support or a qualified installer.

• Do not install this product on walls that are not structurally sound. Ensure the mounting surface can safely support the combined weight of the mount and the TV.
• This mount is intended for use with TVs weighing up to 135 lbs (61.2 kg). Exceeding this weight limit may result in instability and potential injury.
• Always use an assistant for lifting and positioning the TV.
• Tighten all screws firmly, but do not overtighten. Overtightening can damage screws and components.
• Ensure all cables are routed safely and do not interfere with the mount's movement.

Package Contents

Verify that all components are present and undamaged before installation. If any parts are missing or damaged, contact SANUS customer support.

• Wall Plate Assembly
• TV Bracket Set (Left and Right)
• Hardware Kit (various screws, washers, spacers for TV and wall mounting)
• Cable Management Clips
• Instruction Manual (this document)

Tools Required (Not Included)

• Stud Finder
• Pencil
• Drill with appropriate drill bits (e.g., 7/32" for wood studs, 1/2" for concrete)
• Level
• Tape Measure
• Phillips Head Screwdriver
• Socket Wrench (typically 1/2" or 13mm)

Setup and Installation

Follow these steps carefully to ensure a secure and correct installation.

Step 1: Pre-Installation Check

1. Determine Wall Type: Use a stud finder to locate the center of wood studs. For concrete or brick walls, ensure you have appropriate anchors (sold separately if not included).
2. Verify TV Compatibility: Check your TV's VESA mounting pattern and weight against the mount's specifications.
3. Choose Mounting Location: Consider viewing height, glare, and proximity to power outlets and cable access.

Step 2: Install Wall Plate

This step involves securing the main wall plate to your chosen wall location.

Image: Illustrative image showing the wall plate being mounted to a wall, with drill holes marked and screws being tightened. (Placeholder image)

1. Position the wall plate at the desired height and use a pencil to mark the pilot hole locations. Use a level to ensure it is straight.
2. Drill pilot holes at the marked locations. For wood studs, use a 7/32" (5.5 mm) drill bit. For concrete/brick, use a 1/2" (13 mm) drill bit and insert concrete anchors (if applicable).
3. Attach the wall plate to the wall using the provided lag bolts and washers. Tighten securely with a socket wrench. Do not overtighten.

Step 3: Attach TV Brackets to TV

Prepare your TV by attaching the vertical mounting brackets.

Image: Illustrative image showing the TV brackets being attached to the VESA mounting holes on the back of a television. (Placeholder image)

1. Carefully place your TV face-down on a soft, clean surface to prevent screen damage.
2. Select the correct diameter and length screws from the hardware kit that fit your TV's VESA mounting holes. Use spacers if the TV back is uneven or if cables need clearance.
3. Attach the left and right TV brackets to the back of your TV using the selected screws and washers. Ensure the brackets are centered and level. Tighten firmly with a Phillips head screwdriver.

Step 4: Mount TV to Wall Plate

With assistance, lift and secure the TV onto the wall plate.

Image: Illustrative image showing two people carefully lifting a television and hooking its attached brackets onto the wall plate. (Placeholder image)

1. With an assistant, carefully lift the TV and hook the TV brackets onto the wall plate. Ensure the brackets are fully seated on the wall plate's arms.
2. Locate the safety screws or locking mechanisms on the bottom of the TV brackets. Tighten these to secure the TV to the mount and prevent accidental dislodging.

Step 5: Cable Management

Organize and conceal cables for a clean appearance and safe operation.

Image: Illustrative image showing cables being routed through the integrated cable channels or secured with clips along the mount's articulating arm. (Placeholder image)

1. Route all necessary cables (power, HDMI, etc.) through the integrated cable channels on the mount's arm or use the provided cable management clips.
2. Ensure cables have enough slack to allow for full range of motion of the TV without being stretched or pinched.

Operating the Mount

The SANUS Preferred SLF428-B1 mount offers various adjustments for optimal viewing.

• Extend/Retract: Gently pull or push the TV to extend or retract the articulating arm. The mount extends up to 28 inches (71.1 cm) from the wall.
• Swivel: Pivot the TV left or right to achieve your desired viewing angle.
• Tilt: Loosen the tilt adjustment knobs (if present, refer to specific mount design) on the TV brackets, adjust the TV to the desired vertical angle, and then retighten the knobs to secure. The mount allows for tilting to reduce glare.
• Level Adjustment: Some mounts allow for post-installation leveling. If your TV appears slightly unlevel, consult the specific instructions for minor rotational adjustments.

Maintenance

Regular maintenance ensures the longevity and safe operation of your TV mount.

• Periodic Checks: Every few months, check all mounting screws and bolts to ensure they remain tight. Retighten if necessary, but do not overtighten.
• Cleaning: Dust the mount with a soft, dry cloth. Avoid using abrasive cleaners or solvents that could damage the finish.
• Lubrication: The mount's moving parts are designed for smooth operation and typically do not require lubrication. If movement becomes stiff, contact SANUS customer support.

Troubleshooting

• TV is not level:
  - Ensure the wall plate was installed level. If not, minor adjustments may be possible with the TV brackets (refer to specific bracket design).
  - Check if the TV brackets are securely tightened to the TV and the mount.
• Mount feels loose or unstable:
  - Immediately remove the TV from the mount.
  - Recheck all wall mounting bolts and TV bracket screws for tightness. Ensure they are properly seated in the wall studs or anchors.
  - Verify that the wall structure is sound and can support the weight.
• Difficulty adjusting the TV (tilt, swivel, extension):
  - Ensure no cables are snagged or preventing movement.
  - Check for any overtightened bolts that might restrict movement. Some joints may have adjustable tension screws.

Specifications

Warranty and Customer Support

For warranty information or technical assistance, please contact SANUS customer support. Details regarding specific warranty periods and terms can typically be found on the official SANUS website or included warranty card.

SANUS Customer Support: Visit www.sanus.com/support for contact information, FAQs, and additional resources.

Official Product Videos

No official seller videos were found for this product in the provided data. Please refer to the written instructions and diagrams for installation and operation guidance.