Introduction
This manual provides instructions for the installation, operation, and maintenance of the Criditpid 80604 Igniter. This igniter is designed as a replacement part for various pellet stove models. Please read these instructions carefully before attempting any installation or maintenance.
Compatibility
The Criditpid 80604 Igniter is compatible with the following pellet stove models:
- Vogelzang Pellet Stoves: VG5770, VG5790
- US Stove & USSC Pellet Stoves: Bay Front 5660, 5660E, 5560, 5660
- Ashley Pellet Stoves: AP5660, AP5660L, AP5660PE, AP5710, AP5770, AP5790
- Hudson River Pellet Stoves: Saranac, West Point
Specifications
The Criditpid 80604 Igniter features the following technical specifications:
Image: Criditpid 80604 Igniter showing its physical dimensions and wire length.
| Specification | Value |
|---|---|
| Volts | 120 V |
| Watts | 300W |
| Length | 6 1/4 inches |
| Width | 3/8 inches |
| Wire Length | 21 inches with 1/4 inch Male Terminal |
Image: Detailed view of the igniter's construction, highlighting the 310 Stainless Steel material, high-temperature wire, and terminal connectors.
The igniter is constructed with 310 Stainless Steel and features fiberglass-insulated high-temperature wire over stranded Grade "A" nickel wire. Heat shrink is used on solder joints for protection.
Setup and Installation
Safety First: Before attempting any installation, ensure your pellet stove is completely turned off, unplugged from its power source, and has cooled down. Failure to do so can result in electric shock or burns.
- Access the Igniter: Refer to your specific pellet stove's owner's manual for instructions on how to safely access the igniter assembly. This typically involves removing panels or covers.
- Disconnect Wiring: Carefully disconnect the existing igniter's wiring from the stove's electrical system. Note the orientation and connection points for reassembly.
- Remove Old Igniter: Unfasten and remove the old igniter from its housing.
- Install New Igniter: Insert the Criditpid 80604 Igniter into the igniter housing. Ensure it is securely fastened according to your stove's specifications.
- Connect Wiring: Connect the 1/4 inch male terminals of the new igniter to the corresponding female terminals in your stove's wiring. Ensure connections are secure.
- Reassemble Stove: Replace any panels or covers that were removed to access the igniter.
- Test Operation: Plug the stove back into its power source and follow your stove's normal startup procedure to verify the new igniter functions correctly.
If you are unsure about any step, it is recommended to consult a qualified technician or your stove's manufacturer for assistance.
Operating Principles
The igniter is a critical component in your pellet stove's automatic ignition system. When the stove is commanded to start, the igniter heats up to a high temperature, igniting the pellets in the burn pot. Once ignition is confirmed, the igniter typically deactivates, and the stove continues to burn pellets as fed by the auger system.
Maintenance
To ensure optimal performance and longevity of your igniter and pellet stove:
- Regular Cleaning: Periodically inspect the igniter and its surrounding area for ash and creosote buildup. Clean gently with a soft brush or vacuum as needed, ensuring the stove is cool and unplugged.
- Avoid Physical Damage: Be careful not to strike or bend the igniter during cleaning or other maintenance activities, as this can cause internal damage.
- Inspect Wiring: Check the igniter's wiring and terminals for any signs of wear, fraying, or loose connections during routine stove maintenance.
Troubleshooting
If your pellet stove fails to ignite, the igniter may be a contributing factor. Consider the following troubleshooting steps:
- No Heat from Igniter: If the igniter does not glow or produce heat during the startup cycle, check its electrical connections. Ensure it is receiving power. A multimeter can be used to test for continuity if you are familiar with electrical testing.
- Slow Ignition: If the stove takes an unusually long time to ignite, the igniter may be weakening. While it might still function, its efficiency could be reduced.
- Repeated Failure: If the igniter fails shortly after replacement, ensure proper installation and check for any underlying issues with the stove's control board or power supply that might be damaging the igniter.
Always consult your pellet stove's specific troubleshooting guide for more detailed diagnostics.
Warranty and Support
The Criditpid 80604 Igniter comes with a 1-year warranty from the date of purchase. This warranty covers manufacturing defects. For warranty claims or technical support, please contact Criditpid customer service through the retailer where the product was purchased.
Image: Criditpid 80604 Igniter highlighting the 1-year warranty.
