TechCare Massager Plus 24 Electronic Pulse Massager User Manual
Model: Plus 24
Introduction
The TechCare Massager Plus 24 is a rechargeable electronic pulse massager designed for temporary relief of pain associated with sore and aching muscles. It is suitable for use on the shoulder, waist, back, upper extremities, and lower extremities, often due to strain from exercise or normal household work activities.
Image: The TechCare Massager Plus 24 device, shown with various electrode pads and accessories.
Key Features
- 24 Massage Modes: Includes stimulation options such as Tapping, Acupuncture, Deep Tissue, Foot, Cupping, and Combo.
- Adjustable Timer: Set treatment duration from 10 to 60 minutes using the "T" button.
- Rechargeable Battery: Features an internal lithium battery providing up to 20 hours of continuous use.
- Dual Output (A-B): Allows for simultaneous use by two separate users or on two different body areas.
- Large LCD Screen: Provides an easy-to-read interface, enhancing usability for all users.
Image: Visual representation of the 24 available massage modes.
Setup Guide
- Charge the Device: Before first use, fully charge the internal lithium battery using the provided USB cable and AC wall plug.
- Attach Electrode Pads: Snap the electrode pads onto the pad cables. Ensure the device is turned OFF before connecting the cables.
- Apply Pads to Skin: Place the electrode pads firmly on clean, dry skin in the desired treatment area. Refer to the included pad placement guide for optimal positioning.
- Turn On Device: Locate the ON/OFF switch on the side of the device and slide it to the 'ON' position.
- Select Mode: Use the 'M' button to cycle through the 24 available massage modes.
- Adjust Intensity: Use the '+' and '-' buttons to increase or decrease the intensity level until a comfortable sensation is achieved.
- Set Timer: Press the 'T' button to adjust the treatment duration (10-60 minutes).
Image: Step-by-step visual guide for setting up and using the TechCare Massager Plus 24.
Operating Instructions
Power On/Off
To turn the device on, slide the power switch located on the side of the unit to the 'ON' position. The LCD screen will illuminate. To turn off, slide the switch back to the 'OFF' position.
Mode Selection
Press the 'M' button to cycle through the 24 pre-programmed massage modes. Each press will advance to the next mode. The selected mode will be displayed on the LCD screen.
Intensity Adjustment
Use the '+' button to increase the intensity of the pulse and the '-' button to decrease it. Adjust the intensity gradually until you feel a comfortable, stimulating sensation. Avoid setting the intensity too high, which may cause discomfort.
Timer Setting
The device has an adjustable timer. Press the 'T' button to select the desired treatment duration, ranging from 10 to 60 minutes. The remaining time will be displayed on the screen.
Dual Channel Operation (A-B Output)
The A-B output feature allows for two sets of electrode pads to be used simultaneously, either on different body parts or by two individuals. Each channel (A and B) can have its intensity adjusted independently.
Image: The device's display showing various massage modes and intensity levels.
Maintenance
- Cleaning the Device: Wipe the device with a soft, damp cloth. Do not use abrasive cleaners or immerse the device in water.
- Electrode Pad Care: After each use, place the electrode pads back onto their protective film to maintain their adhesive quality. Store them in a cool, dry place. Replace pads when they lose their stickiness.
- Charging: Recharge the device when the battery indicator shows low power. Avoid overcharging for extended periods.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No sensation or weak pulse | Pads not properly attached; low battery; intensity too low; faulty cable. | Ensure pads are firmly on skin; recharge device; increase intensity; check cable connections or replace if damaged. |
| Device does not turn on | Battery is completely drained; power switch is off. | Charge the device for at least 30 minutes; ensure power switch is in the 'ON' position. |
| Pads losing stickiness | Pads are dirty or worn out. | Clean skin before application; gently wipe pads with a damp cloth (do not soak); replace pads if stickiness is not restored. |
Specifications
- Model: Plus 24
- Power Source: 1 Lithium Ion battery (included)
- Dimensions: 5.67 x 3.54 x 3.11 inches
- Weight: 1.04 Pounds
- Manufacturer: TechCare Massager
- ASIN: B0CGCFW8QB
Warranty & Support
The TechCare Massager Plus 24 comes with a limited lifetime warranty. To activate your warranty, please visit www.techcaremassager.com/pluswarranty.
For any questions or concerns, you may contact TechCare Massager directly:
- Email: wecare@techcaremassager.com
- Toll Free Number: (888) 489-6116
Statements regarding dietary supplements have not been evaluated by the FDA and are not intended to diagnose, treat, cure, or prevent any disease or health condition.