REOLINK RLA-POECS1 PoE Combiner & Splitter User Manual

1. Introduction

The REOLINK RLA-POECS1 PoE Combiner & Splitter is designed to simplify the installation of Power over Ethernet (PoE) cameras by allowing two cameras to share a single Ethernet cable run. This solution is ideal for expanding existing surveillance systems or installing multiple cameras efficiently, reducing the need for additional wiring. The RLA-POECS1 features a waterproof design, making it suitable for both indoor and outdoor applications, and offers a plug-and-play setup for ease of use.

2. What's Included

The RLA-POECS1 package contains the following components:

• PoE Combiner x1
• PoE Splitter x1
• Waterproof Lid x3
• Installation Guide x1

This image displays the items included in the package: one PoE Combiner, one PoE Splitter, three waterproof lids, and an installation guide.

3. Setup Instructions

Follow these steps to set up your REOLINK RLA-POECS1 PoE Combiner & Splitter:

1. Connect the PoE Combiner: Connect the two RJ45 male connectors of the PoE Combiner to two available PoE ports on your PoE switch or Network Video Recorder (NVR).
2. Run a Single Ethernet Cable: Connect a single Ethernet cable (not included) from the female connector of the PoE Combiner to the installation location of your cameras. This cable can support lengths up to 300ft.
3. Connect the PoE Splitter: At the camera location, connect the single Ethernet cable from the Combiner to the female connector of the PoE Splitter.
4. Connect Cameras: Attach your two PoE cameras to the two RJ45 female connectors of the PoE Splitter using separate Ethernet cables (not included).
5. Secure Waterproof Lids: For outdoor installations, ensure the waterproof lids are securely fastened over all exposed RJ45 connections to protect against environmental elements.

Compatibility Note:

• The RLA-POECS1 is designed to seamlessly integrate with most Reolink PoE cameras, excluding models RLC-823A, RLC-823A 16x, RLC-823S1, P840, and RLC-823S2.
• For NVRs, only hardware versions N5MB01, N6MB01, and N7MB01 are supported.
• Ensure your routers/cameras are compatible with precise 802.3af/at/bt standards.

A visual guide showing how to connect the PoE Combiner to a Reolink PoE NVR, then a single Ethernet cable to the PoE Splitter, which then connects to two IP cameras.

This diagram contrasts a traditional setup requiring multiple cables from an NVR to cameras with a simplified setup using the Combiner and Splitter to reduce cabling.

4. Operating Instructions

The REOLINK RLA-POECS1 is a passive device designed for plug-and-play operation. Once correctly installed, it functions automatically to transmit power and data to two PoE cameras over a single Ethernet cable. No additional configuration or software is required for its operation.

The primary benefit of this device is to extend your surveillance system's reach and simplify wiring, allowing for efficient camera placement without extensive new cable runs.

An image showing the REOLINK RLA-POECS1 PoE Combiner and Splitter units, highlighting their compact design.

5. Maintenance

The RLA-POECS1 requires minimal maintenance. To ensure optimal performance and longevity:

• Waterproof Lids: Regularly inspect the waterproof lids, especially in outdoor installations, to ensure they are securely sealed and free from damage. This prevents moisture ingress.
• Cable Inspection: Periodically check the connected Ethernet cables for any signs of wear, damage, or loose connections.
• Cleaning: If necessary, gently wipe the units with a dry, soft cloth to remove dust or dirt. Avoid using harsh chemicals or abrasive materials.

A detailed view of the waterproof lid being secured on the RLA-POECS1 connector, demonstrating its suitability for outdoor environments.

An image showing the RLA-POECS1 unit installed on an exterior wall during rainfall, emphasizing its waterproof design for outdoor applications.

6. Troubleshooting

If you encounter issues with your RLA-POECS1, consider the following troubleshooting steps:

• Only One Camera Powers On: Ensure both RJ45 male connectors of the Combiner are securely plugged into active PoE ports on your NVR or switch. Verify that both cameras are compatible with the RLA-POECS1 and are properly connected to the Splitter.
• No Signal/Power to Cameras:
  • Check all cable connections for tightness and proper seating.
  • Verify that the Ethernet cable connecting the Combiner and Splitter is not damaged and is within the recommended length (up to 300ft). Excessive cable length can lead to signal degradation.
  • Confirm that your PoE switch or NVR provides sufficient power according to 802.3af/at/bt standards for both cameras.
  • Ensure your cameras are compatible with the RLA-POECS1 (refer to the compatibility list in Section 3).
• Intermittent Connection: This could be due to a faulty Ethernet cable, loose connections, or environmental interference. Inspect all components and connections.

7. Specifications

Graphic indicating a reach of up to 300 feet for the PoE Combiner and Splitter.

8. Warranty and Support

The REOLINK RLA-POECS1 PoE Combiner & Splitter is backed by a 2-year warranty. This warranty covers defects in materials and workmanship under normal use.

For technical support, warranty claims, or further assistance, please visit the official REOLINK website or contact their customer service directly. Ensure you have your product model number (RLA-POECS1) and proof of purchase available when seeking support.