Introduction
Welcome to the instruction manual for your Transformers Studio Series Voyager Bumblebee 110 Shockwave action figure. This figure is designed for collectors and enthusiasts aged 8 and up, offering intricate detail and multiple modes of play. Shockwave, a formidable Decepticon, can convert between his robot form and a Cybertronian tank. This manual provides essential information for assembly, operation, and care of your figure.
Safety Information
Warning: Choking Hazard – Small parts may be generated. Not for children under 3 years.
Please keep all packaging materials away from children. Inspect the figure regularly for any loose or damaged parts. Do not attempt to force transformation steps if resistance is met, as this may cause damage to the figure.
What's in the Box
- Transformers Studio Series Voyager Bumblebee 110 Shockwave Figure
- 2-piece Cannon Accessory
- Removable Backdrop
- Instructions (this manual)
Figure packaging, displaying the product and its key features.
Setup
Your Transformers Shockwave figure comes pre-assembled in robot mode. No initial assembly is required beyond removing it from the packaging.
Attaching the Cannon Accessory
- Locate the two pieces of the cannon accessory.
- Align the connection points and firmly press the two pieces together until they click into place, forming a single cannon.
- Attach the assembled cannon to Shockwave's left arm by aligning the peg on the cannon with the port on the figure's arm. Ensure a secure fit.
Shockwave figure with its signature cannon accessory attached to the arm.
Using the Removable Backdrop
The included backdrop can be used to display your Shockwave figure in the Cybertron Falls scene, enhancing its visual appeal for display purposes.
- Carefully remove the backdrop from its packaging.
- Unfold the backdrop and place it behind the figure to recreate the iconic scene.
The back of the packaging illustrates the figure's two modes and the included backdrop.
Operating the Figure (Transformation)
The Transformers Studio Series 110 Shockwave figure converts between robot and Cybertronian tank modes in 22 steps. Follow these general guidelines for transformation. Refer to the detailed instructions included in the box for specific step-by-step visuals.
Robot Mode to Cybertronian Tank Mode
Shockwave in Robot Mode.
- Begin with the figure in robot mode.
- Carefully detach the cannon accessory from the arm if it is attached.
- Manipulate the arms and legs, folding and rotating them according to the included visual instructions to form the tank's chassis.
- Fold the head and torso components to conceal them within the tank's structure.
- Reattach the cannon accessory to the designated port on the tank mode, typically on the top.
- Ensure all panels and tabs are securely locked into place for a stable tank mode.
Shockwave in Cybertronian Tank Mode.
Cybertronian Tank Mode to Robot Mode
To convert back to robot mode, reverse the steps outlined above. Pay close attention to the locking mechanisms and panel alignments to ensure a smooth transformation.
Note: Some steps may require gentle force. If a part does not move easily, re-check the previous steps to ensure correct alignment. Do not apply excessive force.
Maintenance
- Cleaning: Wipe the figure with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners, as these may damage the paint or plastic.
- Storage: Store the figure in a cool, dry place away from direct sunlight to prevent discoloration or material degradation.
- Joint Care: If joints become stiff, gently work them back and forth. Avoid applying lubricants, as they may attract dust or damage the plastic.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Figure parts not aligning during transformation. | Incorrect previous step or misaligned tab/slot. | Review the transformation steps carefully. Ensure all tabs are aligned with their corresponding slots before applying pressure. |
| Joints are too loose or too stiff. | Normal wear and tear or manufacturing variation. | For loose joints, a small amount of clear nail polish or super glue applied to the joint and allowed to dry can add friction. For stiff joints, gently work them back and forth. Do not force. |
| Accessory does not fit securely. | Incorrect orientation or debris in the port. | Ensure the accessory is oriented correctly. Check the port and peg for any obstructions and clear them if necessary. |
Specifications
| Feature | Detail |
|---|---|
| Product Dimensions | 3.15 x 6.3 x 9.06 inches |
| Item Weight | 12.3 ounces |
| Item Model Number | F8767 |
| Manufacturer Recommended Age | 8 years and up |
| Release Date | April 12, 2024 |
| Language | English |
| Manufacturer | Hasbro |
Official Product Videos
The following video provides an overview of the Transformers Studio Series Voyager Bumblebee 110 Shockwave figure, showcasing its features and transformation.
No official seller videos are available for this product at this time.
Warranty and Support
For information regarding product warranty, returns, or technical support, please refer to the manufacturer's official website or contact their customer service department. Keep your proof of purchase for any warranty claims.
Manufacturer: Hasbro
For further assistance, please visit the Transformers Store on Amazon.
