1. Introduction
Thank you for choosing Ansell HYFLEX 78-403 Mechanical Protection Gloves. These gloves are designed to provide reliable hand protection for various mechanical tasks, offering a balance of comfort, breathability, and durability. This manual provides essential information for the proper use, care, and maintenance of your gloves to ensure optimal performance and longevity.
2. Safety Information
Always read and understand all safety information before using the gloves.
- Intended Use: These gloves are intended for mechanical protection. Do not use them for protection against chemical hazards, extreme heat, or electrical risks unless specifically certified for such applications.
- Inspection: Before each use, inspect gloves for any signs of damage, tears, punctures, or excessive wear. Damaged gloves may not provide adequate protection and should be replaced immediately.
- Fit: Ensure gloves fit properly. Ill-fitting gloves can impair dexterity and reduce protection.
- Allergies: If you have known allergies to materials such as Nitrile, consult a medical professional before using these gloves. Discontinue use if irritation or allergic reaction occurs.
- Disposal: Dispose of used or damaged gloves according to local regulations.
3. Product Overview
The HYFLEX 78-403 gloves are designed for comfort and protection in various work environments.
Figure 3.1: Front view of a pair of HYFLEX 78-403 gloves, showing the white knit material and ribbed cuff.
Figure 3.2: Close-up view of a single HYFLEX 78-403 glove on a hand, highlighting the fit and material texture.
Key Features:
- Extended Wrist: Designed to better cover the forearm, ensuring continuity of protection with garments.
- Breathability: Offers good breathability for enhanced comfort during prolonged use.
- Low Lint Properties: Helps protect products from cotton-lint and hand contamination, making them suitable for sensitive applications.
- Material: Constructed with durable Nitrile material for reliable mechanical protection.
4. Setup
The HYFLEX 78-403 gloves require minimal setup before use.
- Unpack: Remove gloves from their packaging.
- Inspect: Before first use, and prior to each subsequent use, visually inspect both gloves for any signs of damage, such as tears, holes, or worn areas. Do not use damaged gloves.
- Ensure Cleanliness: Ensure your hands are clean and dry before putting on the gloves to maintain hygiene and glove integrity.
5. Operating Instructions
Follow these steps for proper use of your HYFLEX 78-403 gloves.
- Donning the Gloves:
- Carefully slide your hand into the glove, ensuring your fingers are fully seated in the finger stalls.
- Adjust the glove to ensure a snug and comfortable fit, with the extended cuff covering your wrist and lower forearm.
- During Use:
- Perform tasks requiring mechanical protection, such as handling materials, assembly work, or light maintenance.
- The breathable design and low lint properties make these gloves suitable for tasks where comfort and product integrity are important.
Figure 5.1: Example of HYFLEX 78-403 gloves in use, demonstrating dexterity and protection.
- Doffing the Gloves:
- To remove, grasp the cuff of one glove and pull it off, turning it inside out.
- Hold the removed glove in the gloved hand, then insert a finger under the cuff of the remaining glove and pull it off, enclosing the first glove inside.
- Dispose of or prepare for cleaning as per the Maintenance section.
6. Maintenance
Proper care and maintenance will extend the life of your HYFLEX 78-403 gloves.
Cleaning:
- For light soiling, wipe the gloves with a damp cloth.
- For more thorough cleaning, hand wash with mild soap and cool water. Avoid harsh detergents or bleach.
- Rinse thoroughly to remove all soap residue.
- Air dry completely before storing. Do not tumble dry or expose to direct heat, as this can damage the material.
Storage:
- Store gloves in a cool, dry place away from direct sunlight, extreme temperatures, and chemicals.
- Keep them away from sharp objects that could puncture or tear the material.
7. Troubleshooting
This section addresses common issues you might encounter with your gloves.
| Problem | Possible Cause | Solution |
|---|---|---|
| Gloves feel uncomfortable or too tight/loose. | Incorrect size. | Ensure you are using the correct size for your hands. Refer to sizing guides if available. |
| Gloves show signs of wear quickly. | Excessive abrasion or improper use for the task. | Ensure gloves are suitable for the specific task's abrasion level. Replace gloves when signs of wear appear. |
| Skin irritation after wearing gloves. | Allergic reaction to material (Nitrile) or unwashed hands. | Wash hands thoroughly before and after use. If irritation persists, discontinue use and consult a medical professional. Consider alternative glove materials. |
8. Specifications
| Attribute | Detail |
|---|---|
| Model Number | 78-403 |
| Brand | Ansell |
| Generic Name | HyFlex 78-403 Mechanical Protection Gloves |
| Material | Nitrile |
| Color | White |
| Size | Size 8,0 (as per product details) |
| Special Feature | Breathable |
| Included Components | Gloves |
| Department | Unisex |
9. Warranty and Support
Specific warranty information for the HYFLEX 78-403 Mechanical Protection Gloves is not provided in the product details. For warranty claims, technical support, or further inquiries, please contact Ansell customer service directly or visit their official website.
You can often find contact information on the product packaging or through the manufacturer's official channels.
Ansell Official Website: www.ansell.com (This is a general link, specific support pages may vary by region.)
