Sena 10S Motorcycle Bluetooth Headset Communication System User Manual

1. Product Overview

The Sena 10S Bluetooth motorcycle headset and intercom system kit is designed to facilitate seamless communication among riders. It supports full duplex, dual pairing for clear and natural conversations.

Key Features:

• Bluetooth 4.1 and Universal Intercom for broad compatibility.
• Crystal-clear HD audio with Advanced Noise Control for superior sound quality.
• Intercom communication range of up to 1.6 km (1.0 mi) in open terrain.
• Supports up to 4 riders for group communication.
• Smartphone pairing for music, GPS navigation, and phone calls.
• Talk time of 12 hours on a single charge.

Figure 1.1: Front view of the Sena 10S Motorcycle Bluetooth Headset.

2. Package Contents

The Sena 10S Communication System package typically includes the following items:

• Sena 10S Headset Unit(s)
• Speaker Set
• Boom Microphone
• Wired Microphone
• Mounting Clamp Kit
• USB Power & Data Cable
• Audio Cable
• Velcro Pads for Speakers
• Microphone Sponges

Figure 2.1: All components included in the Sena 10S package.

3. Setup and Installation

3.1 Charging the Device

Before initial use, fully charge the Sena 10S headset. Connect the provided USB power & data cable to the headset's charging port and a USB power source. A full charge typically takes approximately 3 hours. The LED indicator will change color to indicate charging status.

Figure 3.1: Side view of the Sena 10S unit, showing the USB charging port.

3.2 Mounting on a Helmet

The Sena 10S can be mounted on most motorcycle helmets using the included clamp kit. Follow these general steps:

1. Loosen the screws on the back of the clamp unit.
2. Slide the clamp unit between the outer shell and the inner padding of your helmet, positioning it on the left side.
3. Tighten the screws to secure the clamp.
4. Attach the main headset unit to the clamp.
5. Install the speakers inside the helmet, aligning them with your ears. Use the Velcro pads if necessary.
6. Connect the microphone (boom or wired) to the headset unit and position it appropriately for clear voice pickup.

Figure 3.2: Sena 10S headset mounted on a motorcycle helmet.

4. Operating Instructions

4.1 Power On/Off

• Power On: Press and hold the Phone Button and the Jog Dial for 1 second.
• Power Off: Tap the Phone Button and the Jog Dial simultaneously.

4.2 Volume Control

Rotate the Jog Dial clockwise to increase volume and counter-clockwise to decrease volume.

4.3 Bluetooth Pairing (Smartphone)

To pair your smartphone with the Sena 10S for music, GPS, and phone calls:

1. With the headset off, press and hold the Phone Button for 5 seconds until the LED flashes red and blue alternately.
2. On your smartphone, enable Bluetooth and search for devices.
3. Select 'Sena 10S' from the list of found devices.
4. If prompted, enter '0000' for the PIN.

4.4 Intercom Communication

The Sena 10S supports intercom communication with up to 4 riders. Ensure all devices are powered on and within range.

• Pairing with another Sena headset: Press and hold the Jog Dial of both units for 5 seconds until the LEDs flash red. Tap the Jog Dial on either unit to complete pairing.
• Starting/Ending Intercom: Tap the Jog Dial once to start or end a conversation with the first paired intercom friend. Tap twice for the second, and three times for the third.

4.5 Music Streaming and Phone Calls

• Play/Pause Music: Press and hold the Jog Dial for 1 second.
• Answer/End Call: Tap the Phone Button.
• Voice Dial: Press and hold the Phone Button for 3 seconds.

5. Maintenance and Care

To ensure the longevity and optimal performance of your Sena 10S headset, follow these maintenance guidelines:

• Keep the device dry. Moisture can damage internal circuits.
• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
• Clean the microphone and speaker grilles gently with a soft, dry cloth.
• Store the device in a cool, dry place when not in use.
• Charge the battery regularly, even if not in use, to maintain battery health.

6. Troubleshooting

If you encounter issues with your Sena 10S, try the following steps:

• No Power: Ensure the battery is charged. Connect to a power source and check if the charging indicator lights up.
• No Sound/Low Volume: Check volume settings on both the headset and your connected device. Ensure speakers are correctly positioned.
• Intercom Not Connecting: Verify both units are powered on and within range. Re-attempt intercom pairing.
• Bluetooth Disconnection: Ensure your paired device is within range. Try re-pairing the device.
• Resetting the Device: If issues persist, perform a factory reset (refer to the full user manual for specific instructions on your model).

7. Technical Specifications

8. Official Product Video

9. Warranty and Support

For detailed warranty information, please refer to the warranty card included in your product packaging or visit the official Sena website. For technical support, troubleshooting assistance, or further inquiries, please contact Sena customer service through their official channels.