Introduction
This manual provides essential information for the safe and efficient operation of your Homematic IP Funk Wandtaster HmIP-WRC2-A. Please read these instructions carefully before installation and initial use. Keep this manual for future reference.
Figure 1: Front view of the Homematic IP Funk Wandtaster HmIP-WRC2-A. This wireless wall switch features a clean, modern design with two distinct button areas.
Safety Information
- Do not open the device. It contains no user-serviceable parts.
- Do not immerse the device in water or other liquids.
- Use the device only in dry and dust-free environments.
- Ensure proper battery insertion according to polarity markings.
- Keep batteries out of reach of children.
Package Contents
- Homematic IP Funk Wandtaster HmIP-WRC2-A
- Mounting plate
- Adhesive strips
- Screws and wall plugs
- Batteries (typically 2x AAA, not included in all packages)
- Instruction Manual (this document)
Setup and Installation
The Homematic IP Funk Wandtaster HmIP-WRC2-A requires a Homematic IP Access Point or a CCU3 Smart Home Central Control Unit for operation. Ensure your Homematic IP system is set up and operational before proceeding.
1. System Requirements
To operate this device, you need one of the following:
- Homematic IP Access Point with the Homematic IP smartphone app (cloud service).
- Homematic IP CCU3 Smart Home Central Control Unit.
- A compatible partner solution.
Figure 2: An example of a Homematic IP Access Point, which is required for the wall switch's functionality. The VDE Smart Home certification is also visible.
2. Battery Insertion
- Carefully open the device to access the battery compartment.
- Insert the batteries, ensuring correct polarity (+/-).
- Close the device securely.
3. Pairing with Homematic IP System
- Open the Homematic IP app or your CCU3 interface.
- Initiate the pairing process for a new device.
- Follow the on-screen instructions to put the wall switch into pairing mode (usually by pressing a system button or holding a main button for a few seconds).
- Once successfully paired, assign the device to a room and configure its functions.
Figure 3: The Homematic IP app on a smartphone, demonstrating how functions and devices can be controlled either via the physical switch or the application.
4. Mounting the Wall Switch
The wall switch offers flexible mounting options:
- Adhesive Mounting: Clean the desired surface thoroughly. Apply the provided adhesive strips to the back of the mounting plate and firmly press the plate onto the wall. Attach the wall switch to the mounting plate.
- Screw Mounting: Use the mounting plate as a template to mark drilling positions. Drill holes, insert wall plugs, and secure the mounting plate with screws. Attach the wall switch to the mounting plate.
The device is designed for integration into existing 55mm switch series from leading manufacturers such as Berker, GIRA, Merten, JUNG, and ELSO.
Figure 4: Detailed view of the wall switch, highlighting its dimensions (86 mm x 86 mm x 19 mm), the two distinct buttons, and the interchangeable frame feature for integration into standard 55mm switch series.
Operating the Device
The Homematic IP Funk Wandtaster HmIP-WRC2-A features two configurable channels, allowing you to control various Homematic IP devices and functions.
Basic Functions
- Button Press: A short press on either the upper or lower button can trigger assigned actions.
- Example Applications:
- Switching lights on or off.
- Setting heating to an energy-saving (eco) mode.
- Controlling blinds or shutters.
- Activating scenarios or routines within your Homematic IP system.
Configuration via App/CCU3
All specific functions and assignments for the two buttons are configured within the Homematic IP app or the CCU3 interface. Refer to your Homematic IP system's documentation for detailed instructions on device configuration and automation.
Figure 5: Illustrates the versatile combination possibilities with other Homematic IP devices, such as smart plugs and smart lighting, all controllable via the wall switch or the app.
Maintenance
Cleaning
Clean the device with a soft, dry, lint-free cloth. Do not use abrasive cleaners, solvents, or wet cloths, as these can damage the surface or internal components.
Battery Replacement
The device has a battery life of up to four years under typical usage. When the battery level is low, your Homematic IP system will typically notify you via the app or CCU3 interface. To replace batteries:
- Carefully remove the wall switch from its mounting plate.
- Open the battery compartment.
- Remove old batteries and dispose of them according to local regulations.
- Insert new batteries, ensuring correct polarity.
- Close the battery compartment and reattach the wall switch to its mounting plate.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device not responding | Low or depleted batteries. Device out of range of Access Point/CCU3. Not properly paired. | Replace batteries. Move device closer to Access Point/CCU3. Re-pair the device with your Homematic IP system. |
| Cannot pair device | Access Point/CCU3 not in pairing mode. Device already paired to another system. Interference. | Ensure your Homematic IP system is in pairing mode. Perform a factory reset on the wall switch (refer to Homematic IP system documentation for specific steps). Try pairing in a different location or temporarily disable other wireless devices. |
| Functions not executing correctly | Incorrect configuration in the app/CCU3. Associated device (e.g., light, heater) is offline or malfunctioning. | Check and reconfigure the button assignments in the Homematic IP app or CCU3. Verify the status and functionality of the target device. |
Specifications
| Model Number | HmIP-WRC2-A |
| Brand | Homematic IP |
| Dimensions (L x W x H) | 86 mm x 86 mm x 19 mm |
| Weight | 82 g |
| Power Supply | Battery operated (type not specified, typically AAA) |
| Battery Life | Up to 4 years (typical) |
| Operation Mode | ON-OFF |
| Current Rating | 2 Amps |
| Wattage | 3.45 watts |
| Switch Type | Wireless mural switch |
| Material | Plastic (body), Metal (contact) |
| Number of Positions | 2 |
| Color | Anthracite (also available in white) |
| Compatibility | Homematic IP Access Point, CCU3, compatible 55mm switch series (Berker, GIRA, Merten, JUNG, ELSO) |
Figure 6: The Homematic IP Funk Wandtaster is available in both anthracite (shown on left) and white (shown on right) color options.
Warranty and Support
Warranty Information
Specific warranty terms and conditions are provided by the manufacturer, Homematic IP. Please refer to the warranty card included with your product or visit the official Homematic IP website for detailed information regarding warranty coverage and duration.
Technical Support
For technical assistance, troubleshooting beyond this manual, or inquiries about your Homematic IP system, please contact Homematic IP customer support. Contact details can typically be found on the manufacturer's official website or in your Homematic IP system documentation.
Online Resources: For additional information, FAQs, and software updates, visit the official Homematic IP website.
