Introduction
This manual provides comprehensive instructions for the assembly, operation, maintenance, and troubleshooting of your GAOMON Full Size Velvet Button Tufted Bed Frame, Model SBH01DF. Please read this manual thoroughly before assembly and retain it for future reference.

Image: The GAOMON Full Size Velvet Button Tufted Bed Frame, featuring a grey velvet headboard and footboard with button tufting, supported by a gold-finished metal frame, shown in a bedroom setting.
Safety Information
- Ensure all parts are present and undamaged before beginning assembly.
- Assemble the bed frame on a soft, clean surface to prevent scratches.
- Do not overtighten screws during assembly to avoid stripping threads.
- Regularly check all connections to ensure they remain tight and secure.
- Do not exceed the maximum weight capacity of 800 lbs.
- Keep small parts away from children during assembly.
Parts List
Before assembly, verify that all components listed below are included in your package:
- A. Headboard Panel (1)
- B. Footboard Panel (1)
- C. Side Rails (2)
- D. Center Support Beam (1)
- E. Metal Slats (approx. 12-14)
- F. Support Legs (4-6, including center leg)
- G. Hardware Pack (Screws, Washers, Allen Wrench) (1)

Image: Detailed view of the bed frame's structural components, including strong support slats, sound-absorbing sponge for noise reduction, robust bed legs, and floor protection feet.
Setup and Assembly
Follow these steps for proper assembly. It is recommended to have two people for assembly.
- Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, soft surface. Identify each component using the parts list.
- Attach Side Rails to Headboard: Connect the side rails (C) to the headboard panel (A) using the provided screws and Allen wrench from the hardware pack (G). Ensure connections are secure but do not fully tighten yet.
- Attach Side Rails to Footboard: Connect the other end of the side rails (C) to the footboard panel (B). Again, secure with screws but do not fully tighten.
- Install Center Support Beam: Attach the center support beam (D) to the designated brackets on the headboard and footboard. Ensure it is centered and level.
- Place Metal Slats: Position the metal slats (E) across the side rails, ensuring they are evenly spaced and securely fastened to the frame. The design provides sufficient support without a box spring.
- Install Support Legs: Attach any additional support legs (F) to the center beam or other designated areas as per the included diagram.
- Final Tightening: Once all components are in place and aligned, systematically tighten all screws and bolts until secure. Do not overtighten.

Image: Diagram illustrating the full dimensions of the bed frame (78.3"L x 53.9"W x 46"H) and its maximum weight capacity of 800 lbs.
Operating Instructions
The GAOMON bed frame is designed for use with a mattress directly on its steel slat support system, eliminating the need for a box spring.
- Mattress Placement: Carefully place your full-size mattress onto the assembled slat system. Ensure the mattress is centered and fully supported by the frame.
- Weight Distribution: Distribute weight evenly across the bed frame. The maximum weight capacity is 800 lbs, including the mattress and occupants.
- Under-Bed Storage: The frame provides approximately 12.6 inches of clearance for under-bed storage. Utilize this space for bins or boxes as needed.

Image: The GAOMON bed frame positioned in a bedroom, showcasing its design and the available space underneath for storage baskets.

Image: View showing the under-bed clearance of 12.6 inches, suitable for storage containers, with the overall frame height of 17.7 inches from the floor to the top of the side rail.
Maintenance
- Cleaning the Frame: Wipe metal surfaces with a soft, damp cloth. Avoid abrasive cleaners.
- Cleaning the Velvet Headboard/Footboard: For light cleaning, use a soft brush or vacuum with an upholstery attachment. For spills, blot immediately with a clean, dry cloth. Do not rub. For stubborn stains, consult a professional upholstery cleaner.
- Hardware Check: Periodically (every 3-6 months) check all bolts and screws to ensure they are tight. Retighten if necessary to maintain stability and prevent noise.

Image: Close-up view of the grey velvet button-tufted headboard, highlighting the fabric texture and button details, demonstrating the quality of the upholstery.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Bed frame is squeaking or noisy. | Loose bolts or connections; uneven floor. | Check and tighten all bolts and screws. Ensure slats are properly seated. Verify the bed is on a level surface. |
| Bed frame feels unstable. | Improper assembly or loose connections. | Verify all assembly steps were followed correctly. Ensure all hardware is fully tightened. Check if the bed is on an even surface. |
| Parts are missing or damaged upon arrival. | Manufacturing defect or shipping damage. | Contact GAOMON customer support immediately for replacement parts. Provide proof of purchase and details of the issue. |
Specifications
- Model: SBH01DF
- Size: Full
- Product Dimensions (L x W x H): 78.3" x 53.9" x 46"
- Material: High-quality metal frame, Velvet upholstery
- Color: Grey
- Weight Capacity: 800 lbs
- Item Weight: 80 pounds
- Special Features: No Box Spring Needed, Squeak Resistant design
- Assembly Required: Yes
- Headboard Thickness: 1.4 inches (soft package)
- Under-Bed Clearance: 12.6 inches

Image: Close-up showing the soft package thickness of the headboard, measured at 1.4 inches, indicating comfortable padding and construction detail.
Warranty and Support
GAOMON products are manufactured with quality and durability in mind. While specific warranty terms may vary, GAOMON typically offers support for manufacturing defects. For detailed warranty information or to report missing/damaged parts, please contact GAOMON customer service.
Customer Support: For assistance, please refer to the contact information provided with your purchase or visit the official GAOMON website. Please have your model number (SBH01DF) and purchase details ready when contacting support.