1. Introduction
The Steinel GlueMatic 7011 is a professional-grade electronically controlled glue gun designed for precise and efficient hot melt gluing. It features adjustable temperature settings, a fast warm-up time, and an ergonomic design for comfortable use in various applications.
This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your GlueMatic 7011 glue gun. Please read it thoroughly before first use and keep it for future reference.
Image 1.1: The Steinel GlueMatic 7011 Glue Gun, including its carrying case, three 11mm glue sticks, and an interchangeable nozzle.
2. Safety Instructions
Always observe the following safety precautions to prevent injury or damage:
- Hot Surfaces: The nozzle and melted glue become very hot during operation. Avoid direct contact with skin to prevent burns.
- Ventilation: Use the glue gun in a well-ventilated area.
- Power Supply: Ensure the voltage matches the specifications of the glue gun (220V). Do not use with damaged cords or plugs.
- Children and Pets: Keep the appliance out of reach of children and pets.
- Flammable Materials: Do not use near flammable liquids, gases, or materials.
- Unattended Operation: Never leave the hot glue gun unattended. Always unplug it when not in use.
- Storage: Allow the glue gun to cool completely before storing.
3. Package Contents
Verify that all items are present in the package:
- Steinel GlueMatic 7011 Glue Gun
- 3x Universal 11mm Glue Sticks
- Long Nozzle (pre-installed or included separately)
- Instruction Manual (this document)
4. Setup
- Unpacking: Carefully remove all components from the packaging.
- Nozzle Attachment: Ensure the long nozzle is securely attached. Additional nozzles (sold separately) can be interchanged as needed.
- Stand Placement: Place the glue gun on a stable, heat-resistant surface using its integrated stand. The stand can be removed for reaching difficult areas, but always ensure the hot nozzle does not contact surfaces.
- Power Connection: Plug the power cord into a suitable 220V electrical outlet.
- Insert Glue Stick: Insert an 11mm glue stick into the opening at the rear of the glue gun until it stops.
Image 4.1: The GlueMatic 7011 with its removable stand, ready for use.
5. Operating Instructions
- Power On: Once plugged in, the LCD display will illuminate.
- Temperature Setting: Use the controls near the LCD display to set the desired temperature between 40°C and 230°C in 1°C increments. The display shows the current temperature and the set temperature.
- Warm-up: The glue gun will begin heating. It typically reaches operating temperature in less than 2 minutes. Wait until the set temperature is reached before applying glue.
- Applying Glue: Gently press the ergonomic feed trigger to dispense melted glue. The amount of adhesive per stroke is individually adjustable.
- Nozzle Change: To change nozzles, ensure the glue gun is unplugged and has cooled sufficiently. Unscrew the current nozzle and screw on the desired replacement. Always use Steinel approved nozzles.
- Replacing Glue Sticks: When a glue stick is nearly depleted, insert a new 11mm glue stick into the rear opening. The new stick will push the remaining portion forward.
- Power Off: Unplug the glue gun from the power outlet when finished.
Image 5.1: Key operational features including temperature display and nozzle.
Image 5.2: Ergonomic design elements for comfortable use.
The GlueMatic 7011 is compatible with various 11mm special glue sticks, each optimized for different melting points and applications. Refer to the glue stick compatibility chart for guidance on selecting the appropriate adhesive for your project.
Image 5.3: Steinel Glue Stick Compatibility Chart.
6. Maintenance
- Cleaning: Ensure the glue gun is unplugged and completely cool before cleaning. Wipe the exterior with a damp cloth. Do not use abrasive cleaners or solvents.
- Nozzle Care: Periodically check the nozzle for blockages. If glue has hardened around the nozzle, allow the gun to heat up slightly, then carefully wipe away excess glue with a heat-resistant cloth. Never attempt to clear a blockage with sharp objects while the gun is hot.
- Storage: Store the glue gun in a dry, dust-free environment, preferably in its original carrying case, once it has fully cooled.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Glue gun does not heat up. | Not plugged in; power outlet faulty; internal fault. | Check power connection; try a different outlet; contact customer support if problem persists. |
| Glue does not dispense. | Not at operating temperature; glue stick not fully inserted; nozzle blocked. | Allow gun to reach set temperature; push glue stick further; clear nozzle blockage (see Maintenance). |
| Excessive glue dripping from nozzle. | Temperature too high; incorrect glue stick type. | Lower temperature setting; ensure correct glue stick for application. |
If you encounter issues not listed here or if solutions do not resolve the problem, please contact Steinel customer support.
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | 086954 |
| Power Source | Corded Electric |
| Voltage | 220 Volts |
| Wattage | 110 Watts |
| Warm-up Time | Less than 2 minutes |
| Temperature Range | 40°C - 230°C (adjustable in 1°C increments) |
| Glue Stick Diameter | 11 mm |
| Output (max) | 35 g/min |
| Dimensions (L x W x H) | 230 x 70 x 290 mm (9.06"L x 2.76"W x 11.42"H) |
| Weight | 0.6 kg (1.32 pounds) |
| Cable Length | 4 meters |
| Compatible Material | Glass (and various other materials depending on glue stick) |
9. Warranty and Support
Steinel products are manufactured to high-quality standards. For warranty information, please refer to the documentation included with your purchase or visit the official Steinel website. In case of technical issues or questions regarding your GlueMatic 7011, please contact Steinel customer support.
For further assistance, you may visit the Steinel Store on Amazon.