1. Introduction
This manual provides essential information for the safe and efficient operation of your FLIPSKY 85165 150KV Fully Waterproof Brushless Motor. Please read this manual thoroughly before installation and use to ensure proper function and longevity of the product. This motor is designed for high-performance applications such as efoil and ejet boards, offering robust power and waterproof reliability.
2. Safety Instructions
Always observe the following safety precautions to prevent injury or damage to the motor and associated equipment:
- Ensure all electrical connections are secure and properly insulated before applying power.
- Do not exceed the specified voltage range (6-24S, 25.2-100V) or current limits (Peak 330A, Rate 165A).
- Avoid operating the motor without a load for extended periods.
- Keep hands and loose clothing away from rotating parts during operation.
- Regularly inspect the motor for any signs of damage or wear.
- This motor is waterproof (IP68), but ensure all connections are sealed appropriately for submerged use.
- In case of overheating, immediately disconnect power and allow the motor to cool down.
3. Product Overview
The FLIPSKY 85165 150KV motor is a high-performance, sensorless brushless motor designed for demanding aquatic applications. Its robust construction and IP68 waterproof rating ensure reliable operation in challenging environments. The package includes the motor itself.
Image 1: Front view of the FLIPSKY 85165 150KV Brushless Motor, showing the splined shaft and mounting points.
Image 2: Side view of the FLIPSKY 85165 150KV Brushless Motor, highlighting the motor body and output shaft.
Image 3: The FLIPSKY 85165 150KV Brushless Motor shown with a propeller attached, demonstrating a typical application setup.
4. Specifications
| Feature | Specification |
|---|---|
| Voltage Range | 6-24S (25.2-100V) |
| Max Power | 19500W |
| Rated Power | 8200W |
| Peak Current | 330A |
| Rated Current | 165A |
| Motor KV | 150KV |
| Size (OD*L) | 85mm * 165mm |
| Shaft Diameter | 12mm |
| Max Output Torque | 26 N.m |
| Rated Torque | 12.6 N.m |
| Waterproof Rating | IP68 |
| Connectors | 10mm plug |
| Structure | 12N/10P |
| Insulation Current | AC500v/1ma/3s |
| Resistance | 14.5mΩ |
| Inductance | 18.2μH |
| Three-phase Leads | 3*6AWG (8.5mm) |
| Weight | 4.7KG |
| Material | Alloy Steel |
Image 4: Rear view of the FLIPSKY 85165 150KV Brushless Motor, showing the three-phase power cables and temperature sensor wire.
Image 5: Front view of the FLIPSKY 85165 150KV Brushless Motor, detailing the mounting hole pattern around the shaft.
Image 6: Technical drawing of the FLIPSKY 85165 150KV Brushless Motor, providing detailed dimensions for installation and integration.
5. Setup and Installation
Proper installation is crucial for the motor's performance and safety. Follow these steps carefully:
- Mounting: Securely mount the motor using appropriate fasteners to a rigid structure. Ensure adequate ventilation if not fully submerged, or proper sealing if submerged. Refer to the technical drawing for mounting hole patterns and dimensions.
- Electrical Connections:
- Connect the three-phase motor leads (3*6AWG with 10mm plugs) to your Electronic Speed Controller (ESC). Ensure correct phase sequence for desired rotation direction. If the motor spins in the wrong direction, swap any two of the three phase wires.
- Connect the temperature sensor wire (if applicable) to your ESC or monitoring system.
- Ensure all connections are robust and protected from water ingress, especially for waterproof applications.
- Propeller/Load Attachment: Attach the propeller or other load to the 12mm splined shaft. Ensure it is balanced and securely fastened to prevent vibration and damage.
- ESC Configuration: Configure your ESC according to the motor's specifications (KV, pole count, voltage range) for optimal performance and protection.
6. Operating Instructions
Once installed and configured, the motor is ready for operation:
- Initial Test: Perform a low-power test run to verify correct rotation direction and smooth operation.
- Monitoring: During operation, monitor motor temperature and current draw, especially during initial runs or under new load conditions. The maximum working temperature is 180°C.
- Waterproof Operation: The IP68 rating ensures the motor can be submerged. However, ensure all external connections (ESC, battery) are also adequately protected for your specific application.
Video 1: Official product video demonstrating the FLIPSKY 85165 150KV motor, including its specifications and waterproof capabilities. This video is provided by the seller, Shenzhen Flipsky Technology Company Limited.
7. Maintenance
Regular maintenance helps prolong the life and performance of your motor:
- Cleaning: After use, especially in saltwater, rinse the motor with fresh water to remove salt and debris.
- Inspection: Periodically inspect the motor for any signs of corrosion, loose connections, or physical damage. Check the shaft for any play or unusual wear.
- Storage: Store the motor in a dry, cool place when not in use.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Motor not spinning | No power, loose connections, ESC error, motor damage. | Check battery, ESC, and all wiring. Verify ESC is properly configured. Inspect motor for physical damage. |
| Motor spins in wrong direction | Incorrect phase wire connection. | Swap any two of the three phase wires between the motor and ESC. |
| Motor overheating | Overload, insufficient cooling, incorrect ESC settings. | Reduce load, ensure proper water flow for cooling, check ESC timing and current limits. |
| Excessive vibration/noise | Unbalanced propeller/load, loose mounting, damaged bearings. | Balance propeller, tighten mounting screws, inspect bearings for wear. |
9. Warranty and Support
FLIPSKY products are manufactured to high standards. For warranty information and technical support, please refer to the official FLIPSKY website or contact your retailer. If there are any questions or you need help, feel free to contact us; we will always be here to help you out within 24 hours.
Manufacturer: FLIPSKY
Contact: www.flipsky.net
