1. Introduction
This manual provides essential information for the safe and effective use of your TASER Performance Power Magazine (PPM). The PPM is a reliable lithium energy cell designed to power TASER X1, X2, and X26P devices, ensuring optimal performance and extended readiness for self-defense. Please read this manual thoroughly before installation and operation.
Figure 1: TASER Performance Power Magazine (PPM)
2. Safety Information
Always prioritize safety when handling any TASER product. The Performance Power Magazine contains a lithium battery and requires careful handling.
- Non-Rechargeable: The PPM is a single-use, non-rechargeable battery. Do not attempt to recharge it.
- Device Compatibility: Use the PPM exclusively with compatible TASER X1, X2, and X26P devices.
- Storage: Store the PPM in a cool, dry place, away from direct sunlight and extreme temperatures.
- Disassembly: Do not disassemble, puncture, or modify the battery. This can lead to explosion, fire, or burns.
- Water Exposure: Avoid exposing the battery to water or high humidity.
- Disposal: Dispose of used PPMs according to local regulations for lithium batteries. Do not incinerate.
Figure 2: Warning label on the TASER Performance Power Magazine, indicating it contains lithium batteries and should not be disassembled, recharged, or exposed to water, fire, or high temperatures. It also states it is for use with TASER devices only.
3. Package Contents
Your TASER Performance Power Magazine package includes:
- 1 x TASER Performance Power Magazine (PPM)
4. Setup: Installing the PPM
Follow these steps to properly install the Performance Power Magazine into your compatible TASER device (X1, X2, or X26P):
- Ensure your TASER device is in the "SAFE" position and the safety switch is engaged.
- Locate the battery compartment on the bottom of your TASER device.
- If an old power magazine is present, press the release button (if applicable) and carefully remove it.
- Align the new Performance Power Magazine with the battery compartment, ensuring the contacts are correctly oriented.
- Gently push the PPM into the compartment until it clicks securely into place. Do not force it.
- Verify that the PPM is fully seated and does not wobble.
- Once installed, the device's display (if applicable) should indicate battery status.
Figure 3: Side view of the TASER Performance Power Magazine, showing its form factor for insertion into a device.
Figure 4: Another angle of the TASER Performance Power Magazine, highlighting its design for secure fit.
5. Operating Instructions
The Performance Power Magazine provides the necessary energy for your TASER device's operation. Its capacity varies by device model:
- TASER X1 and X26P: Approximately 500 five-second trigger-initiated firings.
- TASER X2: Approximately 250 five-second ARC switch-initiated firings.
The PPM does not accommodate an extra cartridge. Always ensure your device is properly loaded with a cartridge (if applicable to your model) and the safety is disengaged before use. Refer to your specific TASER device's manual for detailed operating procedures.
Video 1: "The Taser Difference | Explore the Future of Personal Safety" - This video provides an overview of TASER devices and their non-lethal capabilities, demonstrating their use in self-defense scenarios. It highlights the effectiveness and safety features of TASER products, which are powered by magazines like the PPM.
6. Maintenance
The TASER Performance Power Magazine is designed for maintenance-free operation. As a non-rechargeable unit, no charging or routine servicing is required for the battery itself. To ensure longevity and proper function:
- Keep the battery contacts clean and free of debris.
- Avoid dropping the PPM or subjecting it to severe impacts.
- Replace the PPM when your TASER device indicates a low battery or after its rated firing capacity has been reached.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| TASER device does not power on. | PPM is not fully seated or is depleted. | Ensure PPM is securely installed. Replace with a new PPM if depleted. |
| Reduced firing capacity. | PPM is nearing depletion. | Replace the PPM with a new one. |
| Device indicates error related to battery. | PPM malfunction or improper installation. | Re-install the PPM. If the error persists, replace the PPM. If the issue continues with a new PPM, contact TASER support. |
8. Specifications
- Model Name: PPM
- Brand: TASER
- Compatible Devices: TASER X1, X2, X26P
- Battery Type: Lithium Energy Cell (Non-Rechargeable)
- Estimated Firings (X1/X26P): Approximately 500 five-second firings
- Estimated Firings (X2): Approximately 250 five-second ARC switch-initiated firings
- Item Weight: 2.39 ounces
- Package Dimensions: 3.54 x 2.36 x 1.26 inches
- Manufacturer: Axon Enterprise, Inc.
- UPC: 796430220100
9. Warranty and Support
For warranty information, technical support, or to purchase replacement Performance Power Magazines, please visit the official TASER website or contact Axon Enterprise, Inc. customer service. Keep your purchase receipt for warranty claims.
Manufacturer: Axon Enterprise, Inc.
Website: www.axon.com (or relevant TASER product support page)
