HOMMPA LED Nightstand User Manual

Introduction

This manual provides instructions for the assembly, operation, and maintenance of your HOMMPA LED Nightstand. Please read thoroughly before use to ensure proper setup and safe operation.

Safety Information

• Ensure all parts are securely fastened during assembly.
• Do not exceed the maximum weight recommendation of 50 pounds (22.6 kg) on the nightstand.
• Keep electrical components (LED lights, power cable) away from water and moisture.
• Supervise children around the nightstand, especially with drawers and electrical parts.
• Follow all instructions and use the table safely.
• Periodically check all connections and fasteners to ensure they remain tight.

Package Contents

Before beginning assembly, verify that all components listed below are present and undamaged. If any parts are missing or damaged, please contact customer support.

Image: All components of the HOMMPA LED Nightstand laid out for inspection.

The package includes various wooden panels, hardware (screws, dowels, cam locks), an LED light strip with a controller, and an assembly guide. A screwdriver is recommended for assembly (not included).

Assembly Instructions

The assembly process typically takes approximately 60 minutes. Ensure you have a screwdriver ready. For a visual guide, please refer to the official installation video provided by HOMMPA:

Follow these general steps for assembly:

1. Step 1: Prepare Side Panels. Attach the necessary hardware (cam bolts) to the designated holes on the side panels (parts I and J) as indicated in the diagram.
   

   Image: Step 1 of assembly, illustrating the attachment of cam bolts to the side panels.

2. Step 2: Attach LED Strip to Top Panel. Secure the LED light strip to the underside of the top panel (part A) using the provided screws. Ensure the cable is routed correctly.
   

   Image: Step 2 of assembly, showing the LED strip being secured to the top panel.

3. Step 3: Assemble LED Housing Sides. Connect the side pieces (parts F and G) to the top panel (part A) using dowels and cam locks, forming the housing for the LED light.
4. Step 4: Attach LED Housing Top. Secure the top piece (part H) to the assembled LED housing.
5. Step 5: Connect LED Housing to Main Frame. Attach the LED housing assembly to the main frame of the nightstand.
6. Step 6 & 7: Install Drawer Slides. Attach the drawer slides to the main side panels (parts C and D) and the drawer bottom panels (parts E and F).
7. Step 8: Assemble Main Frame. Connect the main side panels (parts C and D) to the bottom panel (part B) and the back panel (part M).
8. Step 9: Secure Back Panel. Insert the back panel (part M) into the grooves of the main frame and secure it.
9. Step 10: Attach Drawer Slides to Main Frame. Ensure the drawer slides are correctly aligned and secured to the main frame.
10. Step 11: Attach Top Section. Secure the top section (parts A and H) to the main nightstand frame.
11. Step 12: Finalize Top Panel. Ensure all connections for the top panel are secure.
12. Step 13: Attach Top Floating Shelf. Secure the floating top shelf (part A) to the main nightstand body.
13. Step 14 & 15: Assemble Drawers. Construct the two drawers (parts N, O, P, Q) by connecting the side and front/back panels.
14. Step 16: Insert Drawer Bottoms. Slide the bottom panels into the assembled drawers.
15. Step 17: Install Drawers. Carefully insert the completed drawers into the nightstand's main frame, ensuring they slide smoothly.
    

    Image: The two drawers of the nightstand, demonstrating their storage capacity.

Important: Refer to the detailed diagrams in your physical instruction manual for specific part identification and screw placement.

Operating Instructions: LED Lights

The HOMMPA LED Nightstand features smart RGB LED lighting with multiple control options.

Remote Control:

Use the included 24-key remote control to adjust the lighting.

Image: The 24-key remote control for the LED lighting system.

• Color Selection: Press the colored buttons (R, G, B, W, etc.) to select a static color.
• Brightness Adjustment: Use the brightness up/down buttons (sun icon) to increase or decrease light intensity.
• Mode Selection: Cycle through various dynamic modes (flash, strobe, fade, smooth) using the "MODE+" and "MODE-" buttons.
• Speed Adjustment: Adjust the speed of dynamic modes using the "SPEED+" and "SPEED-" buttons.
• On/Off: Use the red/green power buttons to turn the lights on or off.

App Bluetooth Control:

The LED lights also support control via a smartphone application.

1. Download the designated app (refer to the product packaging or included instructions for app name/QR code).
2. Enable Bluetooth on your smartphone.
3. Open the app and connect to the nightstand's LED light system.
4. Use the app interface to access additional features such as custom color mixing, music synchronization, and scheduled on/off times.

Image: Smartphone app interface for controlling the LED lights, showing various customization options.

Maintenance

To maintain the appearance and longevity of your nightstand:

• Cleaning: Wipe surfaces with a damp cloth. Avoid harsh chemicals or abrasive cleaners that could damage the high-gloss finish.
• Spills: Promptly wipe up any spills to prevent damage to the finish.
• Dusting: Regularly dust with a soft, dry cloth.
• Electrical Components: Ensure the LED strip and power cable are free from dust and debris. Do not attempt to repair electrical components yourself.

Troubleshooting

Specifications

Warranty and Support

For warranty information or technical support, please refer to the product packaging or contact HOMMPA customer service directly. Keep your purchase receipt for any warranty claims.