Introduction
This manual provides detailed instructions for the Bousnic Replacement Remote for Dog Training Collar 670. This remote is designed to be used with a compatible Bousnic Dog Training Collar 670 receiver (not included with this replacement remote). It offers various training modes to assist in effective dog training.
Image: Bousnic Dog Training Collar 670 Replacement Remote. This image displays the remote control unit, highlighting its display screen, mode buttons (Static, Vibra), and side controls for beep and intensity adjustment. The Bousnic brand logo is visible at the bottom.
Setup
1. Preparing the Receiver Collar (if applicable)
Before using the remote with a receiver collar, ensure the receiver is properly prepared. This involves installing the appropriate contact points based on your dog's coat length.
Video: How to prepare the receiver. This video demonstrates the process of attaching contact points and silicone caps to the receiver unit of a Bousnic dog training collar. It shows how to screw in the contact points securely and push in the silicone caps to prevent them from falling off. It also advises against installing contact points or spring sheets if shock mode is not preferred.
- Contact Points: For short or thin-haired dogs, use the provided short contact points with silicone caps.
- Spring Sheet: For long-haired or thick-haired dogs, you can use the spring sheet in conjunction with the contact points to ensure proper contact through the fur.
- Secure Installation: Screw in the contact points securely. When installing silicone caps, push them in until there's no air or space left between the metal tips and the black rubber caps to prevent them from falling off easily.
- Note: If you prefer not to use the static (shock) mode, do not install the contact points or spring sheet.
2. Pairing the Remote with the Receiver
To establish communication between your replacement remote and the receiver collar, follow these pairing steps:
Video: How to pair the remote and receiver. This video illustrates the steps to pair the Bousnic remote control with its receiver collar. It shows turning on both devices, pressing the receiver's power button three times until a beep is heard, and then pressing the remote's mode button to confirm successful pairing.
- Ensure both the remote and the receiver collar are turned on.
- On the receiver, quickly press the On/Off button 3 times in a row. You will hear a beep, indicating it's in pairing mode.
- On the remote, press the Mode button to check if they are paired successfully. The remote's display should show the correct mode and level, and the receiver should respond.
For an alternative pairing method, you can also try the following:
Video: How to pair the receiver with the remote. This video demonstrates another method for pairing the Bousnic remote and receiver. It shows turning on the receiver, then pressing and holding the Beep and Vibration buttons on the remote simultaneously until the receiver responds, indicating successful pairing.
- Ensure the receiver is turned off.
- Press and hold the power button on the receiver for 3 seconds until the light flashes alternately between red and green.
- On the remote, press and hold the Beep and Vibration buttons at the same time to pair the receiver collar.
- Once successfully paired, the receiver collar will beep 2 times and the green light will flash 3 times.
Operating the Remote
The Bousnic remote offers multiple modes and adjustable intensity levels to suit various training needs.
Training Modes:
- Beep Mode: Delivers an audible tone to get your dog's attention.
- Vibration Mode: Provides a gentle vibration as a warning or command.
- Static (Shock) Mode: Delivers a static correction. This mode has adjustable intensity levels from 1 to 16.
Adjusting Intensity Levels:
Use the rotary dial on the top of the remote to adjust the intensity level for the static (shock) mode. This allows for fine-tuning the correction to match your dog's sensitivity and training progress.
Remote Lock Feature:
The remote includes a security lock feature to prevent accidental activation of correction modes. Slide the lock switch on the side of the remote to engage or disengage the lock. This ensures that corrections are only delivered intentionally.
Dual Channel Control:
The remote is capable of controlling two separate receiver collars. Use the "1" and "2" buttons on the remote to switch between controlling different collars, which is useful for training multiple dogs simultaneously (requires additional receiver collars, not included).
Maintenance
- Charging: The remote is rechargeable. Use the provided USB cable to charge the unit. The battery life is designed to last a long time between charges.
- Water Resistance: The remote control unit is not waterproof. Keep it away from water to prevent damage. The receiver collar (not included with this remote) is typically waterproof, but this remote is not.
- Cleaning: Wipe the remote with a soft, dry cloth as needed. Avoid using harsh chemicals or abrasive materials.
Troubleshooting
No specific troubleshooting steps are provided in the product information. If you encounter issues, please ensure the remote and receiver are fully charged and properly paired. Refer to the pairing instructions in the Setup section. For further assistance, contact Bousnic customer support.
Specifications
| Feature | Detail |
|---|---|
| Brand | BOUSNIC |
| Model | 670 (Replacement Remote) |
| Item Weight | 4.2 ounces |
| Item Package Dimensions L x W x H | 7.32 x 2.83 x 1.85 inches |
| Color | Grey |
| Material | Plastic |
| Manufacturer | Bousnic |
| Date First Available | July 6, 2023 |
