1. Setup
1.1 Unboxing and Initial Preparation
Carefully remove the xTool P2 machine from its packaging. Ensure all protective materials are removed from the exterior and interior of the device.
Video: Step-by-step guide on unboxing the xTool P2 and preparing it for first use, including removing internal packaging and protective films.
1.2 Water Tank Filling
The xTool P2 requires a specific mixture of antifreeze and purified water for its cooling system, especially in colder environments. Refer to the table below for the correct composition based on your region's annual lowest temperature.
To fill the tank: Open the rear cover of the machine. Press down and rotate the cap counterclockwise to open the water tank. Use the provided funnel to pour the recommended amount of antifreeze and purified water into the tank.
Image: Instructions for filling the water tank, including a table detailing antifreeze and purified water ratios based on ambient temperature.
1.3 Smoke Exhaust Pipe Installation
Proper ventilation is crucial for safe operation. Install the smoke exhaust pipe to the designated port on the machine. Ensure the other end of the pipe is placed in the open air or connected to an appropriate air purifier system.
Image: Visual guide for attaching the smoke exhaust pipe to the xTool P2 machine.
1.4 Power Connection and Software Setup
Connect the machine to a power supply. Reset the emergency stop switch by twisting it clockwise until it pops out. Turn on the machine using the main power switch. Download and install the XCS (xTool Creative Space) software from the official xTool website. Connect your xTool P2 to your computer via USB or Wi-Fi within the XCS software.
Image: Steps for connecting the machine to power, resetting the emergency stop, and establishing a software connection.
1.5 Optical Path Calibration
For optimal performance, calibrate the optical path. Remove the sliding cover plate. Use the XCS software to move the laser module to the side, close to the button on the machine. Stick a piece of masking paper over the light outlet and press it down to form a circle. Close the lid and click "Pulse" in the software. Open the lid and observe where the laser beam passes through the masking paper. If it's not centered, adjust the grub screw on the lower right of the reflector holder using a hex key and screwdriver. Repeat the pulse test and adjustment until the laser beam passes through the center of the circle.
Image: Detailed steps for calibrating the laser's optical path to ensure precise operation.
2. Operating Instructions
2.1 Basic Engraving and Cutting
Place your material inside the machine. Use the XCS software to import your design, set the desired power, speed, and number of passes according to the material type. The xTool P2's 55W CO2 laser can cut 18mm black walnut and 20mm acrylic in one pass, and engrave at 600mm/s.
Image: Demonstrates the powerful 55W CO2 laser cutting through 20mm acrylic and 18mm wood in a single pass.
2.2 Accurate Positioning with Dual HD Cameras
The dual 16MP smart cameras provide accurate positioning, allowing you to preview your design in real-time on the material. This feature is especially useful for engraving tiny objects or utilizing material scraps efficiently.
Image: Illustrates the function of the dual HD cameras for precise placement of designs, even on small items.
2.3 Curved Surface Engraving
The xTool P2 can automatically construct 3D models of curved objects, enabling perfect engraving on non-flat surfaces. This expands creative possibilities for various curved materials.
Image: Shows the machine engraving intricate designs onto a curved wooden surface, highlighting its 3D curve engraving feature.
2.4 Automatic Passthrough for Large Materials
For extra-large materials up to 118 inches, the xTool P2 offers an automatic passthrough feature (requires Automatic Conveyor Feeder accessory). This allows for continuous engraving and cutting with precision.
Video: Demonstrates the xTool P2's automatic conveyor system processing a long piece of wood, showcasing its ability to handle extended materials.
2.5 Rotary Attachment (RA2 Pro)
The xTool P2 is compatible with the RA2 Pro rotary attachment, enabling engraving on cylindrical objects like tumblers, mugs, spheres, and rings. This accessory expands the range of engravable items.
Video: Shows the setup and use of the RA2 Pro rotary attachment for engraving on a cylindrical object, highlighting the measurement and alignment process.
2.6 Material Compatibility
The xTool P2 has ultra-high absorption efficiency on a wide range of materials. It is ideal for cutting acrylic of all colors, wood, leather, MDF, rubber, and fabric. It can also engrave on glass, ceramic, slate, coated metal, anodized aluminum, and more.
Image: A collage of various finished products made from different materials like wood, acrylic, leather, and metal, demonstrating the machine's versatility.
3. Maintenance
3.1 Antifreeze and Water Management
Regularly check the water level in the cooling system. If the temperature drops below 10°C (50℉), ensure the correct amount of antifreeze is added to prevent freezing and damage to the laser tube. Refer to the water tank filling instructions in Section 1.2 for specific ratios.
3.2 Cleaning
Keep the machine's interior clean to ensure optimal performance. The mirrors are magnetically attached for easy removal and cleaning. Regularly clean the lens and the rear exhaust fan. An improved air assist pump helps reduce smoke stains during operation.
4. Troubleshooting
4.1 Engraving/Cutting Inconsistencies
If you experience inconsistencies in engraving or cutting, especially with the conveyor system, ensure your material is perfectly flat. Warped materials can cause the laser to skip or result in uneven depth. Always use flat materials for best results.
4.2 Smoke Stains
While the xTool P2 features an improved air assist pump to minimize smoke stains, excessive residue might indicate insufficient ventilation or incorrect power/speed settings for the material. Ensure the exhaust pipe is properly installed and vented, and adjust settings as needed.
4.3 Alignment Issues
If your designs are not aligning correctly, especially with the rotary attachment, re-check the optical path calibration (Section 1.5). For rotary projects, ensure the object is securely fastened and the diameter measurement is accurate in the software.
5. Specifications
- Manufacturer: Makeblock Co.,Ltd
- Part Number: P1030386-A
- Item Weight: 121 pounds
- Product Dimensions: 25 x 10 x 39 inches
- Item Model Number: xTool P2
- Size: xTool P2
- Color: Gray
- Item Package Quantity: 1
- Batteries Included?: No
- Batteries Required?: No
- Laser Output Power: 55W (55000mW)
- Max Engraving Speed: 600mm/s
- Bed Size: 26" x 14"
- Max Engraving Height: 2.7" (71mm, 215mm with Riser Base)
- Camera: Dual 16MP Smart Cameras
6. Warranty and Support
6.1 Warranty Information
The xTool P2 comes with a 1-year warranty from the date of purchase. Please retain your proof of purchase for any warranty claims.
6.2 Customer Support
For technical assistance, troubleshooting, or any product-related inquiries, please contact xTool customer support. You can typically find support contact information on the official xTool website or through your purchase platform.
