Introduction
Thank you for choosing the Momcozy S12 Pro Hands-Free Wearable Breast Pump. This manual provides essential information for the safe and effective use of your breast pump. Please read it thoroughly before first use and retain for future reference.
The Momcozy S12 Pro is designed for comfort and mobility, featuring a DoubleFit Flange, three pumping modes, and nine adjustable levels to support your breastfeeding journey.
Important Safety Information
- Always read and follow all instructions before use.
- Keep the pump motor and electrical components dry. Do not submerge in water.
- Ensure all parts are correctly assembled to prevent leaks and maintain suction.
- Use only original Momcozy parts and accessories.
- If you experience pain or discomfort, discontinue use and consult a healthcare professional.
- The pump will automatically shut off after 30 minutes of continuous use.
Package Contents
The Momcozy S12 Pro package typically includes the following items:
- Momcozy S12 Pro Breast Pump units (2)
- DoubleFit Flanges (2)
- Duckbill Valves (2)
- Silicone Diaphragms (2)
- USB-C Charging Cables (2)
- Travel Pouches (2)
- Breastfeeding Manual
- Nipple Measuring Tool
- Milk Storage Bags
- Cleaning Sponge
- Nursing Bra Extender Clips
Image: The Momcozy S12 Pro breast pump package contents, including two pump units and accessories.
Setup and Assembly
1. Charging the Pump
Before first use, fully charge the pump for approximately 130 minutes. A full charge provides power for 7-8 pumping sessions at a low level. The smart display indicates battery level.
Image: The Momcozy S12 Pro pump connected to a USB-C charging cable, indicating a full battery.
2. Nipple Sizing
Correct flange sizing is crucial for comfort and effective milk expression. Use the provided Nipple Measuring Tool to determine your appropriate flange size. Stimulate your nipple until it is erect, then slide it over each hole on the tool to find the diameter that fits snugly around the base.
Image: A nipple measurement card with various sizes and a chart recommending the corresponding flange or insert size.
Refer to the chart below for recommended flange or insert sizes:
| Nipple Diameter | Recommended Flange or Insert Size |
|---|---|
| 11-13mm | 15mm |
| 13-15mm | 17mm |
| 15-17mm | 19mm |
| 17-20mm | 21mm |
| 20-23mm | 24mm |
| 23-26mm | 27mm |
| 26-29mm | 30mm |
Note: Nipple elasticity can affect sizing. You may need to size down if you have elastic nipples, or size up if you have less elastic nipples. If you experience discomfort or notice a consistent decrease in output, you may need to experiment with different sizes.
3. Assembling the Pump
Ensure all parts are clean and dry before assembly. Align the silicone diaphragm and duckbill valve correctly within the breast shield. Then, attach the pump motor to the breast milk collector, ensuring a perfect fit. The DoubleFit flange design provides a double-sealed, airtight fit.
Video: Demonstrates how to correctly measure nipple size and choose the appropriate flange for the Momcozy S12 Pro pump.
Operating Instructions
1. Pumping Modes and Levels
The Momcozy S12 Pro features three pumping modes and nine adjustable suction levels to mimic natural breastfeeding patterns:
- Stimulation Mode: Short and quick suctions to help initiate milk flow.
- Expression Mode: Slow and deep suctions for efficient milk expression.
- Mixed Mode: Combines stimulation and expression for comfortable and effective emptying of the breasts.
Image: Visual representation of the three pumping modes (Stimulation, Expression, Mixed) with their respective icons and descriptions.
2. Smart Display and Controls
The smart display on the pump motor shows pumping time and battery level. Use the intuitive buttons to power on/off, switch modes, and adjust suction levels. A one-click pause function allows for effortless control of your pumping rhythm.
3. Hands-Free Usage
The wearable design allows for hands-free mobility, making it suitable for use while commuting, traveling, or engaging in daily activities. Ensure a full-coverage nursing bra is worn to form a tight seal between your breasts and the flange, and pump in an upright or slightly leaning forward position to prevent milk leakage.
Video: A short preview showcasing the Momcozy S12 Pro being used by mothers in various daily scenarios, emphasizing its hands-free convenience.
Cleaning and Sterilization
Proper cleaning and sterilization are essential for hygiene and pump longevity. Disassemble all washable parts before cleaning.
1. Disassembly
Carefully separate the pump motor from the breast milk collector. Then, detach the silicone diaphragm, duckbill valve, and flange from the collector.
2. Cleaning
- Wash all washable parts (silicone diaphragm, silicone breast shield, milk collector, duckbill valve, flange insert) in warm soapy water (40-60°C) for 3-5 minutes.
- Rinse thoroughly with clean water.
- The pump motor is not washable. Wipe it with a damp cloth if necessary.
3. Sterilization
- Boil washable parts in water (temperature not exceeding 100°C) for 3-5 minutes.
- Alternatively, use a steam sterilizer.
- It is not recommended to sterilize your breast pump accessories in a microwave, as this may shorten the life of the accessories.
Video: A step-by-step guide on how to easily clean the Momcozy S12 Pro pump components.
Video: Demonstrates the easy disassembly and cleaning process for the Momcozy S12 Pro pump.
Maintenance
Regularly inspect all pump parts for wear and tear. Replace parts as needed to maintain optimal performance and hygiene.
- Duckbill Valve: Replace every 1-3 months.
- Silicone Diaphragm: Replace every 3-6 months.
- Flange Insert: Replace every 3-6 months.
- Silicone Breast Shield: Replace every 4-6 months.
The pump is made of BPA-free, food-grade silicone, ensuring safety for both mom and baby. Always ensure the tubing is kept dry.
Troubleshooting
1. Low Suction or No Milk Expression
- Check that all pump parts are correctly assembled and securely sealed.
- Ensure the flange size is correct for your nipple.
- Verify the duckbill valve and silicone diaphragm are not damaged or worn. Replace if necessary.
- Ensure the pump battery is sufficiently charged.
2. Milk Leakage
- Ensure all parts are assembled correctly and there are no gaps.
- Wear a full-coverage nursing bra to create a tight seal between your breasts and the flange.
- Pump in an upright or slightly leaning forward position.
3. Pump Not Turning On/Off
- Ensure the battery is charged.
- The pump will automatically shut off after 30 minutes of continuous use.
Specifications
- Model: S12 Pro
- Brand: Momcozy
- Item Weight: 1.96 pounds (0.89 Kilograms)
- Package Dimensions: 11.02 x 6.85 x 4.29 inches
- Capacity: 6 oz (180ml) per pump
- Modes: 3 (Stimulation, Expression, Mixed)
- Suction Levels: 9 adjustable levels
- Battery Life: Up to 7-8 pumping sessions on a single 130-minute charge
- Material: BPA-free, food-grade silicone
- UPC: 810184050063
Warranty and Support
The Momcozy S12 Pro comes with a one-year warranty. For any questions, support, or to extend your warranty, please visit the official Momcozy website or contact customer service.
- Official Website: www.mommed.com
- Email Support: support@mommed.com
- Phone Support: 1 (888) 341-9150 (Mon-Fri, 9 AM - 12 AM, 1 PM - 6 PM PST)