FLEXISPOT Standing Desk Converter M17A-40 Instruction Manual

Introduction

Thank you for choosing the FLEXISPOT Standing Desk Converter M17A-40. This manual provides essential information for the safe and efficient use of your new workstation. This 40-inch sit-to-stand desk riser is designed to transform any desk into an ergonomic workspace, allowing for seamless transitions between sitting and standing positions. Its spacious two-tier design accommodates monitors, laptops, keyboards, and mice, promoting comfort and productivity.

Safety Information

Please read and understand all safety instructions before assembly and use. Failure to follow these instructions may result in injury or damage to the product.

• The minimum height of the desktop is 4.7 inches.
• The maximum weight recommendation for the desktop is 44 pounds.
• The maximum weight recommendation for the keyboard tray is 4.4 pounds.
• Always ensure the desk converter is stable and not overloaded.
• Keep hands and fingers clear of moving parts during height adjustment to prevent pinching or injury.
• Do not place hot liquids directly on the surface without a coaster.
• Ensure all cables are properly managed to avoid snagging or damage during height adjustments.

Setup

The FLEXISPOT Standing Desk Converter M17A-40 arrives almost fully assembled, requiring minimal setup to get started.

1. Unboxing: Carefully remove the desk converter from its packaging. Place it on a stable, flat surface where it will be used.
2. Attach Optional Keyboard Tray: The keyboard tray is designed for easy attachment. Align the tray with the designated slots on the underside of the main desktop. Slide it into place until it clicks securely. Ensure both sides are firmly latched.

Once the keyboard tray is attached, your desk converter is ready to be customized for your workspace.

Operating Instructions

The FLEXISPOT Standing Desk Converter features a powerful gas spring system for smooth and effortless height adjustments.

1. Adjusting Height: To raise or lower the desktop, locate the single lever on the right side of the unit. Squeeze the lever to release the locking mechanism.
2. Raising the Desktop: While holding the lever, gently lift the desktop to your desired standing height. Release the lever to lock it into position. The gas spring system will assist in the upward movement.
3. Lowering the Desktop: While holding the lever, gently press down on the desktop to lower it to your desired sitting height. Release the lever to lock it into position.

The 2-tier design provides ample space for your setup:

• The top tier (40'' width) can comfortably hold a monitor up to 27'' or multiple smaller monitors.
• The base tier (12.1'' depth) is designed for a standard keyboard and mouse, or a 13'' laptop, allowing for ergonomic typing and mouse use.

Maintenance

Regular maintenance ensures the longevity and smooth operation of your FLEXISPOT Standing Desk Converter.

• Cleaning: Wipe surfaces with a soft, damp cloth. Avoid abrasive cleaners or solvents that may damage the finish.
• Lubrication: Periodically check the moving parts of the gas spring system. If movement becomes stiff, apply a small amount of silicone-based lubricant to the pivot points.
• Fasteners: Occasionally check all screws and fasteners to ensure they are tight. Retighten if necessary.

Troubleshooting

If you encounter any issues with your desk converter, refer to the following common troubleshooting tips:

• Difficulty Adjusting Height: Ensure the lever is fully squeezed when attempting to adjust the height. Check for any obstructions preventing smooth movement. Verify that the weight on the desktop does not exceed the maximum capacity.
• Wobbling: Ensure the desk converter is placed on a flat, stable surface. Check that all components are securely assembled and tightened.
• Keyboard Tray Loose: Verify that the keyboard tray is correctly inserted into its slots and the locking mechanisms are engaged.

If problems persist, please contact customer support.

Specifications

Warranty and Support

The FLEXISPOT Standing Desk Converter M17A-40 comes with a Limited Warranty. For specific terms and conditions, please refer to the warranty documentation included with your product or visit the official FLEXISPOT website.

For customer support, including assistance with assembly, operation, or troubleshooting, please contact FLEXISPOT customer service. Contact information can typically be found on the product packaging or the official FLEXISPOT website.