Brinly 42" Lawn Sweeper Instruction Manual

Introduction

This manual provides detailed instructions for the assembly, operation, maintenance, and troubleshooting of your Brinly 42" Lawn Sweeper, Model LS2-42BH-G. Please read this manual thoroughly before operating the equipment to ensure safe and efficient use.

Figure 1: Brinly 42" Lawn Sweeper (Model LS2-42BH-G)

The Brinly 42" Tow-Behind Lawn Sweeper is designed to efficiently collect leaves, pine needles, grass clippings, and thatch from your lawn. Its features include high-velocity brushes, a large capacity hamper, and an easy height adjustment mechanism for optimal performance.

Safety Information

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Always observe safety precautions when operating any lawn equipment. Failure to do so may result in serious injury or property damage.

• Read and understand all instructions in this manual before assembly or operation.
• Keep children and bystanders away from the operating area.
• Wear appropriate personal protective equipment, including eye protection and sturdy footwear.
• Ensure all fasteners are tightened securely before each use.
• Do not exceed the maximum recommended towing speed of 5 mph.
• Operate on level ground whenever possible. Avoid steep slopes.
• Always disengage the power take-off (PTO) and turn off the tractor engine before performing any adjustments or maintenance.

Setup and Assembly

The Brinly 42" Lawn Sweeper features new collapsible hamper braces for easier assembly. Follow these steps for proper setup:

1. Unpack Components: Carefully remove all parts from the packaging and verify against the parts list (not provided in this manual, refer to product packaging for full list).
2. Assemble Frame: Connect the main frame components according to the diagrams provided in the original packaging. Ensure all bolts and nuts are securely fastened.
3. Attach Wheels: Securely attach the wheels to the axle.
4. Install Brushes: Position the six high-velocity brushes into their designated slots.
5. Mount Hamper: Assemble the polyweave fabric hamper and attach it to the sweeper frame. The collapsible braces simplify this process.
6. Connect Tow Bar: Attach the universal hitch pin axle to your riding lawn or garden tractor, or ZTR mower. The clevis hitch type ensures compatibility with most models.

Ensure all connections are tight before proceeding to operation.

Operating Instructions

Proper operation ensures optimal performance and longevity of your lawn sweeper.

Brush Height Adjustment

The Twist-Lock Height Adjustment secures the brush height setting in place, even when traveling over uneven terrain. Adjust the brush height based on the type and density of debris you are sweeping:

• For light debris like grass clippings, set the brushes higher.
• For heavier debris like wet leaves or pine needles, lower the brushes to ensure maximum contact.
• The indexed brush height adjustment provides continuous material pickup.

Sweeping Procedure

1. Prepare Area: Ensure the lawn is free of large obstacles that could damage the sweeper.
2. Attach Sweeper: Securely attach the sweeper to your towing vehicle using the universal hitch pin.
3. Adjust Height: Set the brush height using the Twist-Lock mechanism.
4. Begin Sweeping: Drive your tractor at a consistent speed, ideally around 3 mph for optimal sweeping. The 5-to-1 brush-to-ground ratio ensures increased brush contact for a clean sweep.
5. Empty Hamper: The large 20 cu. ft. hamper capacity allows for extended sweeping. When full, the swinging hamper with a pull cord makes unloading easy, even from the seat of your tractor.

The high brush-to-wheel ratio and easily adjustable brush-to-ground contact minimize skipping and provide maximum performance.

Maintenance

Regular maintenance will extend the life of your Brinly Lawn Sweeper.

• After Each Use:
  • Clear any debris from the brushes and housing.
  • Inspect the polyweave fabric hamper for tears or damage.
  • Check all nuts, bolts, and fasteners for tightness. Tighten as necessary.
• Seasonal Maintenance:
  • Lubricate moving parts, especially the axle and gear mechanisms, as recommended by the manufacturer (refer to original product manual for specific lubrication points).
  • Inspect brushes for wear. Replace if bristles are significantly worn down.
  • Clean the entire unit thoroughly before storing.
• Storage:

  When not in use, simply collapse the sweeper into its upright position for quick and easy storage, minimizing its storage footprint.

Troubleshooting

Specifications

• Model: LS2-42BH-G
• Brand: Brinly
• Sweep Width: 42 inches
• Hamper Capacity: 20 cu. ft.
• Brush-to-Wheel Ratio: 5:1
• Brush Diameter: 11 inches
• Number of Brushes: Six high-velocity brushes
• Primary Material: Powder Coated Steel frame
• Secondary Material: Polyweave Fabric (UV-resistant)
• Hitch Type: Clevis (Universal Hitch Pin Axle)
• Max Tow Speed: 5 mph
• Operating Speed: 3 mph (recommended)
• Product Height: 38 inches
• Product Length: 69 inches
• Product Width: 53 inches
• Color: Hammered Black
• Country of Origin: Vietnam

Warranty and Support

For warranty information or technical support, please refer to the documentation included with your purchase or visit the official Brinly website. Keep your proof of purchase for warranty claims.

Manufacturer: Brinly-Hardy Lawn and Garden Attachments