FAITHSAIL 4FT LED Wraparound Light Instruction Manual

1. Introduction

This instruction manual provides comprehensive guidance for the safe and efficient installation, operation, and maintenance of your FAITHSAIL Dimmable 4FT LED Wraparound Light. Please read this manual thoroughly before installation and retain it for future reference.

The FAITHSAIL 4FT LED Wraparound Light is designed for various indoor applications, offering adjustable color temperatures (3000K/4000K/5000K) and brightness levels (30W/40W/50W) to suit different lighting needs. Its energy-efficient design and easy installation make it suitable for kitchens, garages, workshops, and other utility areas.

2. Safety Information

WARNING: RISK OF ELECTRIC SHOCK. DISCONNECT POWER AT THE CIRCUIT BREAKER BEFORE INSTALLATION OR SERVICING.

• Ensure the main power supply is turned off before commencing any electrical work.
• All wiring connections must comply with local and national electrical codes. If you are unsure about wiring, consult a qualified electrician.
• Do not install the fixture on surfaces that are not structurally sound or cannot support its weight.
• Do not attempt to modify the fixture. Any modifications may void the warranty and create safety hazards.
• This fixture is designed for indoor use only and is not water-resistant. Avoid installation in damp or wet locations.
• Wear appropriate personal protective equipment (PPE) such as safety glasses and gloves during installation.

3. Package Contents

Verify that all components are present and undamaged before beginning installation.

• LED Wraparound Light Fixture (2 units)
• Installation Hardware (screws, wire nuts, etc.)
• Instruction Manual

Note: "Light kit included" refers to the complete fixture and necessary mounting accessories.

4. Specifications

5. Setup and Installation

The FAITHSAIL LED Wraparound Light is designed for easy flush mount installation. Follow these steps carefully.

5.1 Pre-Installation

1. Turn off Power: Locate the circuit breaker controlling the area where the light will be installed and turn off the power. Verify power is off using a voltage tester.
2. Unpack: Carefully remove the fixture from its packaging and inspect for any damage.
3. Prepare Mounting Surface: Ensure the ceiling or wall surface is clean, dry, and capable of supporting the fixture's weight.

5.2 Wiring and Mounting

1. Remove Diffuser: Gently remove the acrylic prismatic lens (diffuser) from the fixture to access the internal components.
2. Connect Wiring:
   • Connect the black wire from the fixture to the live (black) wire from the junction box.
   • Connect the white wire from the fixture to the neutral (white) wire from the junction box.
   • Connect the green or bare copper ground wire from the fixture to the ground wire from the junction box.
   • Secure all connections with wire nuts and electrical tape.
3. Mount Fixture: Align the fixture with the junction box and secure it to the ceiling using the provided mounting screws. Ensure the fixture is firmly attached.
4. Replace Diffuser: Carefully reattach the acrylic prismatic lens (diffuser) to the fixture.

Note: For in-line assembly of multiple fixtures, knock out the designated holes at the ends of the fixtures as per local electrical codes and manufacturer guidelines.

6. Operating Instructions

Your FAITHSAIL LED Wraparound Light offers adjustable color temperature and wattage settings.

6.1 Adjusting Color Temperature (CCT)

The color temperature can be adjusted using a switch located on the fixture. This switch allows you to select between three options:

• 3000K: Warm White, suitable for a cozy and inviting atmosphere.
• 4000K: Neutral White, ideal for general tasks and balanced lighting.
• 5000K: Daylight, providing bright, crisp light for detailed work areas.

To change the CCT, locate the CCT switch on the fixture (often a small slide switch or DIP switch) and move it to your desired setting. This adjustment should typically be done before the final installation of the diffuser or during initial setup.

6.2 Adjusting Wattage/Brightness

The fixture also features adjustable wattage, which directly impacts its brightness (lumen output). The available settings are:

• 30W: 3500 lumens
• 40W: 4600 lumens
• 50W: 6000 lumens

Similar to the CCT adjustment, a separate switch (often a DIP switch) on the fixture allows you to select the desired wattage. Adjust this setting to achieve the appropriate brightness for your space. This adjustment is typically performed during initial setup.

Note: The fixture is dimmable. If connecting to an external dimmer switch, ensure compatibility with LED fixtures. The internal wattage/brightness selection sets the maximum output for external dimming.

7. Maintenance

Regular maintenance ensures optimal performance and longevity of your LED fixture.

• Cleaning: Disconnect power before cleaning. Use a soft, dry, or slightly damp cloth to wipe the exterior of the fixture. Avoid abrasive cleaners, solvents, or sprays that could damage the finish or electrical components.
• Inspection: Periodically check for any loose wiring or physical damage. If any issues are found, disconnect power and consult a qualified electrician.
• LEDs: The LED components are integrated and not user-replaceable. Do not attempt to open the sealed LED module.

8. Troubleshooting

If you encounter issues with your FAITHSAIL LED Wraparound Light, refer to the following common problems and solutions:

If the problem persists after attempting these solutions, please contact FAITHSAIL customer support.

9. Warranty and Support

FAITHSAIL products are manufactured to high-quality standards. While specific warranty details are not provided in this manual, please retain your proof of purchase for any warranty claims.

For technical support, warranty inquiries, or replacement parts, please contact FAITHSAIL customer service through their official website or the retailer where the product was purchased.

You can visit the FAITHSAIL store on Amazon for more information: FAITHSAIL Store