Introduction
This manual provides detailed instructions for the assembly, operation, and maintenance of your TMEOSK Twin Wooden Floor Bed with House-Shaped Headboard. Please read all instructions carefully before beginning assembly and retain this manual for future reference. Ensure all components are present and undamaged before proceeding.
Safety Information
- Keep all small parts and packaging materials away from children during assembly.
- Ensure all screws and fasteners are securely tightened before use. Periodically check and re-tighten as necessary.
- Do not exceed the maximum weight capacity of 250 lbs for the Twin size bed.
- This bed is designed for indoor use only.
- Do not stand or jump on the bed frame.
Package Contents
Before assembly, verify that all parts listed below are included in your package. If any parts are missing or damaged, please contact customer support.
- Bed Frame Components (Side Rails, Headboard/Footboard sections, House-shaped frame pieces)
- Wooden Slats
- Hardware Pack (Screws, bolts, nuts, Allen wrench)
- Assembly Instructions (This manual)
Setup and Assembly
Assembly is required for this product. It is recommended to have two people for easier and safer assembly. Please follow the steps below carefully.
Step 1: Unpack and Identify Components
Carefully remove all components from the packaging. Lay them out on a clean, soft surface (like a carpet) to prevent scratches. Identify each part by comparing it to the parts list (if provided in the physical manual) or the general description in the "Package Contents" section.

Image: Overview of the bed frame components with key dimensions. This image illustrates the various parts and their approximate sizes, including the house-shaped headboard, side rails, and slat support structure. Overall dimensions are 78 inches long, 41.7 inches wide, and 39.2 inches high.
Step 2: Assemble the Headboard and Footboard Sections
Begin by connecting the vertical and horizontal pieces that form the house-shaped headboard and the corresponding footboard section. Use the provided screws and the Allen wrench to secure these connections. Do not fully tighten screws until all parts are loosely assembled.
Step 3: Attach Side Rails
Connect the side rails to the assembled headboard and footboard sections. Ensure the pre-drilled holes align correctly. Insert the bolts and tighten them partially. Once all four corners are connected, gently push the frame into its final shape and then fully tighten all bolts and screws.
Step 4: Install Wooden Slats
Place the wooden slats across the bed frame, ensuring they are evenly spaced and rest securely on the support ledges. Secure each slat using the provided screws, if applicable, to prevent movement. This bed does not require a box spring.

Image: The fully assembled TMEOSK Twin Wooden Floor Bed, ready for use. This image shows the bed with a mattress and bedding, highlighting its low-profile design and the distinctive house-shaped headboard in a child's room setting.
Operation and Use
Your TMEOSK Twin Wooden Floor Bed is designed for comfortable and safe use. Follow these guidelines for optimal performance.
- Mattress Placement: This bed is designed to accommodate a Twin size mattress with a thickness of 6-8 inches. Simply place your mattress directly onto the wooden slats. No box spring is required.
- Weight Capacity: The Twin size bed has a maximum weight capacity of 250 lbs. Do not exceed this limit to ensure structural integrity and safety.
- Low Profile Design: The bed's low height is a safety feature, reducing the risk of falls, especially for younger users.
Maintenance and Care
Proper care will extend the life and appearance of your bed frame.
- Cleaning: Wipe the wooden surfaces with a damp cloth. Avoid using harsh chemicals or abrasive cleaners, which can damage the finish.
- Fastener Check: Periodically check all screws, bolts, and connections to ensure they remain tight. Re-tighten if any looseness is detected.
- Avoid Moisture: Keep the bed frame away from excessive moisture or direct sunlight to prevent warping or fading of the wood.
Troubleshooting
If you encounter any issues with your bed frame, refer to the following common solutions.
- Squeaking Noises: Squeaking often indicates loose connections. Re-tighten all screws and bolts on the frame. Ensure slats are properly seated and secured.
- Unstable Frame: If the bed feels wobbly, check that all components are correctly assembled and all fasteners are fully tightened. Ensure the bed is on a level surface.
- Missing Parts: If you discover missing parts during assembly, do not attempt to force assembly. Contact customer support immediately for replacement parts.
Specifications
| Model Number | Wooden Floor Bed Frames-TMEOSK3616 |
| Brand | TMEOSK |
| Size | Twin |
| Overall Product Dimensions | 78"L x 41.7"W x 39.2"H (Twin) |
| Material | Pine Wood + MDF |
| Color | White |
| Compatible Mattress Thickness | 6-8 inches |
| Bed Weight Capacity | 250 lbs (Twin) |
| Assembly Required | Yes |
| Product Care Instructions | Wipe with Damp Cloth |
| Item Weight | 21 lbs (Twin) |
| UPC | 765133790180 |
Note: Dimensions and weights are approximate and may vary slightly.
Warranty and Support
This product is manufactured with quality materials and craftsmanship. While specific warranty details are not provided in this manual, please retain your proof of purchase for any warranty claims.
For assistance with assembly, missing parts, or any other product-related inquiries, please contact the retailer or manufacturer's customer support. Refer to your purchase documentation for contact information.