SANODESK Single Motor 2 Stage Electric Height Adjustable Standing Desk Frame - Instruction Manual

1. Introduction

Thank you for choosing the SANODESK Single Motor 2 Stage Electric Height Adjustable Standing Desk Frame. This manual provides detailed instructions for assembly, operation, maintenance, and troubleshooting to ensure safe and efficient use of your new desk frame. This product is designed to provide a versatile and ergonomic workspace, allowing you to easily switch between sitting and standing positions.

Figure 1.1: The SANODESK Single Motor 2 Stage Electric Height Adjustable Standing Desk Frame (Black Frame Only).

2. Important Safety Information

Please read all safety warnings and instructions carefully before assembly and use. Failure to follow these instructions may result in serious injury or damage to the product.

• This desk has a weight capacity of 176 lbs (79.8 kg). Exceeding this limit can cause damage to the desk or injury.
• Properly anchor the desk to the floor to ensure stability.
• Assembly is required, and it is recommended to follow the provided instructions carefully.
• Keep children and pets away from the desk during operation.
• Ensure no obstacles are in the path of the desk's movement (up or down).
• Do not sit or stand on the desk frame.
• Disconnect power before cleaning or performing maintenance.

3. Package Contents

Before beginning assembly, please verify that all components listed below are present and undamaged. If any parts are missing or damaged, please contact customer service.

• Desk Frame Components (Legs, Crossbar, Feet)
• Single Motor
• LED Memory Control Panel
• Power Adapter and Cable
• Assembly Hardware (Screws, Washers, Allen Keys)
• Instruction Manual
• Note: Desk board/tabletop is not included and must be purchased separately.

Figure 3.1: Illustration showing the desk frame with a tabletop and monitors. Please note that the desk board is not included with the frame.

4. Setup and Assembly

Assembly of the SANODESK frame is designed to be straightforward. It is recommended to assemble the desk in the area where it will be used. Two people are recommended for easier assembly, especially when attaching the tabletop.

4.1 Assembly Steps

1. Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, flat surface. Check against the package contents list.
2. Assemble Legs and Feet: Attach the feet to the bottom of each leg column using the provided screws. Ensure they are securely fastened.
3. Connect Crossbar: Attach the adjustable crossbar to the top of the leg columns. This crossbar allows for adjustment to accommodate various tabletop widths.
4. Install Motor and Control Panel: Mount the single motor and the LED memory control panel to the designated areas on the frame, typically underneath the crossbar or side of the frame. Connect all necessary cables.
5. Attach Tabletop (Not Included): Place your chosen tabletop onto the assembled frame. Ensure it is centered and aligned. Secure the tabletop to the frame using appropriate screws (not included, as tabletops vary). The frame is designed to accommodate tabletops with minimum width of 39.3 inches and maximum width of 63 inches, and depth from 19.7 inches to 31.5 inches.
6. Cable Management: Organize and secure all cables using cable ties or clips to prevent tangling and ensure smooth operation.

Figure 4.1: The desk frame is designed for easy assembly, typically taking around 30 minutes.

Figure 4.2: The adjustable frame can accommodate most standard tabletop sizes, ranging from 19.7" to 31.5" in depth and 39.3" to 63" in width.

5. Operating Instructions

Your SANODESK frame features an intuitive LED memory control panel for easy height adjustments and preset memory functions.

5.1 Adjusting Height

• To raise the desk, press and hold the UP arrow button.
• To lower the desk, press and hold the DOWN arrow button.
• Release the button when the desk reaches your desired height. The desk operates smoothly and quietly.

Figure 5.1: The electric lifting system allows for a height range from 28.1 inches to 45.7 inches.

5.2 Using Memory Presets

The control panel includes 4 memory keys (1, 2, 3, 4) to store and recall your preferred sitting and standing heights.

1. Set a Memory Position: Adjust the desk to your desired height using the UP/DOWN buttons. Press the "M" button (or similar memory set button, if present, otherwise directly press a number button after reaching desired height) followed by one of the number buttons (1, 2, 3, or 4). The display will show "S-" or a beep will confirm the setting.
2. Recall a Memory Position: Press the corresponding number button (1, 2, 3, or 4) for your desired preset height. The desk will automatically move to that stored position.

Figure 5.2: The LED Memory Control Panel features UP/DOWN arrows and four memory preset buttons for quick height adjustments.

5.3 Side Storage Hooks

The desk frame may include convenient side storage hooks, ideal for hanging headphones, bags, or other accessories, keeping your workspace tidy.

Figure 5.3: Utilize the integrated side storage hooks for convenient organization of your accessories.

6. Maintenance

Regular maintenance will help prolong the life and ensure the smooth operation of your SANODESK frame.

• Cleaning: Wipe the frame surface with a soft, damp cloth. Avoid harsh chemicals or abrasive cleaners. The powder-coated surface is waterproof and rustproof.
• Check Connections: Periodically check all screws and bolts to ensure they are tight. Loose connections can affect stability.
• Cable Management: Ensure cables remain tidy and are not pinched or tangled, which could impede movement or cause damage.
• Weight Distribution: Distribute weight evenly on the tabletop to prevent strain on the motor and frame.

7. Troubleshooting

If you encounter any issues with your SANODESK frame, please refer to the following common problems and solutions. If the problem persists, contact customer service.

8. Product Specifications

Detailed specifications for the SANODESK Single Motor 2 Stage Electric Height Adjustable Standing Desk Frame.

• Brand: SANODESK
• Model Number: EP1
• Color: Black
• Base Material: Alloy Steel
• Finish Type: Powder Coated
• Style: Modern
• Product Dimensions (Frame): 30"D x 60"W x 24.6"H (Adjustable width/depth for tabletop)
• Minimum Height: 28.1 inches
• Maximum Height: 45.7 inches
• Maximum Weight Capacity: 176 lbs (79.8 kg)
• Motor Type: Single Motor
• Control Panel: LED Memory Control Panel with 4 presets
• Assembly Required: Yes
• Included Components: Desk Mount (Frame components, motor, control panel, hardware)

Figure 8.1: The robust design supports a load capacity of 176 lbs, ensuring stability for your workspace.

9. Warranty and Customer Support

SANODESK is committed to your satisfaction. We offer a limited warranty on our products.

9.1 Warranty Information

• The product comes with a limited warranty. Specific warranty details for the motor (2 years) and desk frame (5 years) are often provided at the point of purchase or on the product packaging. Please refer to your purchase documentation for precise terms.
• A 30-day return or exchange service is provided if you encounter any problems upon receiving or using the product.

9.2 Customer Support

If you have any questions, require assistance with assembly, or experience issues not covered in the troubleshooting section, please do not hesitate to contact SANODESK customer service. You can typically reach customer service through the order page where you purchased the product. We are dedicated to providing prompt and helpful assistance.