OurLeeme 12V 1100 GPH Automatic Bilge Pump Instruction Manual

1. Introduction

This manual provides essential information for the safe and efficient operation of your OurLeeme 12V 1100 GPH Automatic Bilge Pump. Please read these instructions carefully before installation and use, and retain them for future reference.

Product Features:

• Low Power Consumption: Highly efficient with very low energy usage and high capacity.
• Compact Size: Small, lightweight design, space-saving, quiet operation, and low vibration.
• High Flow Rate: Provides a large water output for rapid water evacuation.
• Fully Automatic Operation: Equipped with an integrated electronic Reed sensor system for easy, fully automatic control.
• Waterproof Design: Fully submersible and fire-resistant with anti-airlock design and moisture-tight seals.
• Durable Construction: Stainless steel shaft, impact-resistant plastic housing with anti-rust and corrosion-resistant properties.
• Dry Run Protection: Designed not to burn out when running dry.
• Versatile Use: Compatible with both fresh and saltwater.

Figure 1: OurLeeme 12V 1100 GPH Automatic Bilge Pump. This image shows the compact design of the bilge pump with its white and blue casing and integrated wiring.

2. Safety Information

Please observe the following safety warnings to prevent injury or damage to the product.

Figure 2: Product Warning Label. This label indicates a choking hazard due to small parts, making it unsuitable for children under 3 years old. It also displays CE and UKCA compliance marks.

• Choking Hazard: Contains small parts. Keep away from children under 3 years of age.
• Ensure all electrical connections are properly insulated and protected from water ingress.
• Do not operate the pump if the wiring is damaged.
• Always disconnect power before performing any maintenance or installation.
• This pump is designed for pumping water only. Do not use it for flammable liquids, chemicals, or other hazardous materials.

3. Package Contents

Verify that all items are present in the package:

• 1 x OurLeeme 12V 1100 GPH Automatic Bilge Pump

4. Specifications

Figure 3: Product Dimensions. This image illustrates the length (14.5 cm / 5.7"), width (7.8 cm / 3.1"), and height (10 cm / 3.9") of the bilge pump.

5. Installation and Setup

Proper installation is crucial for the pump's performance and longevity.

Mounting:

• Position the pump in the lowest part of the bilge or desired water collection area.
• Ensure the pump is securely mounted to prevent movement during operation.
• The pump is fully submersible.

Hose Connection:

• Connect a 0.75-inch (19mm) discharge hose to the pump's outlet.
• Secure the hose with a hose clamp to prevent leaks.
• Route the discharge hose upwards and overboard, ensuring a continuous downward slope to prevent backflow.

Figure 4: Typical Bilge Pump Installation. This image shows the bilge pump positioned within a boat's bilge, ready for operation.

6. Wiring Instructions

Correct wiring is essential for safe and automatic operation. Always disconnect the power source before wiring.

Wire Identification:

• Black Wire: Connect to the negative (-) terminal of the 12V power source.
• Red Wire: Connect to the positive (+) terminal for Manual Mode operation.
• Blue Wire: Connect to the positive (+) terminal for Automatic Mode operation.

Figure 5: Wiring Details. This close-up shows the black (negative), red (manual positive), and blue (automatic positive) wires emerging from the pump.

Wiring Diagram:

Before wiring, open the filter and remove the foam block located under the float mechanism.

Figure 6: Wiring Diagram. This diagram illustrates connections for both Automatic Mode (Black to Battery -, Blue to Battery +) and Manual Mode (Black to Battery -, Red to Battery +). Note: The diagram shows a "Brown" wire for manual mode, but the product description and other images indicate "Red" for manual positive connection. Please follow the Red wire for manual positive connection as per the product description and Figure 5.

• Automatic Mode: Connect the Black wire to the battery's negative terminal. Connect the Blue wire to the battery's positive terminal. The pump will activate automatically when the water level rises.
• Manual Mode: Connect the Black wire to the battery's negative terminal. Connect the Red wire to the battery's positive terminal. The pump will operate continuously as long as power is supplied.
• It is recommended to install a fuse (not included) in the positive line for circuit protection.

7. Operating Instructions

The OurLeeme Bilge Pump offers both automatic and manual operation modes.

Automatic Operation:

• When wired for Automatic Mode (Blue wire to positive), the pump's internal float switch will detect rising water levels.
• The pump will automatically activate when the water reaches a critical level.
• Once the water level drops below the sensor, the pump will automatically shut off.

Figure 7: Automatic Operation Cycle. This sequence illustrates how the pump activates when water reaches a critical level and deactivates once the water is pumped out and the level drops.

Manual Operation:

• When wired for Manual Mode (Red wire to positive), the pump will run continuously as long as power is supplied.
• This mode is suitable for situations requiring continuous pumping or for testing the pump.
• Always monitor the pump during manual operation to prevent dry running for extended periods, although the pump is designed not to burn out when dry.

8. Maintenance

Regular maintenance ensures optimal performance and extends the lifespan of your bilge pump.

• Inspect Regularly: Periodically check the pump for debris, such as leaves, hair, or other foreign objects that may obstruct the intake or impeller.
• Clean Intake Screen: The pump features a removable filter/intake screen. Clean it regularly to ensure unrestricted water flow.
• Check Wiring: Inspect all wiring connections for corrosion, fraying, or loose terminals. Ensure connections are secure and waterproof.
• Test Operation: Regularly test the pump's automatic and manual functions to confirm it is operating correctly. For automatic mode, introduce water into the bilge to trigger the float switch.
• Winterization: In freezing conditions, ensure the pump is drained and protected from ice formation, or remove it for storage.

9. Troubleshooting

If you encounter issues with your bilge pump, refer to the following common problems and solutions:

10. Warranty and Support

Specific warranty information is not provided in the product details. For warranty claims or technical support, please contact your retailer or the manufacturer, OurLeeme, directly. Keep your purchase receipt as proof of purchase.