Introduction
This manual provides essential instructions for the safe and efficient setup, operation, and maintenance of your Funsicle Quickset 12ft x 36in Round Inflatable Above Ground Swimming Pool. This spacious pool, measuring 12 feet in diameter and 36 inches deep, is designed for recreational use, accommodating up to 6 people. Please read all instructions carefully before installation and use to ensure proper function and safety.
Safety Information
WARNING: Failure to follow these instructions can result in serious injury or death.
- Adult Supervision Required: Never leave children unattended in or near the pool. Constant adult supervision is mandatory.
- No Diving: This pool is not designed for diving. Shallow water can cause serious injury.
- Electrical Safety: Ensure all electrical components, including the filter pump, are connected to a GFCI (Ground-Fault Circuit Interrupter) protected outlet. Do not use extension cords. Keep electrical cords away from water.
- Site Preparation: Install the pool on a firm, level surface free of sharp objects, debris, or uneven ground. Uneven ground can cause the pool to collapse, leading to injury or water spillage.
- Local Regulations: Before purchasing and setting up this product, review and check your local HOA rules, building codes, and restrictions regarding private above-ground pools. Not all housing agencies permit them.
- Chemical Handling: Handle pool chemicals according to manufacturer's instructions. Keep chemicals out of reach of children.
- Drainage: Ensure proper drainage away from the pool area to prevent water accumulation.
Package Contents
Verify that all components listed below are present in your package:
- Funsicle Quickset Pool Liner (12ft x 36in)
- 110-120V RX200 Filter Pump
- Type D Filter Cartridge
- Repair Patch
- Hoses and connectors for filter pump
Image: Included RX200 filter pump and Type D filter cartridge.
Setup Instructions
Follow these steps for a quick and hassle-free pool setup:
- Site Selection and Preparation:
- Choose a flat, level area in your backyard, away from power lines, trees, and structures.
- Clear the area of any sharp objects, rocks, roots, or debris that could puncture the pool liner.
- Lay down a ground cloth (not included) for added protection.
- Unpack the Pool: Carefully remove the pool liner from its packaging. Allow it to warm up in the sun for a short period to make the material more pliable.
- Inflate the Top Ring: Locate the air valve on the top inflatable ring. Use an air pump (not included) to inflate the ring until it is firm but not overinflated. Do not use a high-pressure air compressor.
- Fill with Water: Begin filling the pool with water. As the water level rises, the pool walls will automatically rise and take shape. Smooth out any wrinkles on the bottom of the pool as it fills to ensure an even base.
- Connect the Filter Pump:
- Attach the hoses from the pool's inlet and outlet fittings to the RX200 filter pump.
- Ensure all connections are secure to prevent leaks.
- Place the filter pump on a stable, level surface at least 6 feet away from the pool.
- Plug the filter pump into a GFCI-protected electrical outlet.
Image: The Funsicle Quickset pool fully set up with its filter pump connected.
Image: Diagram highlighting key features like durable construction, easy inflation, and effective filtration.
Image: Visual representation of the pool's 36-inch height.
Image: Cross-section view illustrating the multi-layered ToughMesh construction for durability.
Operating Instructions
To ensure optimal performance and water quality, follow these operating guidelines:
- Filter Pump Operation: Run the RX200 filter pump daily for at least 4-6 hours to circulate and filter the pool water. The exact duration may vary based on usage and environmental conditions.
- Water Level: Maintain the water level between the MIN and MAX fill lines indicated on the pool liner. An appropriate water level is crucial for proper pump function and pool stability.
- Water Chemistry: Regularly test your pool water using a test kit (not included) to ensure proper pH and chlorine levels. Maintain pH between 7.2 and 7.6 and chlorine levels as recommended by your chemical supplier.
Image: Water being returned to the pool through the filter system's jet.
Maintenance
Regular maintenance is key to extending the life of your pool and ensuring clean water.
- Skimming and Vacuuming: Daily skim debris from the water surface and periodically vacuum the pool bottom to remove settled dirt and leaves.
- Filter Cartridge Cleaning/Replacement: The Type D filter cartridge should be rinsed with a garden hose every few days, depending on pool usage. Replace the filter cartridge every 2-4 weeks, or sooner if it remains dirty after rinsing. Only use Funsicle Type D filter cartridges.
- Water Treatment: Follow a consistent water treatment regimen using appropriate pool chemicals to prevent algae growth and maintain sanitation.
- Draining the Pool: When preparing for storage or for a full water change, use the 2-in-1 drainage plug for convenient lock and unlock. No tools are required for drainage.
Image: Close-up of a Funsicle Type D filter cartridge, essential for water filtration.
Troubleshooting
Refer to this section for common issues and their solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Filter pump not running | No power; GFCI tripped; clogged filter; air in system. | Check power connection; reset GFCI; clean/replace filter cartridge; bleed air from pump system. |
| Water not clear | Insufficient filtration; improper chemical balance; heavy usage. | Run pump longer; clean/replace filter; test and adjust water chemistry (chlorine, pH); shock treat pool. |
| Pool losing water/leaking | Puncture in liner; loose hose connections; overfilling. | Inspect liner for holes and use repair patch; tighten all hose clamps; ensure water level is not above recommended line. |
| Pool not maintaining shape | Uneven ground; insufficient water fill; top ring not fully inflated. | Ensure pool is on perfectly level ground before filling; fill to recommended water level; re-inflate top ring if soft. |
Storage
Proper storage will prolong the life of your Funsicle pool.
- Drain the Pool: Completely drain all water from the pool using the drainage plug.
- Clean and Dry: Thoroughly clean the pool liner and all components. Ensure everything is completely dry before folding to prevent mold and mildew.
- Disassemble: Disconnect the filter pump and hoses. Deflate the top ring.
- Fold and Store: Carefully fold the pool liner to avoid creases. Store the pool, pump, and accessories in a dry, cool place, away from direct sunlight and extreme temperatures.
Specifications
| Feature | Detail |
|---|---|
| Brand | Funsicle |
| Model Number | P1A01236A |
| Product Dimensions | 144"L x 144"W x 36"H (12ft diameter x 36in height) |
| Shape | Round |
| Capacity | 74 Gallons (Note: This capacity seems unusually low for the dimensions provided in the product data. Please refer to the product packaging for the most accurate water capacity.) |
| Color | Gray |
| Material | ToughMesh, Polyvinyl Chloride (PVC) |
| Included Components | Filter Cartridge, Filter Pump, Repair Patch |
| UPC | 193802325959 |
| Assembly Required | Yes |
Warranty and Support
The Funsicle Quickset Pool and its included pump come with a 1-year manufacturer's warranty. This warranty covers defects in materials and workmanship under normal use.
For warranty claims, technical support, or replacement parts, please contact Funsicle customer service directly. Refer to the contact information provided on your product packaging or the official Funsicle website.
