LS2 Advant X Carbon Modular Helmet Instruction Manual

1. Introduction

The LS2 Advant X Carbon Modular Helmet is engineered for optimal safety, comfort, and versatility. This manual provides essential information for the proper use, care, and maintenance of your helmet. Please read it thoroughly before using your helmet to ensure maximum protection and longevity.

Figure 1.1: LS2 Advant X Carbon Modular Helmet in Matte Black.

2. Safety Information

Your LS2 Advant X Carbon Modular Helmet meets or exceeds stringent safety standards. It is crucial to understand and adhere to all safety guidelines to ensure your protection.

2.1 Certifications

• Meets or exceeds DOT FMVSS 218.
• Meets or exceeds ECE 22.06.
• ECE "P" (Protective) and "J" (Jet) certified, allowing use as both a full-face and open-face helmet.

2.2 Legal Disclaimer

This helmet complies with US Federal Motor Vehicle Safety Standard 218 (FMVSS 218) (DOT FMVSS No. 218 Certified).

2.3 Emergency Release System

The helmet is equipped with an Emergency Release Cheek Pad System. In case of an emergency, this system allows for quick removal of the cheek pads, facilitating safer helmet removal by trained personnel.

3. Setup

Proper fitment is critical for helmet safety and comfort. Follow these steps to ensure your helmet is set up correctly.

3.1 Sizing Information

To determine your correct helmet size, measure your head circumference just above your eyebrows. Refer to the sizing chart below. The Advant X Helmet is designed for an intermediate oval head shape. If you are between sizes or have a round head shape, it is recommended to size up for a better fit, as this helmet tends to run small.

Figure 3.1: Head Measurement and Sizing Chart.

4. Operating the Helmet

Familiarize yourself with the various features and controls of your Advant X Carbon helmet.

4.1 Modular System

The Advant X features a 180-degree modular system, allowing the chin bar to flip completely to the rear of the helmet. This provides the flexibility of an open-face helmet while maintaining the option for full-face protection. To operate, locate the release mechanism on the chin bar, activate it, and pivot the chin bar upwards and backward until it locks into place.

Figure 4.1: Helmet in open-face configuration with chin bar rotated to the rear.

4.2 Face Shield (Visor)

The "A Class" polycarbonate face shield is optically correct, scratch-resistant, and UV-resistant. It features a quick-release mechanism for easy removal and replacement. The helmet includes a Pinlock insert for fog resistance.

• Opening/Closing: Use the tab located on the top center of the face shield to raise or lower it.
• Removal/Installation: Consult the quick-release mechanism instructions provided with your helmet for detailed steps on removing and installing the face shield.
• Pinlock Insert: The included Pinlock insert should be installed on the inside of the face shield according to the Pinlock instructions to prevent fogging.

Figure 4.2: Available Advant X Shield Options.

4.3 Built-in Sun Shield

A retractable internal sun shield is integrated into the helmet for convenience. Operate the sun shield using the slider mechanism located on the side of the helmet.

4.4 Ventilation System

The helmet features a fully adjustable, multi-port dynamic flow-through ventilation system with channeled EPS to keep you cool. Locate the various vents (e.g., chin, top, rear exhaust) and adjust them as needed for airflow.

4.5 Chin Strap

The DOT-approved micrometric quick-release chin strap ensures a secure and easy closure. To fasten, insert the tab into the buckle until it clicks. To release, pull the red tab to disengage the mechanism.

Figure 4.3: Helmet interior with micrometric quick-release chin strap.

5. Maintenance

Regular maintenance will prolong the life and effectiveness of your helmet.

5.1 Liner Care

The removable technical fabric liner is designed to keep you cool and can be washed. Carefully remove the liner components (cheek pads, comfort liner) according to the instructions provided with your helmet. Hand wash with mild soap and water, then air dry completely before reinstallation.

5.2 Face Shield Cleaning

Clean the face shield with a soft, damp cloth and mild soap or a specialized helmet visor cleaner. Avoid abrasive materials or harsh chemicals that can scratch or damage the shield's coating. For the Pinlock insert, follow its specific cleaning instructions.

5.3 Shell Cleaning

Clean the carbon fiber shell with a soft cloth and mild soap and water. Do not use petroleum-based products, solvents, or harsh cleaners, as these can damage the helmet's finish and materials.

6. Troubleshooting

This section addresses common concerns you might encounter with your helmet.

6.1 Fit Issues

• Helmet feels too tight: Ensure you have selected the correct size based on the sizing chart. Remember this helmet runs small, so consider sizing up if you are between sizes or have a rounder head shape. The liner will break in slightly over time, but it should not be uncomfortably tight initially.
• Helmet feels too loose: A loose helmet compromises safety. Re-check your head measurement against the sizing chart. If the helmet is too large, it must be replaced with a smaller size.

6.2 Visor Fogging

If your visor fogs, ensure the Pinlock insert is correctly installed and sealed against the main face shield. If fogging persists, ensure adequate ventilation by opening helmet vents.

7. Specifications

Key technical specifications for the LS2 Advant X Carbon Modular Helmet.

Figure 7.1: Technical Specifications Summary.

8. Warranty and Support

For specific warranty details and support inquiries regarding your LS2 Advant X Carbon Modular Helmet, please refer to the warranty card included with your purchase or visit the official LS2 Helmets website. You may also contact the authorized seller from whom you purchased the helmet for assistance.

LS2 Helmets can be found at their official store: LS2 Store on Amazon.