Swimline Hydrotools 19-Inch Sand Filter Combo & GAME Adapter Kit

Download PDFFree PDF. The Save button below keeps a bookmark and private notes in your account.

Swimline Hydrotools 19-Inch Sand Filter Combo Set & GAME Adapter Kit User Manual

Model: Hydrotools 19-Inch Sand Filter Combo & GAME Adapter Kit

Brand: Swimline

1. Introduction

This manual provides detailed instructions for the safe and efficient operation, installation, and maintenance of your Swimline Hydrotools 19-Inch Sand Filter Combo Set and the GAME 40mm to 1 1/2-Inch Adapter Conversion Kit. Please read this manual thoroughly before attempting to install or operate the equipment. Proper installation and maintenance are crucial for optimal performance and longevity of the product.

2. Safety Information

WARNING: Failure to follow these instructions can result in serious injury or death.

  • Always disconnect power to the pump before performing any service or maintenance.
  • Ensure all electrical connections are made by a qualified electrician and comply with local codes.
  • Do not operate the filter system if any part is damaged or missing.
  • Never operate the pump dry. Ensure the pump is primed with water before starting.
  • Maintain proper water chemistry in your pool to prevent damage to the filter system and ensure safe swimming conditions.
  • Keep children away from the filter system during operation and maintenance.
  • The sand filter operates under pressure. Ensure all clamps and connections are secure before starting.

3. Package Contents

Verify that all components are present before beginning installation:

  • Swimline Hydrotools 19-Inch Sand Filter Tank
  • 0.9 THP DOE Compliant Pump (4500 GPH)
  • Filter Base/Stand
  • Multi-Port Valve
  • 3-Prong Plug & Power Cord
  • GAME 40mm to 1 1/2-Inch Adapter Conversion Kit (2 Count)
  • Necessary hoses and clamps for filter connection (may vary)
Swimline Hydrotools 19-Inch Sand Filter Combo Set and GAME Adapter Kit

Figure 3.1: Overview of the Swimline Hydrotools 19-Inch Sand Filter Combo Set and the GAME 40mm to 1 1/2-Inch Adapter Conversion Kit components. The image displays the sand filter tank, pump, and two adapter pieces.

4. Setup & Installation

4.1. Swimline Hydrotools Sand Filter Combo Set Installation

  1. Positioning: Place the filter base on a firm, level surface, preferably concrete, as close to the pool as possible. Ensure adequate drainage and protection from direct weather if not designed for outdoor exposure.
  2. Tank Assembly: Place the sand filter tank onto the filter base.
  3. Adding Filter Media:
    • Remove the multi-port valve and cover the standpipe opening with a small cup or plastic bag to prevent sand from entering.
    • Carefully add the recommended amount of filter sand (approximately 175 pounds for this 19-inch tank). Sand is not included with the system.
    • Ensure the sand level is appropriate, typically leaving 6-8 inches from the top of the tank.
    • Remove the cover from the standpipe opening.
  4. Multi-Port Valve Installation:
    • Carefully place the multi-port valve onto the top of the tank, ensuring the standpipe aligns correctly with the valve's opening.
    • Secure the multi-port valve to the tank using the provided clamp or flange. Ensure a tight, leak-free seal.
  5. Pump Connection:
    • Connect the pump to the multi-port valve's "PUMP" port using the provided hose and clamps.
    • Connect the pump's suction side to the pool's skimmer line.
    • Connect the multi-port valve's "RETURN" port to the pool's return line.
    • Connect the "WASTE" port to a suitable backwash line or drainage area.
  6. Electrical Connection: Plug the pump's power cord into a grounded electrical outlet. Ensure the outlet is protected by a Ground Fault Circuit Interrupter (GFCI).
Swimline Hydrotools 19-Inch Sand Filter Combo Set

Figure 4.1: The Swimline Hydrotools 19-Inch Sand Filter Combo Set, showing the sand filter tank, pump, and multi-port valve assembled on its stand. This image illustrates the primary components of the filtration system.

Hydrotools Sand Filter Capacity Details

Figure 4.2: Diagram detailing the capacity and construction of the Hydrotools sand filter. It highlights the 19-inch tank size, suitability for pools up to 19,000 gallons, and a sand capacity of 175 pounds (sand not included). Also notes heavy-duty, non-corrosive design and includes filter connection hoses.

4.2. GAME 40mm to 1 1/2-Inch Adapter Conversion Kit Installation

The GAME adapter conversion kit is designed to allow 40mm hoses to be used with standard 1 1/4 inch or 1 1/2 inch filter ports, commonly found on Intex and Bestway pools, enabling integration with non-Intex brand filters.

  1. Identify Ports: Determine which pool or filter ports require conversion from 1 1/4 or 1 1/2 inch to accommodate 40mm hoses.
  2. Attach Adapter: Screw the threaded end of the GAME adapter into the larger 1 1/4 or 1 1/2 inch port. Ensure the O-ring is properly seated to create a watertight seal.
  3. Connect Hose: Attach the 40mm hose to the smaller, inner diameter side of the adapter. Secure with a hose clamp if necessary.
  4. Test for Leaks: Once connections are made, run the pump and check for any leaks around the adapter connections.
GAME 40mm to 1 1/2-Inch Adapter Conversion Kit

Figure 4.3: The two pieces of the GAME 40mm to 1 1/2-Inch Adapter Conversion Kit. These adapters facilitate connecting 40mm hoses to larger standard pool filter ports.

GAME Adapter Dimensions

Figure 4.4: A single GAME adapter with its approximate dimensions: 2.3 inches in width and 1.8 inches in height. This provides a visual reference for the adapter's size.

Adapter O-rings

Figure 4.5: Two black O-rings, essential for creating a watertight seal when installing the GAME adapters. These rings prevent leaks at the connection points.

5. Operating Instructions

The multi-port valve on your sand filter allows for various operational modes. Always turn off the pump before changing the valve position.

  • FILTER: Normal filtering mode. Water flows through the sand bed, trapping debris, and returns to the pool.
  • BACKWASH: Used for cleaning the filter sand. Water flows in reverse through the sand bed, dislodging trapped debris, and is directed out the waste port.
  • RINSE: Used after backwashing to settle the sand bed and flush out any remaining dirty water from the valve before returning to filter mode.
  • WASTE: Bypasses the filter and sends water directly out the waste port. Useful for vacuuming heavy debris directly to waste or lowering pool water level.
  • RECIRCULATE: Bypasses the filter and circulates water directly back to the pool. Useful for mixing chemicals without filtering.
  • WINTER: Used for winterizing the filter system.

5.1. Initial Startup and Backwashing

  1. Ensure all connections are secure and the pool is filled to the proper level.
  2. Set the multi-port valve to the "BACKWASH" position.
  3. Turn on the pump. Backwash for 2-3 minutes, or until the water in the sight glass (if present) runs clear.
  4. Turn off the pump.
  5. Set the multi-port valve to the "RINSE" position.
  6. Turn on the pump. Rinse for 30-60 seconds.
  7. Turn off the pump.
  8. Set the multi-port valve to the "FILTER" position.
  9. Turn on the pump. The system is now operating in normal filter mode.

Monitor the pressure gauge (if equipped). When the pressure rises 8-10 PSI above the clean operating pressure, it's time to backwash again.

6. Maintenance

  • Regular Backwashing: Backwash the filter regularly as indicated by the pressure gauge or when water flow decreases.
  • Sand Replacement: Filter sand typically lasts approximately 5 years, depending on water chemistry and backwashing frequency. Replace sand when filtration efficiency decreases significantly.
  • Winterization: Before freezing temperatures, drain all water from the pump, filter, and plumbing lines. Store the pump and multi-port valve in a dry, protected area.
  • General Cleaning: Periodically inspect and clean the pump's strainer basket. Ensure all connections are tight and free of leaks.

7. Troubleshooting

Problem Possible Cause Solution
Low water flow / High pressure Dirty filter sand; Clogged pump strainer basket; Air leak in suction line. Backwash and rinse filter; Clean strainer basket; Check all suction line connections for leaks.
Cloudy pool water Insufficient filtration time; Improper water chemistry; Damaged filter sand; Multi-port valve setting incorrect. Increase filtration time; Test and adjust pool chemistry; Replace filter sand; Ensure valve is on "FILTER".
Pump not priming Air leak in suction line; Low water level in pool; Clogged skimmer/main drain. Check all suction connections; Ensure pool water level is adequate; Clear skimmer/main drain.
Water leaking from valve Worn O-rings/gaskets; Loose clamp. Inspect and replace O-rings/gaskets; Tighten clamp.

8. Specifications

  • Sand Filter Tank Size: 19 inches
  • Sand Capacity: Approximately 175 pounds (sand not included)
  • Pump Horsepower (THP): 0.9 THP (DOE Compliant)
  • Pump Flow Rate: 4500 GPH (Gallons Per Hour)
  • Recommended Pool Size: Up to 19,000 gallons
  • Multi-Port Valve Settings: Filter, Rinse, Recirculate, Winter, Backwash, Waste
  • Adapter Kit Compatibility: Converts 40mm hoses to 1 1/4 inch or 1 1/2 inch filter ports (e.g., Intex & Bestway pools)

9. Warranty & Support

For warranty information or technical support, please contact Swimline customer service. Keep your purchase receipt as proof of purchase. Contact details can typically be found on the manufacturer's website or original product packaging.

Swimline Customer Service: Refer to your product packaging or the official Swimline website for the most current contact information.

© 2023 Swimline. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.