Tornado 24-Inch High Velocity Oscillating Pedestal Fan User Manual

1. Introduction

Thank you for choosing the Tornado 24-inch High Velocity Oscillating Metal Pedestal Fan. This fan is designed for commercial and industrial use, providing powerful airflow with three-speed settings. It features durable construction, adjustable height, and oscillating movement to efficiently circulate air in large spaces. Please read this manual thoroughly before assembly, operation, or maintenance to ensure safe and optimal performance.

2. Important Safety Information

Always follow basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, and injury to persons.

• Read all instructions before using this fan.
• Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over.
• To disconnect the fan, turn controls to the OFF position, then remove the plug from the outlet.
• Do not insert fingers or foreign objects into any opening.
• Do not use outdoors or on wet surfaces.
• This fan is UL Safety Listed and meets OSHA and UL507 standards.

3. Package Contents

Verify that all components are present and in good condition:

• Fan Head Assembly (motor, blades, grille)
• Pedestal Pole (adjustable height)
• Round Base
• Mounting Hardware (screws, washers, hand screw knob)
• Power Cord (6.6 ft)

4. Setup and Assembly

Assembly of the Tornado pedestal fan is straightforward. Follow these steps for proper setup:

1. Attach the Pedestal Pole to the Base: Securely fasten the pedestal pole to the round base using the provided hardware. Ensure it is stable and upright.
2. Mount the Fan Head Assembly: Attach the fan head assembly to the top of the pedestal pole. Use the hand screw knob to tighten and secure the fan head at the desired height. Ensure the fan blades are installed correctly, facing the direction of airflow. Incorrect blade installation can lead to poor airflow and increased noise.
3. Adjust Height: Loosen the hand screw knob on the pedestal pole to adjust the fan's height between 54.53 inches and 73.03 inches. Tighten the knob firmly once the desired height is reached.
4. Position the Fan: Place the fan on a stable, level surface. Ensure there is adequate clearance around the fan for optimal air circulation and oscillation.

Figure 4.1: Fan dimensions, illustrating adjustable height and overall size.

5. Operating Instructions

Once assembled, operating your Tornado pedestal fan is simple:

1. Plug In: Insert the 6.6 ft power cord into a standard electrical outlet.
2. Select Speed: Use the control knob located on the motor housing to select one of the three speed settings:
   • '1' (Low): 6050 CFM
   • '2' (Medium): 6750 CFM
   • '3' (High): 7600 CFM
3. Activate Oscillation: To enable the 70-degree oscillating movement, press down the oscillation pin located on the top of the motor housing. To stop oscillation, pull the pin up.
4. Adjust Vertical Tilt: The fan head can be tilted vertically up to 25 degrees. Loosen the tilt adjustment knob on the side of the fan head, adjust to the desired angle, and then firmly tighten the knob.
5. Turn Off: To turn off the fan, rotate the speed control knob to the '0' position.

Figure 5.1: Fan speed settings and corresponding CFM values.

Figure 5.2: Visual representation of oscillation, vertical tilt, and cord length.

6. Key Features

• Powerful Airflow: Delivers an impressive 7600 CFM airflow on high setting, ideal for large spaces.
• Durable Construction: Built with premium aluminum blades, a powder-coated steel housing, rust-resistant grille, and a heavy-duty steel frame for long-lasting performance. The open-air motor with ball bearings is designed for high-intensity use.
• Adjustable & Oscillating: Features tool-free height adjustment from 54.53" to 73.03", 70-degree oscillation, and a 25-degree vertical tilt for flexible air direction.
• Enhanced Safety: Meets OSHA and UL507 standards, UL Safety listed, and includes a thermal protection motor for peace of mind.
• Quiet & Efficient Operation: Operates at a reasonable noise level of 69 decibels. The 1/4 HP motor runs efficiently, consuming only 185 watts.

Figure 6.1: Illustration of the fan's ball bearing motor for durable performance.

Figure 6.2: Fan controls and safety compliance markings.

7. Maintenance

Regular maintenance ensures the longevity and efficient operation of your fan.

• Cleaning: Always unplug the fan before cleaning. Use a soft, damp cloth to wipe down the exterior surfaces. Do not use abrasive cleaners or allow water to drip into the motor housing.
• Grille Cleaning: The rust-resistant grille can be wiped clean. For thorough cleaning, the grille may be removed following assembly instructions in reverse. Ensure the grille is securely reattached before operating the fan.
• Storage: If storing the fan for an extended period, cover it to protect against dust and store in a dry location.

8. Troubleshooting

If you experience issues with your fan, refer to the following common problems and solutions:

9. Specifications

10. Warranty and Support

The Tornado 24-inch High Velocity Oscillating Pedestal Fan comes with a 1-year limited warranty from the date of purchase. This warranty covers manufacturing defects under normal use.

For warranty claims, technical support, or replacement parts, please contact Tornado customer service. Refer to the product packaging or the official Tornado website for the most current contact information.

Please retain your proof of purchase for warranty validation.

11. Typical Applications

This fan is suitable for a variety of environments requiring high-volume air circulation:

• Warehouses and Factories
• Garages and Workshops
• Barns and Agricultural Settings
• Commercial Spaces
• Covered Patios and Outdoor Areas

Figure 11.1: Examples of suitable environments for the Tornado pedestal fan.