Introduction
This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your new PHILCO Dual Alarm Clock Model 1006-GR. Please read this manual thoroughly before using the device to ensure proper function and to maximize your user experience. Keep this manual for future reference.
Important Safety Instructions
- Read all instructions before operating the appliance.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Product Overview
Front View
The front of the PHILCO Dual Alarm Clock features a clear LED display for time and status indicators.
Image Description: This image displays the front of the PHILCO Dual Alarm Clock. It is a black rectangular device with a prominent green 0.6-inch LED display showing "12:01". Below the time, the "PHILCO" brand name is visible. Small indicators for "Buzzer", "Alarm 1", "Radio", "Sleep", "Alarm 2", and "Radio" are also present around the display.
Top View and Controls
The top panel houses all control buttons for setting time, alarms, radio functions, and volume.
Image Description: This image shows the top of the PHILCO Dual Alarm Clock. It features a speaker grille at the back and an array of control buttons. From left to right, there are buttons for "SOURCE", "-VOLUME+", "-TUNING+", "PRESET", "AL 1", "AL 2", "HOUR", "MINUTE", and "CLOCK". A large "SNOOZE" button is centrally located at the front of the top panel.
Package Contents
Upon opening the package, you will find the PHILCO Dual Alarm Clock, its power adapter, and the owner's manual.
Image Description: This image displays the PHILCO Dual Alarm Clock along with its accessories. The black clock is visible, accompanied by a black power adapter with its cord, and a printed owner's manual titled "PHILCO DUAL ALARM CLOCK RADIO".
Setup
1. Power Connection
- Connect the provided power adapter to the DC input jack on the back of the clock.
- Plug the power adapter into a standard 110V or 220V AC wall outlet. The clock is compatible with both voltages.
- The LED display will light up, indicating the clock is receiving power.
2. Installing Backup Batteries (Optional)
For time and alarm settings retention during a power outage, install backup batteries.
- Locate the battery compartment on the bottom of the clock.
- Open the battery compartment cover.
- Insert two (2) AAA batteries (not included), observing the correct polarity (+ and -) as indicated inside the compartment.
- Close the battery compartment cover securely.
- Note: Backup batteries only maintain time and alarm settings; they do not power the display or alarm functions during a power outage.
Operating Instructions
1. Setting the Time
- Press and hold the CLOCK button until the hour digits begin to flash.
- Press the HOUR button repeatedly to adjust the hour. Observe the PM indicator if setting a PM time.
- Press the MINUTE button repeatedly to adjust the minutes.
- Press the CLOCK button again to confirm and save the time. The digits will stop flashing.
2. Setting Alarms (Alarm 1 and Alarm 2)
The clock features two independent alarms.
- Press and hold the AL 1 button (for Alarm 1) or AL 2 button (for Alarm 2) until the alarm hour digits begin to flash.
- Press the HOUR button to set the desired alarm hour.
- Press the MINUTE button to set the desired alarm minutes.
- Press the AL 1 or AL 2 button again to confirm the alarm time.
- Immediately after setting the alarm time, press the AL 1 or AL 2 button repeatedly to cycle through alarm modes:
- Buzzer: Alarm will sound with a buzzer.
- Radio: Alarm will turn on the FM radio to the last tuned station.
- OFF: Alarm is deactivated.
- The corresponding alarm indicator (Alarm 1 or Alarm 2) will light up on the display when an alarm is active.
3. Using the FM Radio
- Press the SOURCE button to switch to FM radio mode. The frequency will appear on the display.
- Manual Tuning: Press the -TUNING+ buttons (< or >) briefly to adjust the frequency step by step.
- Automatic Scan: Press and hold the -TUNING+ buttons (< or >) for a few seconds to automatically scan for the next available station.
- Adjusting Volume: Press the -VOLUME+ buttons (< or >) to increase or decrease the radio volume.
4. Setting Radio Presets (20 Presets)
- Tune to your desired FM station using the tuning buttons.
- Press and hold the PRESET button until the preset number flashes on the display.
- Use the -TUNING+ buttons (< or >) to select the desired preset number (P01-P20).
- Press the PRESET button again to save the station to the selected preset.
- To recall a preset station, briefly press the PRESET button repeatedly to cycle through your saved stations.
5. Snooze Function
When an alarm sounds, press the large SNOOZE button to temporarily silence the alarm for approximately 9 minutes. The alarm will sound again after this period.
6. Stopping the Alarm
To turn off an active alarm for 24 hours, press the corresponding AL 1 or AL 2 button. The alarm indicator will remain lit, and the alarm will sound again at the same time the next day.
To completely deactivate an alarm, follow the steps for "Setting Alarms" and select the "OFF" option.
Maintenance
Cleaning
- Always unplug the clock from the power outlet before cleaning.
- Use a soft, dry cloth to wipe the exterior surfaces of the clock.
- Do not use abrasive cleaners, waxes, or solvents as they may damage the finish.
- Avoid getting moisture into any openings of the device.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power/Display off | Power adapter not connected or outlet is not active. | Ensure the power adapter is securely plugged into the clock and a working wall outlet. |
| Alarm does not sound | Alarm is not set, set to OFF, or volume is too low (for radio alarm). | Verify alarm time and mode (Buzzer/Radio) are correctly set. Increase radio volume if using radio alarm. |
| Radio static or poor reception | Weak signal or interference. | Adjust the position of the clock. Try tuning to a stronger station. |
| Time/Alarm settings lost after power outage | Backup batteries are not installed or are depleted. | Install new AAA backup batteries. |
Specifications
- Brand: Philco
- Model: 1006-GR
- Display Type: 0.6" LED
- Color: Black
- Power Source: Corded Electric (110V/220V compatible)
- Backup Batteries: 2 x AAA (not included)
- Radio: Digital FM Radio with 20 Presets
- Alarm Features: Dual Alarms (Buzzer or Radio)
- Snooze Duration: Approximately 9 minutes
- Product Dimensions: 4.33"W x 4.96"H
- Item Weight: 9.3 ounces
- Material: Acrylonitrile Butadiene Styrene
Warranty and Support
For warranty information or technical support, please refer to the contact details provided on the product packaging or visit the official Philco website. Keep your purchase receipt as proof of purchase for any warranty claims.
Manufacturer: PHILCO
