After a power outage, my ecobee EB-STATE6P-01 Smart Thermostat Premium is heating up and showing an incorrect high temperature, causing the air conditioning to run constantly. Should the lithium batteries be removed, and if so, how do I do that?

Based on the manual for the ecobee EB-STATE6P-01 Smart Thermostat Premium, the main thermostat unit is a hardwired device that operates on 24V power from your HVAC system (via the C-wire). It does not contain user-serviceable lithium batteries that power the main display or temperature sensing logic.If the unit is physically heating up or displaying an incorrect temperature after a power surge or outage, please try the following steps:Power Cycle the Device: Go to your home's circuit breaker panel and turn off the switch for your HVAC/Thermostat. Wait for about 30 seconds and then turn it back on to reboot the internal processor.Check for External Heat Sources: Ensure no new heat sources are near the unit. Sometimes, if the wall behind the thermostat is not sealed, warm air from inside the wall can blow onto the sensor after a system restart.Check the SmartSensor: While the main unit is hardwired, the included SmartSensor (the small white remote sensor) does use a CR2477 lithium coin cell battery. If you are referring to the remote sensor, you can open the back cover to replace or remove the battery, but this will not stop the main wall unit from "heating up."Warning: If the main thermostat unit on the wall is physically hot to the touch, this may indicate an electrical fault caused by the power outage. In this case, you should turn off the power at the breaker immediately and contact ecobee support at ecobee.com/support or consult a qualified HVAC technician, as the internal circuitry may have been damaged by a power surge.

Can I mount the ecobee Smart Thermostat Premium (EB-STATE6P-01) in a furnace room and use a remote SmartSensor for temperature control?

Yes, you can mount the ecobee Smart Thermostat Premium (EB-STATE6P-01) in a furnace room and rely on a SmartSensor for temperature control, but there are several important factors to consider:Sensor Participation: In the ecobee settings (under Comfort Settings), you can choose which sensors participate in each mode (Home, Away, Sleep). You can deselect the thermostat's internal sensor so that it only uses the temperature data from the remote SmartSensor located in your living area.Wi-Fi and Connectivity: The thermostat needs a stable Wi-Fi connection to provide app control and smart features. Ensure your furnace room does not have significant signal interference (like thick concrete walls or metal shielding) that would prevent it from connecting to your router or the remote SmartSensor.Environmental Limits: While the thermostat can be in a furnace room, ensure the room stays within the device's operating temperature and humidity limits. Excessive heat or moisture in a utility room could damage the internal components over time.Accessibility: Remember that the Smart Thermostat Premium includes a built-in air quality monitor and a speaker for voice assistants (like Alexa or Siri). If the unit is hidden in a furnace room, you will lose the ability to use these features effectively.Recommendation: If you proceed with this setup, use the ecobee app to monitor the connection status of your SmartSensor regularly to ensure the thermostat is receiving the correct data from your living space.

ecobee EB-STATE6P-01

ecobee EB-STATE6P-01 Smart Thermostat Premium User Manual

Model: EB-STATE6P-01

Introduction

The ecobee EB-STATE6P-01 Smart Thermostat Premium is an advanced climate control device designed to optimize your home's heating and cooling for comfort and energy efficiency. This manual provides comprehensive instructions for installation, operation, maintenance, and troubleshooting to ensure you get the most out of your smart thermostat.

ecobee Smart Thermostat Premium with SmartSensor

Image: The ecobee Smart Thermostat Premium, a sleek black device with a digital display showing '72', accompanied by a smaller white SmartSensor.

Safety Information

Electrical Safety: Installation involves working with 24-volt electrical wiring. Always turn off power to your HVAC system at the circuit breaker before beginning installation. If you are unsure about wiring, consult a qualified electrician.
Voltage: This device operates on 24 Volts. Ensure your HVAC system is compatible.
Component Handling: Handle all components with care to prevent damage.
Disposal: Dispose of old thermostats and packaging materials responsibly according to local regulations.

What's in the Box

Your ecobee Smart Thermostat Premium package should contain the following items:

ecobee Smart Thermostat Premium unit
SmartSensor for doors and windows (one included)
Mounting plate
Trim plate (optional, for covering marks from old thermostat)
Wire labels
Screws and drywall anchors
Quick Start Guide

Setup

Pre-Installation Checklist

Confirm your HVAC system is compatible with a 24-volt thermostat.
Ensure you have a C-wire (common wire) for continuous power. If not, a Power Extender Kit (PEK) may be required (sold separately or included in some bundles).
Gather necessary tools: Phillips screwdriver, drill (optional), wire strippers (optional).

Installation Steps

Turn off Power: Locate your circuit breaker panel and turn off the power to your heating and cooling system. Verify the power is off by attempting to turn on your old thermostat.
Remove Old Thermostat: Carefully remove the cover of your old thermostat. Take a picture of the wiring before disconnecting any wires. Label each wire with the provided labels.
Mount the ecobee Backplate: Detach the ecobee backplate from the thermostat unit. Feed your wires through the center opening of the backplate. Secure the backplate to the wall using the provided screws and drywall anchors. If needed, use the trim plate to cover any wall imperfections.
Connect Wires: Connect the labeled wires to the corresponding terminals on the ecobee backplate. Refer to the wiring diagram in the Quick Start Guide for specific connections. Ensure wires are securely fastened.
Attach ecobee Thermostat: Align the ecobee thermostat with the mounted backplate and push it firmly until it clicks into place.
Restore Power: Return to your circuit breaker panel and turn the power back on to your HVAC system.

ecobee Smart Thermostat Premium front view

Image: A close-up view of the ecobee Smart Thermostat Premium, showcasing its black, sleek design and digital display.

Initial Configuration

Once powered on, the ecobee thermostat will guide you through the initial setup process on its LCD touch screen. This includes:

Wi-Fi Connection: Connect your thermostat to your home Wi-Fi network. This is essential for smart features and app control.
HVAC System Type: Select your heating and cooling system type (e.g., furnace, heat pump, AC).
SmartSensor Pairing: Follow the on-screen prompts to pair your included SmartSensor.
Account Creation/Login: Create an ecobee account or log in to an existing one via the ecobee app or website to enable remote control and advanced features.

Operating Your ecobee Thermostat

Basic Operation (On-Device)

Adjusting Temperature: Swipe up or down on the LCD touch screen to change the desired temperature.
Changing Modes: Tap the mode icon (e.g., heat, cool, auto, off) to cycle through available operating modes.
Fan Control: Access fan settings to run the fan continuously or on auto.
Menu Navigation: Use the menu icon (three horizontal lines) to access advanced settings and features directly on the thermostat.

ecobee Smart Thermostat Premium with SmartSensor from another angle

Image: The ecobee Smart Thermostat Premium and its accompanying SmartSensor, viewed from a slight angle, highlighting their compact design.

Advanced Features and App Control

Auto-Scheduling: The ecobee thermostat features auto-scheduling capabilities, learning your habits and adjusting temperatures accordingly for optimal comfort and energy savings. You can also create custom schedules.
Smart Home Integration: This thermostat is compatible with Apple HomeKit, Google Assistant, SmartThings, and Amazon Alexa. Link your ecobee account to these platforms for voice control and integrated smart home routines.
Remote Control via App: Download the ecobee app on your smartphone or tablet. The app allows you to:
- Adjust temperature from anywhere.
- Create and modify schedules.
- Monitor energy usage reports.
- Receive alerts and reminders.
- Manage multiple ecobee devices and SmartSensors.
SmartSensor Utilization: Place SmartSensors in frequently used rooms to detect occupancy and temperature, helping the thermostat deliver comfort where it matters most.

Maintenance

Cleaning the Thermostat: Gently wipe the LCD touch screen and the body of the thermostat with a soft, damp cloth. Avoid abrasive cleaners or solvents.
SmartSensor Care: Ensure SmartSensors are kept clean and free from obstructions to maintain accurate readings.
Firmware Updates: Your ecobee thermostat will automatically download and install firmware updates when connected to Wi-Fi. Ensure your thermostat remains connected to receive the latest features and improvements.

Troubleshooting

Problem	Possible Cause	Solution
Thermostat not powering on.	No power from HVAC system; C-wire issue; incorrect wiring.	Check circuit breaker. Verify C-wire connection. Re-check all wiring connections.
Cannot connect to Wi-Fi.	Incorrect Wi-Fi password; router issues; thermostat too far from router.	Double-check Wi-Fi password. Restart your router. Ensure thermostat is within Wi-Fi range.
HVAC system not responding.	Incorrect system type selected; wiring issue; HVAC system fault.	Verify HVAC system type in settings. Check wiring connections. Consult an HVAC professional if issues persist.
SmartSensor not pairing.	Sensor out of range; battery low; interference.	Move sensor closer to thermostat. Replace sensor battery. Remove potential sources of interference.

For more detailed troubleshooting or error codes, refer to the ecobee support website or contact customer service.

Specifications

Model: EB-STATE6P-01
Brand: ecobee
Color: Black
Display Type: LCD Touch Screen
Power Source: Hardwired Electric
Voltage: 24 Volts
Connectivity Technology: Low-Voltage, Wi-Fi
Control Type: Button Control, Voice
Controller Compatibility: Apple HomeKit, Google Assistant, SmartThings, Amazon Alexa
Special Feature: Auto-Scheduling
Included Components: Temperature Sensor, SmartSensor for doors and windows
Mounting Type: Wall Mount
Item Weight: Approximately 1.34 pounds (0.61 Kilograms)
Package Dimensions: 6.97 x 6.1 x 2.91 inches

Warranty and Support

For detailed warranty information, please refer to the warranty card included with your product or visit the official ecobee website. ecobee products typically come with a limited warranty covering defects in materials and workmanship.

If you encounter any issues or require technical assistance, please contact ecobee customer support:

Online Support: Visit ecobee.com/support
Phone Support: Refer to the ecobee website for current contact numbers and operating hours.

Please have your product model number (EB-STATE6P-01) and proof of purchase ready when contacting support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.