Introduction
The Insta360 Pivot Stand is a versatile accessory designed for the Insta360 GO 3 camera and Action Pod. It features a reusable sticky base for mounting on various surfaces and a magnetic latch system for secure attachment. The adjustable ball joint allows for flexible shooting angles, enhancing creative possibilities. This manual provides detailed instructions for the proper use and maintenance of your Pivot Stand.
Product Overview
The Pivot Stand is engineered for quick and secure mounting of your Insta360 GO 3 camera or Action Pod. Its compact design and robust magnetic connection ensure stability while providing extensive adjustability.
What's in the Box
- 1x Pivot Stand
Key Features
- Mount Anywhere: Features a reusable sticky base for versatile mounting on various surfaces.
- Magnetic Latch: Securely mounts both your GO 3 camera and the Action Pod.
- Adjustable Ball Joint: Provides flexible shooting and creative angles.
- Universal Mounting: Includes a 1/4'' mounting point for compatibility with other accessories.
Figure 1: The Insta360 Pivot Stand with the GO 3 camera securely attached, showcasing its compact design.
Setup
Follow these steps to set up your Insta360 Pivot Stand and attach your camera:
- Prepare the Surface: Ensure the surface where you intend to mount the Pivot Stand is clean, dry, and smooth for optimal adhesion of the sticky base.
- Attach the Camera/Action Pod: Align the magnetic base of your Insta360 GO 3 camera or Action Pod with the magnetic latch on the Pivot Stand. The strong magnets will snap into place, and the fixed claw latch will secure it. Ensure the camera lens is facing the direction indicated by the small camera icon on the stand.
- Secure the Stand: Press the sticky base of the Pivot Stand firmly onto your desired surface. For best results, apply pressure for a few seconds to ensure a strong bond.
Figure 2: Attaching the GO 3 camera to the Pivot Stand's magnetic latch system.
Operating Instructions
The Pivot Stand offers flexibility for various shooting scenarios:
Adjusting Angles
The integrated ball joint allows for 180-degree tilt and 360-degree rotation. Simply hold the base of the stand and gently adjust the camera to your desired angle. The joint is designed to hold its position securely.
Figure 3: Illustrates the adjustable ball joint, allowing for 180-degree tilt and 360-degree rotation for flexible camera positioning.
Mounting Options
- Sticky Base: Ideal for smooth, flat surfaces like dashboards, tables, or walls. The base is reusable after cleaning.
- 1/4'' Screw Point: The bottom of the stand features a universal 1/4'' screw thread, allowing it to be mounted on tripods, selfie sticks, or other camera accessories.
Figure 4: Examples of diverse mounting possibilities with the Pivot Stand, from vehicle interiors to musical instruments and overhead surfaces.
Removing the Camera/Action Pod
To detach the camera or Action Pod, simply press the two release buttons on the sides of the magnetic latch and pull the camera away from the stand.
Figure 5: The magnetic latch ensures a secure connection for both the GO 3 camera and its Action Pod.
Maintenance
Proper maintenance ensures the longevity and performance of your Pivot Stand:
- Cleaning the Sticky Base: If the sticky base loses adhesion, gently wash it with clean water and let it air dry completely. Avoid using harsh chemicals or abrasive materials, as this can damage the adhesive.
- Storage: When not in use, flip the protective cover over the sticky base to protect it from dirt and dust. This maintains the adhesive's effectiveness for future use.
- General Cleaning: Wipe the stand with a soft, damp cloth to remove any dust or smudges.
Figure 6: Proper storage of the Pivot Stand with the protective cover flipped over the sticky base to prevent dust accumulation.
Troubleshooting
If you encounter issues with your Pivot Stand, refer to the following common solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Sticky base not adhering well. | Dust, dirt, or oil on the adhesive surface or mounting surface. | Wash the sticky base with clean water and let it air dry completely. Ensure the mounting surface is clean and dry. |
| Camera/Action Pod feels loose on the magnetic latch. | Improper alignment or debris on magnetic contacts. | Ensure the camera/Action Pod is correctly aligned with the stand's magnetic latch. Check for any obstructions on the magnetic surfaces and clean if necessary. |
| Ball joint is too stiff or too loose. | Normal wear or environmental factors. | The ball joint is designed to maintain tension. If it becomes excessively loose over time, contact Insta360 support. Avoid forcing the joint if it feels too stiff. |
Specifications
| Attribute | Detail |
|---|---|
| Materials | Nano adhesive, TPU, stainless steel |
| Weight | 3.52 ounces (approx. 100g) |
| Dimensions (L x W x H) | 4.7 x 3.1 x 1.8 inches (approx. 11.9 x 7.9 x 4.6 cm) |
| Model Number | CINSBBKC |
| Mounting Type | Table / Adhesive |
| Compatible Devices | Insta360 GO 3 Camera, Insta360 GO 3 Action Pod |
Warranty and Support
Insta360 products typically come with a standard manufacturer's warranty. For specific warranty details, registration, or technical support, please visit the official Insta360 website or contact their customer service directly.
Official Insta360 Website: www.insta360.com
