DONGKER MDS-60

Download PDF
Contents

DONGKER MDS-60 DIY Metal Detector Kit Instruction Manual

Model: MDS-60

1. Introduction

The DONGKER MDS-60 is a high-performance DIY metal detector kit designed for security applications and educational electronic soldering practice. This kit provides an accessible way to assemble a functional metal detector module. It is characterized by its high reliability, good stability, and compact size, making it suitable for various projects and learning experiences.

Assembled DONGKER MDS-60 DIY Metal Detector Kit

Image 1.1: Assembled DONGKER MDS-60 DIY Metal Detector Kit, showing the green PCB with a circular coil and various electronic components.

2. Specifications

The DONGKER MDS-60 Metal Detector Kit features the following technical specifications:

ParameterValue
Operating VoltageDC 3-5V
Operating CurrentLess than or equal to 40mA
Standby Current5mA
Detection DistanceUp to 60mm
Alarm ModeSound / Light (LED)
Assembly DifficultyEasy
PCB Size86mm x 61mm
Item Weight (Kit)Approximately 3.52 ounces (100g)
Table of parameters and component list for the MDS-60 kit

Image 2.1: Detailed table showing the parameters and component list for the MDS-60 kit, essential for assembly and understanding the module's capabilities.

3. Package Contents

The DONGKER MDS-60 DIY Metal Detector Kit includes all necessary electronic components for assembly. Please verify that all parts listed below are present before beginning assembly.

No.NameParameterQuantity
R3Resistor470R1
R2Resistor2K1
R1Resistor200K1
VR1Adjustable Resistor100R1
C2, C3Ceramic Capacitor222P2
C1, C4Ceramic Capacitor104P2
C5Electrolytic Capacitor100UF1
LED1LED5mm Red1
Q2, Q3Transistor (Triode)S90122
Q1Transistor (Triode)S90181
SW1Power Switch6P 6*51
SP1Buzzer9*121
J1Power SocketKF301-21
—PCBMDS-601
OptionalBattery BoxAA1.5V*31
DONGKER MDS-60 DIY Metal Detector Kit components laid out

Image 3.1: All individual components of the MDS-60 DIY Metal Detector Kit laid out, including the PCB, resistors, capacitors, transistors, LED, buzzer, switch, and power socket.

4. Assembly Instructions

This kit requires soldering. Basic soldering skills are recommended. Please follow the component list and PCB markings carefully.

4.1 Required Tools (Not Included)

  • Electric Soldering Iron
  • Soldering Iron Holder
  • Solder Wire
  • Solder Sucker (for desoldering)
  • Tweezers
  • Diagonal Cutting Pliers
  • Sharp-nose Pliers
  • Screwdriver (various sizes)
  • Multimeter (for testing)
  • Sponge (for cleaning soldering iron tip)

4.2 Assembly Steps

  1. Identify Components: Carefully identify each component using the provided component list (Image 2.1) and the markings on the PCB (Image 4.1). Pay attention to resistor values, capacitor polarities (for electrolytic capacitor C5), and transistor types (S9012, S9018).
  2. Solder Resistors: Start by soldering the resistors (R1, R2, R3, VR1) into their designated positions on the PCB. Resistors are not polarized.
  3. Solder Capacitors: Solder the ceramic capacitors (C1, C2, C3, C4). These are not polarized. For the electrolytic capacitor (C5), ensure correct polarity; the longer lead is typically positive (+), and the shorter lead or marked side is negative (-). Match this with the PCB markings.
  4. Solder Transistors: Solder the transistors (Q1, Q2, Q3). Ensure their flat side or pin configuration matches the outline on the PCB.
  5. Solder LED: Solder the LED (LED1). LEDs are polarized; the longer lead is positive (+), and the shorter lead is negative (-). Match with PCB markings.
  6. Solder Buzzer: Solder the buzzer (SP1). Some buzzers are polarized; check for markings on the buzzer and PCB.
  7. Solder Power Switch and Socket: Solder the power switch (SW1) and the power socket (J1) into their respective positions.
  8. Inspect Solder Joints: After soldering all components, carefully inspect all solder joints for cold joints, bridges, or poor connections. Ensure all components are securely attached and correctly oriented.
Top view of the MDS-60 PCB with component outlines

Image 4.1: Top view of the MDS-60 Printed Circuit Board (PCB), showing component placement outlines and labels for assembly reference.

Bottom view of the MDS-60 PCB showing solder pads

Image 4.2: Bottom view of the MDS-60 PCB, illustrating the solder pads and traces for component connections.

5. Setup and Wiring

Once the kit is fully assembled, connect a DC power source to the module.

5.1 Power Connection

  • The module requires a DC power input between 3V and 5V.
  • Connect the positive (+) terminal of your power supply to the `+DC3-5V` terminal on the module's power socket (J1).
  • Connect the negative (-) terminal (ground) of your power supply to the `-` terminal on the module's power socket (J1).
  • An optional battery box for 3x AA 1.5V batteries (total 4.5V) can be used as a portable power source.
Close-up of the assembled MDS-60 board showing power input terminals

Image 5.1: Close-up view of the assembled MDS-60 module, highlighting the power input terminals (+DC3-5V-) and the power switch (SW1).

6. Operation

After successful assembly and power connection, the metal detector is ready for operation.

6.1 Power On

Toggle the power switch (SW1) to the 'ON' position. The LED (LED1) may illuminate briefly, and the buzzer (SP1) might emit a short sound as the circuit stabilizes.

6.2 Sensitivity Adjustment

The module features an adjustable resistor (VR1) which can be used to fine-tune the detection sensitivity. Use a small screwdriver to carefully turn VR1. Adjusting this potentiometer will change the detection range and the threshold at which the alarm activates.

6.3 Metal Detection

Move the circular coil part of the module near metallic objects. When a metal object is detected within the 60mm range, the LED (LED1) will light up, and the buzzer (SP1) will emit an audible alarm.

7. Applications

The DONGKER MDS-60 DIY Metal Detector Kit can be utilized in various educational and practical scenarios:

  • Game entertainment projects
  • Basic security checks
  • Searching for small metal products
  • Car detection systems
  • Traffic statistics applications
  • Elevator floor control systems
  • Production equipment position detection
  • Development and design of production equipment
  • Electronic product design projects
  • Development of play equipment
  • Metal proximity switch applications
  • Basic metal detection in human body (e.g., for educational purposes)

8. Troubleshooting

If the metal detector does not function as expected, consider the following:

  • No Power/No Indication:
    • Check power supply connections and ensure the voltage is within DC 3-5V.
    • Verify the power switch (SW1) is in the 'ON' position.
    • Inspect all solder joints for continuity and proper connection using a multimeter.
    • Ensure the LED (LED1) is correctly oriented and not damaged.
  • No Detection/Constant Alarm:
    • Adjust the sensitivity potentiometer (VR1) to calibrate the detection threshold.
    • Ensure all components, especially transistors and capacitors, are correctly oriented and not damaged.
    • Check for any short circuits or open circuits on the PCB.
  • Weak Detection:
    • Increase the sensitivity by adjusting VR1.
    • Ensure the power supply is stable and providing adequate current.

9. Maintenance

To ensure the longevity and proper functioning of your DONGKER MDS-60 module:

  • Keep the module clean and free from dust and debris.
  • Avoid exposing the module to moisture or extreme temperatures.
  • Handle the PCB and components with care to prevent physical damage.
  • Store in a dry, cool environment when not in use.

10. Support

For further assistance or inquiries regarding the DONGKER MDS-60 DIY Metal Detector Kit, please refer to the seller or manufacturer's official support channels.

© 2023 DONGKER. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.