SUPPLYZ Replacement Wall Oven Door Seal

1. Introduction

This manual provides instructions for the installation and maintenance of the SUPPLYZ WP701650 replacement wall oven door seal. This product is designed as a direct replacement for the original oven door seal in compatible Whirlpool wall oven models, ensuring proper heat retention and efficient oven operation.

2. Safety Information

• Disconnect Power: Always disconnect the electrical power to the oven at the circuit breaker or fuse box before attempting any installation or maintenance. Failure to do so can result in electric shock or serious injury.
• Wear Protective Gear: It is recommended to wear work gloves to protect your hands from sharp edges or hot surfaces.
• Allow Cooling: Ensure the oven is completely cool before beginning any work to prevent burns.
• Professional Assistance: If you are unsure about any step of the installation process, consult a qualified appliance technician.

3. Package Contents

Your package should contain the following item:

• One (1) SUPPLYZ WP701650 Wall Oven Door Seal

4. Compatibility

This replacement door seal is compatible with various Whirlpool wall oven models. It replaces part numbers 701650, 34-5-80288, 580288, 7-1650, AH2076316, EA2076316, JA99701650, and PS2076316.

Known compatible models include, but are not limited to:

• 21238, 21239, 21336, 629.21138
• BEV7110, CCE700, CCE701, CWE1000, CWE600, CWE601, CWE602, CWE6020ACB, CWE700, CWE701, CWE9900
• GCCE701, LCCE700, LCCE701
• W104, W105, W105-C, W106B, W106W, W106W-C, W121, W121-C, W121-E, W122, W122-C, W123, W123-C, W136, W136-C, W136W, W136W-C, W141, W141-C, W142, W142-C, W146, W146-C, W156-C, W156B, W156B-C, W156W, W156W-C, W181, W188, W188W, W188W-C, W198, W198-C, W198W, W198W-C
• W204, W205, W206B, W206B-C, W206W, W206W-C, W211, W214, W215, W221, W221-C, W224, W225, W227B, W227W, W230, W231, W236, W236B, W236W, W241, W241-C, W2410B, W242, W2450B, W2450W, W2451B, W2451W, W246, W246-C, W246W, W256, W256B, W256B-C, W256W, W256W-C, W266, W276, W276W
• WM227B, WM236B, WW2460B, WW2460W

Always verify compatibility with your specific oven model before installation.

5. Installation Instructions

This section outlines the general steps for replacing a wall oven door seal. Specific oven designs may vary slightly.

Tools Required:

• Work Gloves
• Flathead Screwdriver (potentially for prying clips)
• Cleaning Cloth

Procedure:

1. Disconnect Power: Locate your oven's circuit breaker and turn off the power supply to the appliance. Confirm the power is off by attempting to turn on the oven.
2. Open Oven Door: Fully open the oven door to access the existing door seal.
3. Inspect Old Seal: Observe how the old seal is attached. Most oven door seals are held in place by clips or hooks that fit into small holes around the oven frame.
4. Remove Old Seal: Carefully pull the old seal away from the oven frame. If it's secured by clips, gently pry them out of their holes. Work your way around the entire perimeter until the old seal is completely removed.
5. Clean Mounting Area: Use a cleaning cloth to wipe down the area where the seal mounts. Remove any food debris, grease, or residue to ensure a clean surface for the new seal.
6. Install New Seal: Begin by aligning the new SUPPLYZ WP701650 door seal with the mounting holes or slots on the oven frame. Start at one corner or a designated starting point (often indicated by a seam or specific hook). Press the clips or hooks of the new seal firmly into the corresponding holes. Work your way around the entire oven door frame, ensuring the seal is seated correctly and securely. The seal should fit snugly without any gaps or loose sections.

Image 1: SUPPLYZ WP701650 Replacement Wall Oven Door Seal. A rectangular, flexible oven door seal, made of braided metallic material, designed to fit around the perimeter of a wall oven door. The seal features a gap at the bottom, indicating where the ends meet or attach.

7. Close Oven Door: Gently close the oven door and check for a proper seal. The door should close completely and feel secure.
8. Reconnect Power: Restore power to the oven at the circuit breaker.
9. Test Oven: Turn on the oven to a low temperature and observe if any heat is escaping around the door. A properly installed seal will prevent heat loss.

6. Maintenance

To ensure the longevity and effectiveness of your oven door seal:

• Regular Inspection: Periodically inspect the seal for any signs of wear, tears, hardening, or damage.
• Cleaning: Gently wipe the seal with a damp cloth and mild detergent to remove food spills or grease. Avoid harsh chemicals or abrasive cleaners, as these can damage the seal material.
• Avoid Pinching: Be careful not to pinch or snag the seal when closing the oven door or placing items in the oven.

7. Troubleshooting

• Oven Leaking Heat: If you notice heat escaping from around the oven door after installation, ensure the seal is fully seated in all mounting points. Re-open the door and carefully press the seal into place along the entire perimeter.
• Door Not Closing Properly: Check if the seal is twisted or improperly installed, creating an obstruction. Remove and re-install the seal, ensuring it lies flat and is not bunched up.
• Seal Appears Damaged: If the seal arrives damaged or becomes damaged shortly after installation, contact the seller for assistance.

8. Specifications

9. Warranty and Support

As a direct replacement part, specific warranty details may vary. Please refer to the seller, SUPPLYZ-OEM, for information regarding product warranty, returns, or technical support. Contact information for the seller can typically be found on your purchase receipt or the platform where the product was acquired.