FIREGAS Chimney Cooker Hood 60 cm (Model FGS-ESD17Z60CC) User Manual

1. Introduction

This manual provides essential information for the safe installation, operation, and maintenance of your FIREGAS Chimney Cooker Hood, Model FGS-ESD17Z60CC. Please read these instructions carefully before using the appliance and retain them for future reference.

The FIREGAS Chimney Cooker Hood is designed to efficiently remove smoke, steam, odors, and grease that occur when using hobs, ensuring a fresh cooking environment. It features a powerful suction rate, energy-efficient design, and user-friendly touch controls.

Figure 1.1: FIREGAS Chimney Cooker Hood, Model FGS-ESD17Z60CC.

1.1 Safety Information

• Ensure the appliance is installed by a qualified person in accordance with local regulations.
• Always disconnect the power supply before cleaning or performing maintenance.
• Do not flambé under the cooker hood.
• Ensure adequate ventilation in the room when the cooker hood is used simultaneously with gas or other fuel-burning appliances.
• Regularly clean grease filters to prevent fire hazards.
• Keep children away from the appliance during operation and cleaning.

2. Setup and Installation

The FIREGAS Chimney Cooker Hood is designed for wall-mounted installation. It supports both extraction (ducting) and recirculation modes. Ensure you have all necessary components before beginning installation.

2.1 Package Contents

Verify that all items are present in the package:

• Chimney Cooker Hood unit
• Grease filters (5-layer)
• Carbon Filters (Model No.: CC 130) - for recirculation mode
• Dampers
• Duct Pipe
• Air Outlet
• Chimney fixing bracket
• Screws and wall plugs
• Instruction Manual

Figure 2.1: Included components in the package.

2.2 Installation Modes

The cooker hood can be installed in two modes:

• Extraction Mode (Ducting): Air is extracted from the kitchen and vented outside through a duct pipe. This mode requires an external vent.
• Recirculation Mode: Air is filtered through carbon filters to remove odors and then recirculated back into the kitchen. This mode is suitable when external venting is not possible. Carbon filters are required for this mode.

Figure 2.2: Illustration of Extraction and Recirculation Modes.

2.3 Mounting Dimensions

Refer to the diagram below for critical dimensions and mounting points. Ensure sufficient clearance above the cooking surface as per local building codes and manufacturer recommendations (typically 65-75 cm for electric hobs and 75-85 cm for gas hobs).

Figure 2.3: Product Dimensions and Mounting Details.

3. Operation

The FIREGAS Chimney Cooker Hood features an intuitive touch control panel for easy operation of its functions.

3.1 Control Panel Overview

Figure 3.1: Touch Control Panel.

• Power Button: Turns the hood on or off.
• Fan Speed Control (-/+): Adjusts the fan speed. There are 3 available speeds to suit different cooking needs.
• Light Button: Controls the integrated LED lighting.
• Timer/Delay-off Function: Activates a delayed shut-off, allowing the hood to continue operating for a set period after cooking is finished.

3.2 Fan Speed Settings

The cooker hood offers three fan speeds:

• Speed 1 (Low): Ideal for simmering or light cooking (120 m³/h).
• Speed 2 (Medium): Suitable for general cooking and moderate steam/odor.
• Speed 3 (High): For heavy frying, grilling, or when strong odors are present. Provides a powerful suction rate of 335 m³/h.

Figure 3.2: Powerful Airflow for Efficient Extraction.

3.3 LED Lighting

The hood is equipped with two 1.5-watt energy-saving LED lights, providing bright illumination for your cooking area. Press the light button on the control panel to turn the lights on or off.

Figure 3.3: Integrated LED Lighting.

4. Maintenance

Regular cleaning and maintenance ensure optimal performance and extend the lifespan of your cooker hood. Always disconnect the power supply before cleaning.

4.1 Cleaning the Exterior

Wipe the exterior surfaces with a soft cloth dampened with mild detergent. Do not use abrasive cleaners, corrosive detergents, or stiff brushes, as these can damage the stainless steel finish.

4.2 Cleaning Grease Filters

The 5-layer metal grease filters capture grease particles from cooking fumes. They should be cleaned regularly (approximately every 2-4 weeks, depending on usage) to maintain efficiency and prevent fire hazards.

1. Remove the grease filters by releasing their latches.
2. Wash the filters by hand in hot soapy water or in a dishwasher. Ensure they are completely dry before re-installing.
3. Re-install the clean, dry grease filters.

Figure 4.1: Cleaning the 5-Layer Grease Filters.

4.3 Replacing Carbon Filters (Recirculation Mode Only)

If your hood is operating in recirculation mode, the carbon filters (Model No.: CC 130) absorb odors. These filters cannot be washed and must be replaced approximately every 3-6 months, depending on usage.

1. Remove the grease filters to access the carbon filters.
2. Twist or unclip the old carbon filters and remove them.
3. Install new carbon filters, ensuring they are securely in place.
4. Re-install the grease filters.

5. Troubleshooting

Before contacting customer support, please refer to the following table for common issues and their potential solutions.

6. Specifications

Technical specifications for the FIREGAS Chimney Cooker Hood, Model FGS-ESD17Z60CC.

Figure 6.1: Product Data Sheet (Original in Dutch).

7. Warranty and Support

For warranty information, technical support, or service requests, please refer to the warranty card included with your product or contact FIREGAS customer service. Keep your purchase receipt as proof of purchase.

For further assistance, please visit the official FIREGAS website or contact your retailer.