1. Introduction
Thank you for choosing the Teleflex Premier Pro Black 65 MPH Boat Speedometer. This instrument is designed for marine applications, providing accurate speed readings up to 65 MPH. This manual will guide you through the proper installation, operation, and care of your new speedometer.
1.1 Package Contents
- Teleflex Premier Pro Black 65 MPH Speedometer (Part Number: 84513)
- Mounting Bracket
Note: Hardware and a detailed installation manual are not included with the product as supplied by some retailers. This document serves as a general guide.
2. Safety Information
Always observe the following safety precautions during installation and operation:
- Ensure the boat's power is disconnected before beginning any installation work to prevent electrical shock.
- Wear appropriate personal protective equipment, such as safety glasses and gloves.
- Verify all connections are secure and properly insulated to prevent short circuits.
- Consult a qualified marine technician if you are unsure about any part of the installation process.
3. Setup and Installation
3.1 Pre-Installation Check
Before installation, ensure you have the necessary tools and that the mounting location is suitable. The speedometer requires an approximate 3 1/4 inch (8.26 cm) diameter cutout.
3.2 Mounting Instructions
- Identify a suitable location on your boat's dashboard or panel for the speedometer.
- Using a hole saw, create a 3 1/4 inch (8.26 cm) diameter cutout at the chosen location.
- Insert the speedometer into the cutout from the front of the panel.
- Secure the speedometer using the provided mounting bracket on the rear of the panel. Tighten the nuts evenly until the gauge is firmly in place.
Figure 1: Front view of the Teleflex Premier Pro Black 65 MPH Speedometer. It features a black face, white needle, and blue and white graphics, with a domed lens and black bezel.
3.3 Electrical and Pitot Connections
The speedometer has (2) male spade terminals for electrical connections and (1) pitot connection for speed sensing.
- Connect the positive (+) 12V DC power wire to one of the male spade terminals.
- Connect the negative (-) ground wire to the other male spade terminal.
- Connect the pitot tube from your boat's pitot pickup to the pitot connection on the back of the speedometer. Ensure the tube is free of kinks and blockages.
Figure 2: Rear view of the speedometer, showing the two male spade terminals for electrical connections and the pitot connection for the speed sensing tube. A mounting bracket is also visible.
4. Operating Instructions
4.1 Basic Operation
Once properly installed and connected, the speedometer will display your boat's speed in miles per hour (MPH) as water flows through the pitot tube. The gauge is halogen-illuminated for visibility in various lighting conditions.
- Turn on your boat's ignition or accessory power to activate the speedometer.
- As the boat moves through the water, the pitot tube will sense the water pressure, which is then translated into a speed reading on the gauge.
- The white needle indicates the current speed, while the blue and white graphics provide clear numerical readings.
4.2 Pitot System Functionality
The speedometer relies on a pitot tube system, which measures dynamic pressure created by the boat's movement through water. This pressure is transmitted via a hose to the speedometer, where it moves a diaphragm connected to the needle mechanism. Ensure your pitot tube is clear of debris and properly positioned for accurate readings.
5. Maintenance
5.1 Cleaning and Care
To maintain the appearance and functionality of your speedometer:
- Clean the gauge face and bezel with a soft, damp cloth. Avoid abrasive cleaners or solvents.
- Periodically check the pitot tube for blockages (e.g., marine growth, debris) and clear them as necessary.
- Inspect electrical connections for corrosion or looseness and address them promptly.
6. Troubleshooting
If you experience issues with your speedometer, refer to the table below:
| Problem | Possible Cause | Solution |
|---|---|---|
| Speedometer not working | No power; Loose electrical connection; Blocked pitot tube | Check power supply; Secure connections; Clear pitot tube |
| Inaccurate speed reading | Partially blocked pitot tube; Damaged pitot tube; Incorrect pitot tube angle | Clear pitot tube; Inspect and replace if damaged; Adjust pitot tube angle |
| No illumination | Faulty bulb; No power to illumination circuit | Check bulb and replace if necessary; Verify illumination wiring |
7. Specifications
Key technical specifications for the Teleflex Premier Pro Black 65 MPH Speedometer:
| Feature | Specification |
|---|---|
| Part Manufacturer | Teleflex |
| Series | Premier Pro Black |
| Part Number | 84513 |
| Color | Black |
| Cutout Dimensions | 3 1/4" Dia. (8.26 cm) |
| Overall Dimensions | 3 3/4" Dia. (9.53 cm) x 3 1/4" D (8.26 cm) |
| Connections | Pitot, (2) Male Spades |
| Material | Black metal, plastic or glass |
| Item Weight | 1 Pound (0.45 kg) |
8. Warranty and Support
8.1 Warranty Information
This product is sold as seen in pictures, and specific warranty information is not provided with the retail package. For details regarding manufacturer's warranty, please contact Teleflex directly or the authorized dealer from whom you purchased the product.
8.2 Customer Support
For technical assistance or further inquiries, please reach out to the manufacturer or your product supplier. Always provide the model number (84513) and part number when seeking support.
