Introduction
Thank you for choosing TEKSHINNY Flexible Dual Color LED Headlight Strips. These 24-inch (61 cm) strips are designed to enhance vehicle visibility and aesthetics, functioning as both daytime running lights (DRL) and sequential turn signals. This manual provides essential information for proper installation, operation, and maintenance to ensure optimal performance and longevity of your product.
Safety Information
- Always disconnect the vehicle's battery before performing any electrical work to prevent electrical shock or damage.
- Ensure all connections are secure and properly insulated to prevent short circuits.
- Do not modify the product in ways not described in this manual. Unauthorized modifications may void the warranty and create safety hazards.
- Consult a professional automotive electrician if you are unsure about any installation steps.
- Ensure the installed lights do not obstruct the driver's view or violate local traffic laws.
Setup and Installation
The TEKSHINNY LED strips are designed for easy installation without requiring headlight assembly disassembly. Follow these steps carefully:
- Prepare the Surface: Clean the installation area on your vehicle's headlight surface thoroughly. Ensure it is dry and free of dust, grease, or wax.
- Identify Left and Right: Confirm the correct orientation for the left (L) and right (R) strips.
- Apply Adhesive: Carefully peel off the protective film from the strong 3M adhesive tape on the back of the LED strip.
- Position and Stick: Firmly press the LED strip onto the desired location on your car's headlight assembly. Ensure a secure bond.
- Wire Connection: Connect the wires as follows:
- Red Wire: Connect to ACC (+) (Accessory power, typically 12V, which turns on with the ignition).
- Yellow Wire: Connect to the turn signal wire. This will activate the sequential yellow light.
- Black Wire: Connect to the negative pole of the battery (-) or a suitable ground point on the vehicle chassis.
- Test Functionality: After connecting, test both the daytime running light (DRL) and turn signal functions to ensure they operate correctly.
Image: Step-by-step installation process showing identification of left/right, peeling tape, sticking to car, and wiring connections.
Image: Visual representation of the LED strip's dimensions (600mm/23.62in length, 16mm/0.63in width, 4mm/0.16in thickness) and features like dustproof, waterproof, flexibility, and strong adhesion.
Image: Close-up of the three-wire connection: Red to ACC(+), Yellow to turn signal, Black to negative pole of battery(-).
Operating Instructions
These LED strips offer dual-color functionality for enhanced vehicle signaling and visibility.
- Daytime Running Light (DRL): When the vehicle's ignition is on and the turn signal is not active, the LED strips will illuminate in a steady red color, providing increased visibility during daylight hours.
- Turn Signal Light: When the turn signal is activated, the red DRL will switch to a sequential yellow light, clearly indicating your turning intention to other drivers. The yellow light will flash sequentially from one end to the other.
Image: A car displaying the red daytime running light function of the LED strips.
Image: A car displaying the yellow sequential turn signal light function of the LED strips.
Image: The LED strip submerged in water, illustrating its IP68 waterproof rating, alongside cars driving in foggy, rainy, overcast, and snowy conditions, demonstrating its reliability in diverse weather.
Maintenance
- Cleaning: Clean the LED strips periodically with a soft, damp cloth to remove dirt and debris. Avoid using harsh chemicals or abrasive cleaners.
- Inspection: Regularly inspect the strips and wiring for any signs of damage, wear, or loose connections.
- Cutting Instructions: If shortening the strips is necessary, they can be cut every 3 LED beads. After cutting, it is crucial to seal the cut end with insulating glue to maintain the waterproof integrity of the strip. Failure to do so will compromise its IP68 rating.
Image: A pair of scissors cutting the flexible LED strip, illustrating the point where it can be trimmed.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| LED strip does not light up. | No power, loose connection, incorrect wiring, damaged strip. | Check power source (ACC), ensure all wires are securely connected and correctly wired (Red to ACC+, Black to Ground). Inspect the strip for visible damage. |
| Turn signal function not working or not sequential. | Yellow wire not connected to turn signal, incorrect turn signal wiring. | Verify the yellow wire is correctly connected to the vehicle's turn signal circuit. Ensure the turn signal circuit provides the correct signal type. |
| Lights flicker or are dim. | Insufficient power, loose connection, faulty wiring. | Check voltage supply to the red wire. Tighten all connections. Inspect wiring for corrosion or damage. |
| Water ingress after cutting. | Cut end not properly sealed. | Ensure the cut end is sealed with insulating glue to restore waterproof protection. |
Specifications
- Brand: TEKSHINNY
- Model Number: RXD-RED
- Color: Red/Yellow
- Length: 24 inches (61 cm)
- Voltage: 12 Volts
- Light Source Type: LED
- Form Factor: Strip
- Water Resistance Level: IP68 (Waterproof)
- Material: Silicone Plastic
- Number of Pieces: 2
- Connectivity Technology: Bluetooth (Note: This model does not include a remote control, Bluetooth functionality may refer to other product variants or general brand features.)
- Special Features: Multicolor (Red DRL, Sequential Yellow Turn Signal)
- Compatible Vehicle Type: Truck, Car, SUV
- Components Included: 2 LED strips and a driver
Warranty and Support
TEKSHINNY products are designed for quality and durability. For specific warranty details, please refer to the purchase documentation or contact your retailer. In case of any issues or questions regarding your product, please reach out to TEKSHINNY customer support.
Return Policy: This product typically includes a 30-day return policy from the date of purchase. Please check with your seller for specific return conditions.