VINZ Vigo Full-Face Motorcycle Helmet User Manual

1. Introduction

Thank you for choosing the VINZ Vigo Full-Face Motorcycle Helmet. This manual provides essential information for the proper use, maintenance, and care of your helmet. Please read this manual thoroughly before using your helmet to ensure maximum safety and extend the product's lifespan.

The VINZ Vigo helmet is designed to offer superior protection and comfort for motorcyclists, scooter riders, and moped users. It features a high-quality ABS outer shell and a clear, anti-scratch visor, meeting stringent safety standards.

2. Safety Information

Your VINZ Vigo helmet is certified according to ECE 22.06 standards, ensuring it meets the highest European safety requirements for motorcycle helmets. Always ensure the helmet fits correctly and the chin strap is securely fastened before riding.

Important Safety Warnings:

• Always wear a helmet when operating a motorcycle, scooter, or moped.
• Ensure the helmet is the correct size and fits snugly. A loose helmet can compromise safety.
• Never modify your helmet. Any alteration can weaken its protective capabilities.
• Do not use harsh chemicals or solvents for cleaning, as they can damage the helmet's materials.
• Replace your helmet after any impact, even if visible damage is not apparent. Internal damage may exist.

Figure 2.1: Proper helmet fit is crucial for safety. The helmet should sit level on the head and not move freely.

3. Product Features

• ECE 22.06 Certified: Meets stringent European safety standards.
• High-Quality ABS Shell: Provides maximum protection and durability.
• Clear, Anti-Scratch Visor: Ensures clear vision and resistance to minor abrasions.
• Comfortable Interior Padding: Soft-touch lining for enhanced comfort during long rides.
• Removable and Washable Ear Pads: Allows for easy cleaning and hygiene, especially in warm weather.
• Ratchet Closure System: Secure and easy-to-use chin strap mechanism.

Figure 3.1: The VINZ Vigo helmet features a robust design with a clear visor.

Figure 3.2: Side profile showcasing the visor mechanism and sleek design.

4. Sizing and Fit

A properly fitting helmet is critical for safety and comfort. To determine your correct helmet size, measure the circumference of your head just above your eyebrows and ears. Compare your measurement to the size chart below.

When trying on the helmet, it should feel snug around your head and cheeks without causing uncomfortable pressure points. The helmet should not move freely when you shake your head. If it does, try a smaller size.

5. Setup

5.1 Unpacking and Initial Inspection

Carefully remove the helmet from its packaging. Inspect the helmet for any signs of damage that may have occurred during shipping. Check the shell, visor, and chin strap for cracks, scratches, or deformities. If any damage is found, do not use the helmet and contact your retailer.

Figure 5.1: The helmet comes with a protective cover for storage.

5.2 Adjusting the Chin Strap

The VINZ Vigo helmet features a ratchet closure system for the chin strap. To adjust:

1. Place the helmet on your head.
2. Thread the chin strap through the D-rings or engage the ratchet mechanism until it is snug under your chin.
3. Ensure there is enough tension so that the helmet cannot be easily pulled off your head, but not so tight that it causes discomfort or restricts breathing. You should be able to fit one finger between the strap and your chin.
4. Secure any excess strap length using the provided strap holder.

6. Operating

6.1 Wearing and Removing the Helmet

To wear the helmet, hold it by the chin straps and pull it over your head, ensuring your ears are not folded. Once on, adjust the chin strap as described in Section 5.2. To remove, unfasten the chin strap and gently pull the helmet off your head from back to front.

6.2 Visor Operation

The clear visor can be easily opened and closed. Use the tab located on the visor to lift or lower it. Ensure the visor is fully closed when riding to protect your eyes from wind, debris, and insects. The visor is designed to be anti-scratch, but care should still be taken to avoid abrasive contact.

7. Maintenance

7.1 Cleaning the Exterior Shell

Clean the helmet's exterior with a soft cloth and mild soap and water. Rinse thoroughly and dry with a clean, soft cloth. Avoid abrasive cleaners or solvents, as they can damage the helmet's finish and structural integrity.

7.2 Cleaning the Visor

The visor should be cleaned with a soft, damp cloth and mild soap or a specialized helmet visor cleaner. Do not use paper towels or abrasive materials, as they can scratch the visor. Dry gently with a microfiber cloth.

7.3 Washing Removable Padding

The ear pads of the VINZ Vigo helmet are removable for cleaning. Gently detach them from the helmet. Hand wash them with mild soap and lukewarm water. Rinse thoroughly and allow them to air dry completely before reattaching them to the helmet. Do not machine wash or tumble dry.

7.4 Storage

Store your helmet in a cool, dry place away from direct sunlight and extreme temperatures. Use the provided helmet bag to protect it from dust and scratches when not in use. Do not store the helmet near chemicals or fuels.

Figure 7.1: The rear of the helmet, showing the Vinz branding and ventilation.

8. Troubleshooting

8.1 Visor Fogging

If your visor fogs up, especially in cold or humid conditions, try slightly opening the visor to allow for airflow. Consider using an anti-fog spray or insert designed for helmet visors.

8.2 Discomfort or Pressure Points

If you experience discomfort or pressure points, re-check your helmet size using the sizing guide in Section 4. Ensure the helmet is worn correctly and the chin strap is not overtightened. The padding will conform slightly over time, but persistent discomfort may indicate an incorrect size.

8.3 Chin Strap Issues

If the chin strap is difficult to fasten or unfasten, ensure the ratchet mechanism is clean and free of debris. Do not force the mechanism. If the strap is frayed or damaged, the helmet should be replaced.

9. Specifications

10. Warranty and Support

VINZ provides a 1-year availability for spare parts within the EU. For any questions, concerns, or support regarding your VINZ Vigo helmet, please refer to the manufacturer's official website or contact your point of purchase. Always ensure to provide your model number (BIS809M) when seeking support.