1. Product Overview
The Elecbee GX12 series aviation connector is a standard type, 2-pin male plug and female socket designed for panel mounting. It features a 3-hole square flange for secure installation and utilizes a solder-type wiring method, ensuring a reliable connection. These connectors are widely used in various applications requiring robust and dependable electrical connections.

Product Video Overview
Watch this video for a general overview of the GX12 series connectors, highlighting their features and common applications.
Video 1: An overview of the GX12 Male Female Connector series, showcasing its design and potential uses.
2. Specifications
| Feature | Detail |
|---|---|
| Product Type | GX12 Aviation Connector |
| Pin Configuration | 2 Pin (Female Plug, Male Socket) |
| Mounting Type | Panel Mount (3 Hole Square Flange) |
| Wiring Method | Solder Type |
| Mounting Size | 12mm |
| Item Model Number | EB-403-0169-H |
| Item Weight | 0.64 ounces |
| Package Dimensions | 9.84 x 7.87 x 3.94 inches |
3. Setup Instructions
This section provides detailed instructions for preparing and assembling the GX12 solder-type aviation connector.
3.1 Required Components and Tools
- Elecbee GX12 Male Plug and Female Socket
- Appropriate gauge electrical wires
- Soldering iron
- Solder (rosin core recommended)
- Wire strippers
- Heat shrink tubing (optional, for insulation)
- Heat gun or lighter (if using heat shrink tubing)
- Small Phillips head screwdriver (for cable clamp on male plug)
3.2 Preparation
- Safety First: Ensure all power is disconnected from the circuit you are working on. Wear appropriate safety gear, including eye protection.
- Prepare Wires: Carefully strip approximately 3-5mm of insulation from the end of each wire that will be connected to the pins. Ensure the stripped wire length is sufficient for soldering without excess bare wire.
- Pre-tin Wires (Optional but Recommended): Apply a small amount of solder to the stripped ends of the wires. This helps ensure a better connection.
- Prepare Connector Parts: If using heat shrink tubing, slide a piece onto each wire before soldering. Ensure it's long enough to cover the soldered joint and provide adequate insulation.

3.3 Assembly (Solder Type)
- Solder Wires to Pins: Carefully solder the prepared wires to the corresponding pins on both the male plug and female socket. Ensure a strong, clean solder joint. Pay attention to polarity if applicable to your application.
- Insulate Joints (Optional): If using heat shrink tubing, slide it over the soldered joints and apply heat with a heat gun or lighter until it shrinks tightly around the connection, providing insulation and strain relief.
- Assemble Male Plug Housing: For the male plug, thread the cable through the rear housing and secure it using the cable clamp screws. Then, screw the main body of the plug onto the pin assembly.
- Mount Female Socket: The female socket is designed for panel mounting. Insert the threaded portion into a 12mm hole on your panel and secure it with the provided nut from the other side. The 3-hole square flange provides additional stability and prevents rotation.
- Final Check: Visually inspect all connections for proper soldering and assembly. Perform continuity tests if necessary to ensure correct wiring.
4. Operating Instructions
Using the GX12 aviation connector is straightforward once properly installed.
- Connecting: Align the keyway (notch) on the male plug with the corresponding slot on the female socket. Push the male plug firmly into the female socket until it seats completely. Then, twist the threaded locking ring on the male plug clockwise until it is hand-tight to secure the connection.
- Disconnecting: Twist the threaded locking ring on the male plug counter-clockwise to loosen it. Once loose, pull the male plug straight out from the female socket. Avoid pulling by the cable itself.
Note: Always ensure the connection is fully seated and the locking ring is tightened to prevent accidental disconnection and ensure optimal electrical contact.
5. Maintenance
Regular maintenance helps ensure the longevity and reliable performance of your GX12 connectors.
- Cleaning: Periodically inspect the connector for dust, dirt, or debris. Use a clean, dry, lint-free cloth to gently wipe the exterior. For internal contacts, use a specialized electrical contact cleaner if necessary, ensuring the connector is completely dry before re-connecting.
- Inspection: Check for any signs of physical damage, such as bent pins, cracked housing, or loose connections. Also, inspect for corrosion on the metal parts.
- Storage: When not in use, store connectors in a clean, dry, and dust-free environment to prevent contamination and corrosion.
6. Troubleshooting
This section addresses common issues you might encounter with your GX12 connector.
| Problem | Possible Cause | Solution |
|---|---|---|
| No electrical connection | Poor solder joint, incorrect wiring, bent/damaged pins, not fully connected. | Inspect solder joints and wiring. Straighten bent pins carefully or replace if damaged. Ensure male plug is fully inserted and locking ring is tightened. |
| Loose connection / Intermittent signal | Locking ring not tightened, internal wiring loose, worn contacts. | Ensure locking ring is securely tightened. Re-check internal solder connections. If contacts are worn, replace the connector. |
| Difficulty connecting/disconnecting | Misalignment, debris in connector, damaged threads. | Ensure proper alignment of keyway. Clean any debris from inside the connector. If threads are damaged, the connector may need replacement. |
| Corrosion on metal parts | Exposure to moisture or harsh environments. | Clean with a suitable non-abrasive cleaner. Store in a dry environment. Consider protective covers if used in harsh conditions. |
7. Warranty and Support
Specific warranty information for the Elecbee GX12 2Pin Metal Aviation Panel Mount Male Female Socket Plug Wire Cable Connector is not provided in this manual. For warranty details, technical support, or further assistance, please contact the manufacturer, Elecbee, or your point of purchase.
Manufacturer: Elecbee
Model Number: EB-403-0169-H