1. Setup Instructions
1.1 Unpacking
Carefully remove all components from the packaging. Verify that all parts are present before proceeding with assembly.
1.2 Unit Placement
Place the main unit on a stable, flat surface. For optimal water flow, ensure the unit is positioned at the same level or higher than the mattress pad. Avoid placing the unit on the floor if the mattress pad is elevated.
Image: Proper placement of the Adamson B10 unit relative to the bed for efficient water circulation.
1.3 Connecting the Mattress Pad
Unroll the mattress pad and place it on your bed. Connect the hoses from the main unit to the designated ports on the mattress pad. Ensure connections are secure to prevent leaks.
Image: The Adamson B10 mattress pad positioned on a bed, demonstrating its coverage for a single sleeping area.
1.4 Filling the Water Tank
Open the water inlet on the main unit. Fill the tank with approximately 1/2 gallon (2 liters) of distilled water. Do not overfill. Ensure the cap is securely closed after filling.
Image: Diagram showing the principle of the water cooling system, where chilled water circulates through the mattress pad.
1.5 Initial Operation
After connecting and filling, power on the unit. Allow a few minutes for the water to circulate and the system to stabilize. The mattress pad will begin to cool.
Video: An overview of the Adamson B10 Bed Cooling System, demonstrating its components and basic functionality.
2. Operating Instructions
2.1 Control Panel Overview
The unit features a control panel with buttons for power, fan speed, fan cycle, timer, and negative ion function. Refer to the icons on the panel for specific functions.
2.2 Adjusting Fan Speed
Press the 'Fan Speed' button to cycle through available fan speed settings (F1-F4). F1 is the lowest speed, and F4 is the highest. Higher speeds result in more rapid cooling and increased fan noise.
2.3 Fan Cycle Modes
The 'Fan Cycle' button allows selection of various operational modes, such as continuous operation or timed intervals (e.g., run for 3 minutes, off for 3 minutes). Choose the mode that best suits your comfort and energy preferences.
2.4 Timer Function
Use the 'Timer' button to set a specific duration for the unit to operate before automatically shutting off.
2.5 Negative Ion Function
Activate the 'Negative Ion' function for air purification. This feature can be used independently or in conjunction with cooling.
3. Maintenance
Regular maintenance ensures the longevity and optimal performance of your Adamson B10 Bed Cooling System.
3.1 Draining the Unit
To drain the unit, remove the nozzle at the base. Allow all water to exit the system. This should be done periodically, especially before long periods of non-use.
3.2 Cleaning the Mattress Pad
Once a month, or as needed, hang the mattress pad to allow any residual water to fully drain and dry. This helps prevent odor and mold buildup. The mattress pad is made of 100% cotton and can be machine washed according to care instructions.
Image: The mattress pad hung for drying, illustrating proper maintenance to prevent odors and mold.
Video: Detailed instructions on how to perform maintenance on the Adamson B10 Bed Cooling System, including draining and cleaning.
3.3 Water Quality
Using distilled water is recommended to minimize mineral buildup and maintain system efficiency. If using tap water, consider adding a few drops of laundry sanitizer additive weekly to prevent odor and buildup.
4. Troubleshooting
4.1 Leaks
If leaks occur, first check all hose connections to ensure they are securely fastened. Verify that the water tank cap is tightly closed. Ensure the unit is placed on a level surface and not overfilled. Initial leaks may occur during the first use as the system primes; place a towel underneath to catch any drips.
Image: The Adamson B10 unit, highlighting the importance of secure installation to prevent leaks.
4.2 Insufficient Cooling
Ensure the water tank is adequately filled. Check that the fan speed is set to a desired level. Verify that the mattress pad is properly connected and water is circulating. The system cools the mattress pad by 7 to 12 °F, not to Arctic levels, and is not a substitute for room air conditioning.
4.3 Noise Levels
The unit's fan speed directly impacts noise levels. Lower fan speeds (F1-F2) produce less noise. Ensure the unit is on a stable surface to minimize vibrations.
5. Specifications
- Brand: Adamson
- Model Name: Adamson B10
- Model Number: B10G
- Size: Twin (75” L x 39” W)
- Fabric Type: 100% Cotton
- Special Features: Water Cooling System, 4 Fan Modes, Fan Speed Adjustable, Remote Control
- Power Consumption: 8 Wh (compared to 800 Wh for standard AC)
- Item Weight: 1.26 Kilograms
- Item Display Dimensions: 11.42 x 8.07 x 6.5 inches
- Product Care Instructions: Machine Wash (mattress pad)
- Water Resistance Level: Not Water Resistant (mattress pad)
6. Warranty & Support
6.1 Product Warranty
The Adamson B10 Bed Cooling System comes with a 5-year protection plan. This warranty covers manufacturing defects and ensures long-term optimal performance.
6.2 Customer Support
Should any issues arise or if you require assistance with your product, please contact our 24/7 customer service. Refer to the product packaging or our official website for contact details.
