Introduction
Thank you for choosing the Ibergrif M16303 Wall-Mounted Kitchen Faucet. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new faucet. Please read these instructions carefully before installation and retain them for future reference.
Product Overview
The Ibergrif M16303 is a wall-mounted kitchen faucet constructed from high-quality 304 stainless steel with a brushed finish, designed for durability and resistance to corrosion and scratches. It features a single lever for easy control of water flow and temperature, and a ceramic disc cartridge for reliable, drip-free performance.

Figure 1: Ibergrif M16303 Wall-Mounted Kitchen Faucet.
Setup and Installation
This faucet is designed for wall-mounted installation. Ensure you have all necessary tools and materials before beginning. Professional installation is recommended if you are unfamiliar with plumbing work.
Included Components
Verify that all components are present in the packaging:
- Faucet body with spout and handle
- Mounting hardware (e.g., eccentric S-unions, escutcheons, gaskets)
- Instruction manual

Figure 2: All installation materials are included for convenience.
Installation Steps (General)
- Prepare the Wall: Ensure the water supply lines are shut off. Mark the desired mounting points for the faucet on the wall, ensuring they are level and at the correct distance for your plumbing connections.
- Install S-Unions: Apply plumber's tape to the threaded ends of the eccentric S-unions. Screw the S-unions into the wall water supply outlets. Adjust them until the distance between their centers matches the faucet's inlet spacing (typically 150mm) and they are level.
- Attach Escutcheons: Place the decorative escutcheons over the S-unions, flush against the wall.
- Mount the Faucet Body: Place gaskets onto the faucet's inlet nuts. Connect the faucet body to the S-unions, tightening the nuts securely with a wrench. Avoid overtightening.
- Test for Leaks: Slowly turn on the main water supply and check all connections for leaks.

Figure 3: Product dimensions for installation planning. The faucet has a spout reach of 300mm and a height of 268mm from the wall connection.
Operating Instructions
The Ibergrif M16303 faucet is designed for simple and intuitive operation.
Water Flow and Temperature Control
- Turn On/Off: Lift the single lever handle to turn on the water flow. Push it down to turn off.
- Adjust Temperature: Move the lever to the left for hot water and to the right for cold water. The ceramic cartridge ensures smooth and precise temperature adjustment.
- Adjust Flow: The height to which the lever is lifted controls the water flow rate.

Figure 4: The single lever controls both hot and cold water, indicated by red and blue arrows.
Spout Rotation
The faucet spout can rotate 360 degrees, providing flexibility and convenience for various sink tasks.

Figure 5: The faucet spout offers 360-degree rotation for enhanced usability.
Water-Saving Aerator
The integrated high-quality aerator provides a smooth, splash-free water flow and helps conserve water by up to 30%.

Figure 6: The faucet features a NEOPERL water-saving aerator for efficient water usage.
Maintenance
Regular maintenance will ensure the longevity and optimal performance of your Ibergrif M16303 faucet.
Cleaning the Faucet
- Clean the brushed stainless steel finish regularly with a soft cloth and mild soap or a non-abrasive cleaner.
- Avoid using abrasive cleaners, scouring pads, or harsh chemicals, as these can damage the finish.
- Rinse thoroughly with clean water and dry with a soft cloth to prevent water spots.
Aerator Maintenance
If water flow decreases or becomes irregular, the aerator may be clogged with debris.
- Unscrew the aerator from the tip of the spout.
- Rinse the aerator screen under running water to remove any particles. For stubborn deposits, soak in a vinegar solution.
- Reassemble the aerator and screw it back onto the spout.

Figure 7: Close-up view of the aerator and connection points, highlighting areas for maintenance.
Ceramic Cartridge
The faucet is equipped with a durable ceramic disc cartridge, designed to prevent leaks and drips for a long operational life. If a leak occurs from the handle area, the cartridge may need inspection or replacement. Contact customer support for assistance.
Troubleshooting
This section addresses common issues you might encounter with your faucet.
- Low Water Flow: Check if the aerator is clogged (refer to Maintenance section). Ensure water supply valves are fully open.
- Leaks from Spout: This is typically caused by a worn aerator gasket or a faulty cartridge. Clean or replace the aerator gasket first. If the issue persists, the ceramic cartridge may need replacement.
- Leaks from Handle Base: This usually indicates a problem with the ceramic cartridge. Contact customer support for guidance on replacement.
- Water Temperature Issues: Ensure both hot and cold water supply lines are connected correctly and fully open.
For issues not listed here or if troubleshooting steps do not resolve the problem, please contact Ibergrif customer support.
Specifications
| Feature | Specification |
|---|---|
| Model Number | M16303 |
| Brand | Ibergrif |
| Material | 304 Stainless Steel (Faucet Body), Brass (Handle Material) |
| Finish | Brushed |
| Installation Method | Wall-Mounted (Monotrou) |
| Product Dimensions (L x W x H) | 30 x 20 x 26.8 cm (11.8 x 7.9 x 10.5 inches) |
| Item Weight | 1.17 kilograms (2.58 lbs) |
| Number of Handles | 1 (Lever Style) |
| Handle Placement | Right |
| Special Feature | Rotary (360° Swivel Spout) |
| Included Components | Installation hardware |
| Cartridge Type | Ceramic Disc |
Warranty and Support
For warranty information, technical support, or to order replacement parts, please contact Ibergrif customer service. Keep your purchase receipt as proof of purchase.
Manufacturer: Ibergrif Griferias S.L
Contact Information: Refer to the Ibergrif official website or your purchase documentation for the most current support contact details.
Important Safety Information
- Always shut off the main water supply before attempting any installation, maintenance, or repair.
- Wear appropriate personal protective equipment (e.g., safety glasses, gloves) during installation.
- If you are unsure about any part of the installation or repair process, consult a qualified plumber.
- Do not use excessive force when tightening connections to avoid damaging the faucet or plumbing.